light AUDI A6 1995 C5 / 2.G 01E Transmission Bearing House And Torsen Differential Workshop Manual

34-57


When pulling off, bearing housing is pressed slightly off end cover by
spring -A-.
- Note position of spring plate -C- when removing bearing housing.

Outer diameter (concave side) towards shims
- Remove shims -B-, note thickness re-determine if necessary Page
34
-85
.

- Pull Torsen differential out of end cover.
Pa
ge 5 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, removi...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5

34-84


- Guide oil collector from interior of end cover with support arm leading
through hole of end cover (arrow), until O-ring can be fitted from
outside onto oil collector.
- Lightly oil new O-ring and fit.
- Insert oil tube of oil collector into input shaft.

- Turn oil collector until the positioning segment is located in the
machined recess of the end cover (arrow).
- Press in oil collector onto stop.
- Slide assembly sleeve, Part No. 01E 311 120, onto selector shaft.
- Check neutral position of followers.
Selector gates must align.
Pa
ge 33 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, rem...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5

34-85

- Install complete selector shaft.

- Screw locking bolts -A- for selector shaft into transmission housing.
- Aluminium and steel bolts must not be interchanged when installing.
Tightening torques: for aluminium locking bolts = 50 Nm, and for steel
locking bolts = 70 Nm.
- Lightly oil new O-ring for cover for selector shaft and fit.
- Fit cover for selector shaft.
- Apply sealing paste AMV 188 000 02 to bolts -B- (Qty. 3) before
installing and tighten.
- Slide Torsen differential onto splines of hollow shaft.

Parts catalog - Press Torsen differential in direction of arrow, and measure distance
between top edge of bolted end cover and front edge of outer race of
ball bearing for Torsen differential.
- Determine required shim(s) from following table.
Pa
ge 34 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, rem...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5

34-87


- Insert spring plate -C- into bearing housing.
Installation position: larger diameter (concave side) towards the shims.
- Fit shims -B- as determined in table.
- Fit spring -A- to end of drive flange.
- Lightly oil new O-ring for bearing housing and fit.
- Oil small needle bearing in drive pinion.
- Insert complete bearing housing and pull home evenly.
- Tighten bearing housing using diagonal sequence.
- Fill new seal for drive axle between sealing lip and dust lip with sealing
grease G52 128 A1.
- Pull a thin protective hose tightly onto splines of input shaft.

- Drive on seal for input shaft.

Pressing-in depth (factory): 3.5 mm
Pressing in depth (repairs): 4.5 mm
Pa
ge 37 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, rem...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5