light AUDI A5 COUPE 2018 Owners Manual

Check ing and F illing
edge of the reservoir and result in damage
to the vehicle .
- Do not get any bra ke fluid on the ve hicle
paint, beca use it will cor rode t he pa int .
Battery
General warnings about batteries
Because of the complex power s upply, a ll wor k
on batte ries such as disconnecting, rep laci ng,
etc. s hou ld
onl y be per formed by an auth or ized
Aud i dea ler o r autho rized Aud i Serv ice Facility
c;> .&. .
The te rm "vehicle battery " refers to the 12 Vo lt
b at tery i n your veh icle.
Detailed warnings for the vehicle battery:
®
Wear eye protection .
A
Battery acid is highly corrosive. Wear p ro-
tective gloves and eye p rotection.
@
F ire, sp arks , open flame and smo king a re
forbidden.
A
A highly explosive mixtu re of gases can
form when charging ba tte ries.
®
Keep c hildren away from battery acid and
batteries.
A WARNING
All work on the batte ry o r electrical system in
your vehicle can result in injuries, chemical
burns, accide nts o r burns. Because of this, a ll
wor k mu st be perf ormed
only by an au thor­
ize d Aud i de aler o r authorized Aud i Se rv ice
Facility .
A WARNING
California Proposit io n 65 Warning:
- B attery posts, termin als and re late d a cces­
so ries contai n lead and lead compounds,
chem ica ls known to the State of California
to cause cance r and rep roduct ive p roblems.
Wash hands after handling.
338
(D Note
P rotect the vehicle battery aga inst freezing if
the ve hicle wi ll be par ked for long periods of
time so t hat it is not destroyed by "freezing"
c;> page339.
@ For the sake of the environment
'8 Batteries conta in polluting s ubstances such
as sulfur ic acid and lead. Contact an aut ho r­
i zed Audi dealer or authorized A udi Service
Fac ility for more informat io n.
· Vehicle battery
The term "vehicle battery" refers to the 12 Volt
battery in your vehicle.
Not running the v ehicl e for long period s of
time
If you do not d rive your vehicle for severa l days o r
weeks, electrical equ ipment is gradually sca led
back or sw itched off . Th is reduces energy use and
ensures the vehicle will be ab le to s tart after long
per iods o f time
9 page 155. Some co nvenience
funct io ns, such as interio r lighting o r power seat
adjus tment, may not be av ail abl e un de r c ertain
c irc umstances. These convenience functions will
be available again once you switch the ignition on
and sta rt the engine .
E ven when ele ctrical eq uipment is swi tched off,
t h e eq uipment can still dra in the vehicle ba tte ry
i f the ve hicle is not driven for long periods of
time. Deep drai ning results in a chemica l reaction
that destroys the ins ide of the vehicle batte ry.
The vehicle battery must be cha rged every month
to reduce the risk of this happening
c;> page 339.
Contact an authorized Aud i dea ler or authorized
Audi Se rvice Fac il ity for more information.
Winter operation
Co ld weather places higher demands on the vehi­
cle battery. T his resu lts in reduced starting abili­
ty. Have the vehicle battery chec ked by an au­
thorized Aud i dea ler or authorized Audi Service
Fac ility befo re t he cold ti me of year.

