engine AUDI A6 1995 C5 / 2.G 01E Transmission Clutch Service Workshop Manual

30-37


Notes:
Parts catalog
Centering mandrel 3176 Grease G 000 100Observe general repair notes Page 00
-11
.
For vehicles with V6 2.7 L-Biturbo engine, a SAC-clutch plate (self
adjusting clutch plate) is installed, on which an adjustment ring must
be reset except during replacement Page 30
-42
.
Replace clutch plates and pressure plates with damaged or loose
rivets. Select the correct clutch plate and pressure plate according to engine
code: Clean input shaft splines and (in the case of used clutch plates) the
hub splines. Remove corrosion and apply only a very thin coating of
grease G 000 100 to the splines. Then move clutch plate to and fro on
input shaft until hub moves freely on shaft. Excess grease must be
removed. Pressure plates have an anti-corrosion coating and are greased. Only
the contact surface may be cleaned, otherwise the service life of the
clutch will be considerably reduced. If the clutch has burned out, thoroughly clean the bellhousing, flywheel
and parts of the engine facing the transmission to reduce the smell of
burned linings.
Pa
ge 2 of 10 Clutch, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.3

30-38


Clutch (SAC pressure plate) for vehicles
with 6-cylinder 2.7 liter bi-turbo engine

Before working on the clutch, the transmission must
be removed Page 34
-18
.
Repair Manual, 2.7 Liter V6 5V BiTurbo Engine
Mechanical, Engine Code(s): APB, Repair Group 13
1 -
Dual-mass flywheel
Ensure centering pins are tightly seatedContact surface for clutch lining must be
free of grooves, oil and grease Removing and installing
Pa
ge 3 of 10 Clutch, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.3

30-39


Repair Manual, 2.7 Liter V6 5V BiTurbo Engine
Mechanical, Engine Code(s): APB, Repair Group 13
2 -
Bolt
Vehicles with dual-mass flywheel: tighten
bolt to 60 Nm, then turn a further 180 Always replace
3 -
Clutch plate
Install with spring pack (coil springs) or the
word "Getriebeseite" towards pressure
plate and transmission Centering Page 30
-45
Do not greaseClutch plate diameter from Page 00
-3
Pa
ge 4 of 10 Clutch, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.3

30-40


Repair Manual, 2.7 Liter V6 5V BiTurbo Engine
Mechanical, Engine Code(s): APB, Repair Group 13
4 -
SAC pressure plate
Removing and installing Page 30
-45
Resetting adjuster ring Page 30
-42
Checking ends of diaphragm spring Fig. 1 Checking spring connection and riveted
fastenings
5 -
Bolt, 22 Nm Tighten gradually in diagonal sequence
and in several stages
6 -
Needle roller bearing Removing and installing
Pa
ge 5 of 10 Clutch, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.3

30-41


Note:
In case of repair, always allocate clutch pressure plate and clutch disc to
engine code according to to parts catalog. Fig. 1 Checking ends of diaphragm springs
Wear up to half of the diaphragm spring thickness is permissible
- Check diaphragm springs and spring connection between pressure
plate and cover for cracks, rivet connections and for secure fit.
- Replace clutches with damaged springs or with loose rivet connections
(arrows).
Pa
ge 6 of 10 Clutch, servicin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.30.3