AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual A6 1995 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/1288/w960_1288-0.png AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual

Page 1 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-27
 
  
Clutch release mechanism, 
servicing 
1 - 
Transmission 
2 - 
Intermediate piece 
Replace if damaged
3 - 
Shaft seal For input shaftRemoving  Fig. 1Installing  Fig. 2Pressing-in depth (fact

Page 2 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-28
 
  
6 - 
Clutch release lever 
Removing  Fig. 3Must engage in the lugs in intermediate 
piece when installed   Fig. 4
 
Before installing, coat contact surface of 
clutch slave cylinder push ro

Page 3 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-29
 
  
10 - 
Clutch slave cylinder 
Bleeding clutch system   Page 30
-25
Removing and installing   Page 30
-32
When installing, push on until the securing 
bolt can be fitted 
11 - 
Bolt, 20 Nm Se

Page 4 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-30
 
    
Note:  
Do not damage contact surface of shaft seal on input shaft.   Fig. 1  Removing shaft seal for input shaft 
-  pry seal out carefully with a screwdriver. 
    
Fig. 2  Installing s

Page 5 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-31
 
    
Fig. 3  Removing clutch release lever
-  Loosen bolt -1-, remove leaf spring -2- and press back detent (arrow).
-  Remove clutch release lever -4- together with release bearing -3-. 
-  D

Page 6 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-32
      
Clutch slave cylinder, removing and 
installing
 
     
Removing  
    
-  Unbolt left drive axle -A- from transmission and move clear to one side.
-  Remove heat shield -B- from transmis

Page 7 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-33
 
    
Installing  
Installation is carried out in the reverse order, when doing this note the 
following:  
Note:  -  To disconnect line, first pry out retaining clip -A- with a screwdriver unt

Page 8 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-34
 
    
-  Coat area -a- of collar with Lithium grease G 052 150 A2 before 
mounting the slave cylinder into the transmission housing. 
-  Lightly coat contact surface for plunger to clutch relea

Page 9 of 9

AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Release Mechanism Workshop Manual 30-35
 
    
Tightening torques   -  To connect line to slave cylinder, press in retaining clip -A- as far as it 
will go. 
-  Push line into slave cylinder until it engages audibly. 
-  Install trans