Charging the vehicle battery
Fig. 280 Engine compartment : connectors for a charger
and jump start cables
Requirement: only use chargers with a maximum
charging voltage of 30 amps/14.8 Volts.
The
vehicle battery cables remain connected .
.,. Read the warnings¢ & in General warnings
about batteries on page 338
and ¢ ,& .
.,. Switch off the ignition and all electrical equip­
ment .
.,. Open the hood ¢ page 331 .
.,. Open the red cover on the positive terminal
¢ fig. 280 .
.,. Clamp the charger terminal clamps to the jump
start pins
according to the instructions . (pin
under the red cover= "positive", pin with hex­
agonal head= "negative").
.,. Insert the power cable for the charging device
into the socket and switch the device on.
.,. At the end of the charging process, switch the
charger off and pull the power cable out of the
socket .
.,. Remove the charger terminal clamps.
.,. Close the red cover on the positive terminal.
.,. Close the hood ¢ page 331 .
A WARNING
-A highly explosive mixture of gases can form
when charging batteries. Only charge the
vehicle battery in well-vent ilated areas.
-A drained vehicle battery can freeze at tem­
peratures around 32
QF (0 QC). A frozen or
thawed vehicle battery must not be charged
and must not be used anymore. The battery
housing can crack and battery acid can leak
out if ice forms, which increases the risk of
an explosion and chemical burns. Contact an
Checking and Filling
authorized Audi dealer or authorized Audi
Service Facility for more information.
- Do not connect or disconnect the charging
cable while charging because this increases
the risk of an explosion.
@ Tips
- Only charge the vehicle battery through the
connections in the engine compartment.
- Read all of the manufacturer's instructions
for the charger before charging the vehicle
battery.
Windshield washer system
Fig. 281 E ngine compartmen t: was her fluid reservoi r cap
The windshield washer fluid reservoir O contains
the cleaning solution for the windshield and the
headlight washer
system*¢ page 332, fig. 276 .
The reservoir capacity can be found in
¢ page 388.
To reduce the risk of lime scale deposits on the
spray nozzles, use clean water with low amounts
of calcium. Always add window cleaner to the wa­
ter . When the outside temperatures are cold, an
anti -freezing agent should be added to the water
so that it does not freeze.
(D Note
-The concentration of ant i-freezing agent
must be adjusted to the vehicle operating
conditions in the respective climate . A con­
centration that is too high can lead to vehi-
cle damage.
- Never add radiator anti-freeze or other addi-
tives to the washer fluid.
.,..
339

Wheels
Wheels and Tires
General information
.,.Check your tires regularly for
damage (punctures, cuts, cracks
and bulges). Remove foreign ob­
jects from the tire tread.
.,. If driving over curbs or similar
obstacles, drive slowly and ap­
proach the curb at an angle.
.,.Have faulty tires or rims re­
placed immediately.
"'Protect your tires from oil,
grease and fuel.
.,.Mark tires before removing
them so that the same running
direction can be maintained if
they are reinstalled.
"'Lay tires flat when storing and
store them in a cool, dry location
with as little exposure to light as
possible.
(D Note
-Please note that summer and
winter tires are designed for
the conditions that are typical in those seasons. Audi recom­
mends using winter tires dur­
ing the winter months. Low
temperatures significantly de­ crease the elasticity of summ­
er tires, which affects traction
Wheels
and braking ability. If summer
tires are used in very cold
temperatures, cracks can form
on the tread bars, resulting in
permanent tire damage that
can cause loud driving noise
and unbalanced tires.
-Burnished, polished or
chromed rims must not be
used in winter driving condi­
tions. The surface of the rims
does not have sufficient corro­
sion protection for this and
could be permanently dam­ aged by road salt or similar
substances.
Tire designations
Fig. 282 T ir e designations on the side -
wall Ill>
341

Wheels
check you r tires as soon as possible, and inflate
them to the proper pressure. Driving on a signifi­
cantly under-inflated tire causes the tire to over­
heat and can lead to t ire failure. Under-inflation
also reduces fuel efficiency and t ire tread life,
a nd may affect the veh icle's handling and stop ­
p ing ability .
Please note that the TPMS is not a substit ute for
proper tire maintenance, and it is the driver's re­
sponsib ility to ma inta in correct tire pressure,
even if under-inflation has not reached the level
to tr igger illum inat io n of the TPMS low tire p res­
sure tellta le.
Your veh icle has also bee n eq uipped w ith a TPMS
malfunct ion i nd icator to indicate when the sys­
t e m is not operat ing properly. The TPMS ma l­
f u nction indicator is comb ined w ith the low tire
p ress ure tellt ale. Whe n the system dete cts a
malfunct ion, the te lltale will flash for approxi­
mate ly one min ute and then remain continuo usly
i l luminated. This sequence will continue upon
subseq uent veh icle start- ups as long as the ma l­
function ex ists .
When the malf unctio n indicator is ill uminated,
the system may not be able to detect or signa l
low tire pressure as intended . TPMS ma lf u nctions
may occur for a variety of reasons, including the
installation of replacement or alternate t ires or
wheels on the vehicle that prevent the TPMS from functioning prope rly . Always c heck the
TPMS malfunct ion tellta le afte r replacing one o r
mo re t ires o r whee ls on your ve hicle to e nsu re
t hat the repla cement or altern ate t ires and
wheels a llow the TPM S to con tinue to function
p roperly.
If the tire pressure monitoring indicator
appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction .
Using the ABS sensors, the tire pressure mon itor­
ing system compares the tire tread circ umfer­
ence and vibration cha racteristics of the individu­
a l tires. If the pressure changes in one or more
tires, this is ind icated i n the instrument cluste r
360
display with an indicato r light RE and a message .
If only one tire is affected, the location of that
t ir e will be indicated.
The tire press ures mus t be sto red in the Infotain­
ment system again each time the p ress ures
c h ange (switching between partia l and full load
pressure) or afte r changing or replac ing a tire on
yo ur vehicle
c:> page 361. The tire p ressure mon i­
tor ing system on ly monitors the tire pressure you
have stored . Refer to the t ire pressure label for
t h e recommended t ire pressu re for you r vehicle
<=:> page 351, fig . 285.
Tire tread circumference and vibrat ion characte r­
i stics can change and ca use a tire press ure warn­
i ng if:
-the t ire pressure in one or more tires is too low
-the t ires have structural damage
-t he t ire was rep laced or the t ire pressu re was
changed and it was not stored
c:> page 361
-tires tha t are o nly p artially used are replaced
with new tires
Indicator lights
RE -Loss of pressure in at least one tire c:> &. .
Check the tir es and rep lace or repair if necessary.
Ch eck/correct the pres sures of all fou r tires and
store the press ure again in the Infotainmen t sys ­
tem
c:> page 361 .
mm (T ire Pressure Mon itor ing Sys tem) Tire
pressure: malfunction! See owner' s manual.
If
mm appea rs a fter switching the ignition on or
whi le dr iving and the
RE indicator light in the in­
strument cl uster bli nks for approximate ly one
minute and then stays on, the re is system ma l­
funct ion. T ry to store the correct t ire pressures
c:> page 361. In some cases, you m ust dr ive for
severa l m in utes after sto ring the pressures unt il
the ind icator lig ht turns off . If the indica to r li gh t
does tur n off or turns on again af ter a s hort peri­
o d of t ime, dr ive to an author ized Audi dealer or
a uth o riz e d Aud i Serv ice Facili ty immedia tely to
have the mal function cor rected.
IJ,,

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from an authorized Audi dealer or au­
thorized Service Facility. Read and follow the in­
structions for use on the packaging .
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health .
- Always store cleaning and care products out
of reach of children to reduce the risk of poi­
soning .
@ For the sake of the environment
- Preferably purchase environmentally-friend­
ly cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve­ hicle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect .
Before washing, rinse off heavy deposits with
plenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
Also, wash the underside of your vehicle once road salt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash ­
er, always follow the operating instructions pro­
vided with the pressure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at seals on
362
side windows, doors, the hood, the luggage com­
partment lid or the panorama glass roof* or at
tires, rubber hoses, insulating material, the pow­
er top*, sensors* or camera lenses". Keep a dis­
tance of at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozzles or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °() .
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows, the panorama glass
roof* and the power top* are closed and the
windshield wipers are off. Follow instructions
from the car wash operator, especially if there
are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the vehicle starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply the product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
clean using a neutra l shampoo and a soft micro­
fiber cloth.
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a chamois.
.,._

<( a, .... N ,....
N .... 0 \0
3 a,
A WARNING ,~
- Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­ dents .
- To reduce the risk of cuts, protect yourself from sha rp metal components when wash­
ing the underbody or the inside of the wheel
housings .
- After washing the vehicle, the bra king effect
may be de layed due to mo isture on the
bra ke rotors or i ce in the w inte r. This in­
cre ases the risk of an ac ciden t. T he bra kes
must be dried first with a few careful brake
applications .
(D Note
-If yo u wash t he ve hicl e in an au tom atic c ar
wash, yo u m ust fold the exterior m irrors in
to reduce the risk of damage to the mirrors .
Power folding exterior mirrors * must on ly
be fo lded in and out using the power folding
funct ion.
- To reduce the risk of damage to the rims
and tires, compare the width between the
whee ls on your vehicle w it h the distance be­
tween the g uide rails in the car wash .
- To reduce the risk of damage, compare the
height and width of your vehicle with the
-
Ca re and cleaning
height and w idth of the inside of the ca r
was h.
- T o red uce the risk of pa int damage, do not
was h the vehicle in d irect sun light .
- T o re duce the risk of d am age, do not w ash
t he power top * w ith a pressu re washe r.
- T o re duce the risk of d amage to the surf ace,
do not use insect removing sponges, k itche n
sponges or s imilar items .
- Ma tte finish painted veh icle components :
- To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax .
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint . The paint could be damaged
when the stickers or magne ts are re­
moved .
@ For the sake of the environment
Only wash t he vehicle in facilities spec ially de­
s igned for that p urpose. This will reduce the
risk of dirty wate r contamina ted with o il from
ente ring the sewe r sys tem.
Cleaning and care information
When cleaning and caring for individual vehicle
components, refer to the following tables. The information conta ined there is s imply recom ­
mendations . Fo r quest ions or for components that are not
listed, cons ult an autho riz ed Aud i
dealer or authorized Audi Service Fac ility. Also
follow the information fo und
in <=> ,& .
Exter io r cleaning
Component Situation Solution
Wind shield wiper
Deposits <=> page 68, Cleaning the wiper blades
blades
Headlights /
Deposits Soft sponge with a mild soap so lution a)
Tail lights
Sen sors /
Deposits Sensors: soft cloth wit h a solven t-free cleaning sol ution
camera lenses Camera lenses: soft clot h w ith an alcoho l-free cleaning
solution
Snow/ice Hand brush/solven t-free de-icing spray
363
...

<( a, .... N ,....
N .... 0 \0
3 a,
Care and cleaning
Component Situation Solution
Pla sti c pa rts
Deposits Damp doth
H eavier depos its Mild soap solution
a), detergent-free p lastic clean ing so lu -
tion, if ne cessary
D ispl ays/in stru-Deposits Soft cloth with LCD cleaner; dust in the lower area of the
ment cl uster instrument cluster can be removed using a soft brush.
Controls Deposits Soft brush, then a soft cloth
with a mild soap solutional
Saf ety be lts Deposits Mild soap solution al, allow to dry before letting them re-
tract
Textile s, Deposits adhering to Vacuum cleaner
a rtifi cial le ather , the su rface
Alcanta ra Water-based deposits Absorbent cloth and mild soap solutional
such as coffee, tea,
b lood, etc.
Oil-based deposits Apply a m ild soap solution
al, blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Specia
l stain remover, blot with absorbent material, treat
as ink, nail polish,
la-afterward with mild soap solution, if necessary a)
tex paint, shoe pol-
ish, etc.
Natural leather F resh stains Cotton cloth with a mi ld soap so lutiona l
Water-based deposits Fresh stains : absorbent cloth
such as coffee, tea, Dried stains: stain remover suitable for leather
blood, etc.
Oil-based deposits Fresh stains: absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc. Dried stains: oil cleaning spray
Special deposits such Spot remove r su itab le for leathe r
as ink, nail polish,
la-
tex paint, shoe po l-
ish, etc .
Care Regularly apply condit ion ing cream that protects from
lig ht and penetrates into the ma teria l. Use specia lly- co l-
ored cond ition ing cream, if necessary.
Carb on part s Deposits clean the same way as plast ic parts
a) M ild soap solution: maximum two tab lespoons of ne utral soap in 1 quar t (1 lite r) of water
.&, WARNING
The windshie ld may not be treated with wa­
ter-repelling windshield coating agents. Un­
favorable cond itions such as wetness, dark­
ness, or low sun can result in increased glare .
Wiper blade chatter is also possib le .
-
(D Note
-H ea dlight s/ta il lights
-Neve r clean headlights or tail lights w ith a
dry cloth o r sponge.
-Do not use any cleaning product that con­
tains alcoho l, because they could ca use
cracks to form.
..,.
365

Care and cleaning
-Wheels
-Never use any paint polish or other abra-
sive materials.
- Damage to the protective layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Sensors/camera lenses
- Never use warm or hot water to remove
snow or ice from the camera lens. This
could cause the lens to crack.
- Never use abrasive cleaning materials or
alcohol to clean the camera lens. This
could cause scratches and cracks.
- Power top
- Remove bird droppings immediately.
- Never use gasoline, spot remover, ben-
zene, paint thinner or other solvents to re­
move.
- Door windows
- Remove snow and ice on windows and ex-
terior mirrors with a plastic scraper. To avoid scratches, move the scraper only in
one direction and not back and forth.
- Never remove snow or ice from door win­
dows and mirrors using warm or hot water
because this could cause cracks to form.
- To avoid damage to the rear window de­
fogger, do not apply any stickers on the heating wires on the inside of the window.
- Decorative parts/trim
- Never use chrome care or cleaning prod-
ucts.
- Paint
-To reduce the risk of scratches, the vehicle
must be free of dirt and dust before pol­
ishing or waxing.
- To prevent paint damage, do not polish or
wax the vehicle in direct sunlight .
- To reduce the risk of paint damage, do not
polish away rust spots .
- Remove cosmetics and sunscreen immedi­
ately- these could damage the paint.
- Displays/instrument cluster
- Make sure that the instrument cluster is
366
switched off and has cooled off before
cleaning it. - Displays, the
instrument cluster and the
trim surrounding it must not be cleaned
with dry cleaning methods because they
could become scratched.
- Make sure no fluids enter the spaces be­
tween the instrument cluster and the
trim, because that could cause damage.
- Controls
- Make sure that no fluids enter the con-
trols, because this could cause damage.
- Safety belts
- Do not remove the safety belts to clean
them.
- Never clean safety belts or their compo­
nents chemically or with corrosive fluids
or solvents and never allow sharp objects
to come into contact with the safety belts.
This could cause damage to the belt web­
bing.
- If there is damage to the webbing, the
connections, the retractors or the buckles, have them replaced by an authorized Audi
dealer or authorized Audi Service Facility .
-Textiles/artificial leather/ Alcantara
- Never treat artificial leather/ Alcantara
with leather care products, solvents, floor
polish, shoe polish, spot remove or similar
products.
- Have a specialist remove stubborn stains
to prevent damage.
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the
seat.
- Objects with sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
- Open hook and loop fasteners, for exam­
ple on clothing, can damage seat covers.
Make sure hook and loop fasteners are
closed.
- Natural leather
- Never treat leather with solvents, floor
polish, shoe polish, spot remover or simi­
lar products.

<( a, .... N ,....
N .... 0 \0
3 a,
-Objects with sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
-Never use steam cleaners, brushes, hard
sponges, etc . when cleaning.
-Do not tu rn on the seat heat ing * to d ry the
seat.
-To help preven t the leather from fading,
do not leave the vehicle in direct sunlight
for long periods of t ime. If leaving the ve­
hicle parked for long periods of t ime, you
should cover the leather to protect it from
direct sunlight .
(D Tips
-Insects are easier to remove from paint that
has been fresh ly waxed.
-Regular waxing can prevent rust spots from
fo rm ing .
Placing your vehicle out
of service
If you would like to take your vehicle o ut of serv ­
ice for a longer time, co ntact an a uth orized Audi
dea le r or autho rized Aud i Serv ice Facility. They
will adv ise you of importan t measures, such as
corros io n protection, se rvice and storage proce­
du res. A lso fo llow the information about the ve ­
hicle battery
r=> pog e 338.
Care and cleaning
367

Emergency assistance
Loosening the wheel bolts
Fig. 291 Wheel: loosening the wheel bolt
• Slide the wheel wrench (from the vehicle tool
kit) all the way onto the wheel bolt.
• Turn the wheel bolt approximately one turn to
the left -arrow-. To reach the required torque,
hold the end of the wheel wrench. If the wheel
bolt will not loosen, press carefully on the
whee l wrench with your foot. Hold onto the ve­
hicle securely while during this and make sure
your stance is stable .
A WARNING
To reduce the risk of an accident, only loosen
the wheel bolts gently (one turn) before rais­
ing the vehicle with the veh icle jack*.
Raising the vehicle
Fig . 292 Sill panels: markings
372
Fig. 293 Sill: positio ning the vehicle jack
• Place the veh icle jack* (vehicle tool kit) on a
firm s urface. Use a flat, stable support if neces­
sary. On a slippery surface such as tile, you
should use a non-slip pad (such as a rubber
mat)¢ &.
• Find the marking on the sill that is closest to
the tire that will be changed
¢fig. 292. Behind
the marking, there is a lifting point on the side
sill for the vehicle jack*.
• Turn the handwheel to raise the vehicle jack*
under the lifting point on the side sill until the
bracket on the jack @ completely covers the
notch on your vehicle.
• Align the vehicle jack* so the bracket @covers
the notch and the base ® is flat on the ground.
The base ® must be directly under the lifting
point @.
• Mount the crank on the vehicle jac k*: insert the
crank into the opening on the handwheel. Turn
the crank to the left or right to secure it.
• Continue ra is in g the veh icle jack* with the
crank until the wheel lifts off the ground slight­
ly.
A WARNING
- Ma ke sure the vehicle jack* is stable. Th ere
is a risk of injury when the ground is slick or
soft, because the vehicle jack* could slide or
sink.
- Only raise your vehicle with the vehicle jack*
provided by the factory . If you use a vehicle
jack designed for another vehicle, your vehi­
cle can slide and cause injury.
- Position the vehicle jack* only at the desig­
nated mounting points on the side sill and
align the jack. Otherwise, the vehicle jack*