AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual https://www.carmanualsonline.info/img/6/1193/w960_1193-0.png AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual

Page 1 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-73
 
     
Driveshaft, servicing 
     
Important notes
 
     
A distinction is made between two 
driveshafts: 
     
Driveshaft made of steel
     Driveshaft made of carbon fiber
      Only carbo

Page 2 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-74
      
Specific notes for carbon fiber driveshafts:  
     
WARNING! 
     
Driveshaft made of carbon fiber 
     
do not impact / do not hi
t
     
do not drop 
     
If the surface is damaged,

Page 3 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-75
      
Notes for all driveshafts:  
     
General repair notes   page 00
-27
 .
     
Do not bend the driveshaft, maximum 
permissible bending angle is 25  . Otherwise 
the universal joint may b

Page 4 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual      
After disconnecting driveshaft from rear final 
drive, an additional balance washer (thick 
washer) that may be located between shim and 
bolt head may not be reinstalled. 
Pa
ge 4 of 23 Drivesh

Page 5 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-76
 
  
1 - 
Rear final drive 
2 - 
Gasket 
Always replaceRemove protective film and attach self-
locking side of gasket to drive flange. Degrease drive flange
3 - 
Constant velocity joint Maximum

Page 6 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-77
 
  
6 - 
Universal joint 
Maximum permissible bending angle 25 
7 - 
Adjustment shim 
Determine thickness   page 39
-90
8 - 
Hex-bolt - 23 Nm 
9 - 
Center driveshaft bearing 
10 - 
Driveshaft

Page 7 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-78
 
  
12 - 
Backing plate 
13 - 
Constant velocity joint 
Maximum permissible bending angle 8 
14 - 
Gasket 
Always replaceRemove protective film and attach self-
locking side of gasket to drive

Page 8 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-79
      
Driveshaft, removing and installing
 
     
Special tools and equipment  
    
Removing  
 Repair Manual, Engine Mechanical, Repair Group 26; removing and 
installing exhaust system   
 R

Page 9 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-80
      
-  Remove heat shields above driveshaft.
    
-  Unbolt heat shield for driveshaft from cover for Torsen differential 
(arrows). 
    
Note:  
Only mark location, if same driveshaft is go

Page 10 of 23

AUDI A6 1997 C5 / 2.G 01V Transmission Drive Shaft Service Workshop Manual 39-81
      
-  Remove mounting bolts for both driveshaft 
flanges. 
     
-  Remove upper three mounting bolts for each 
driveshaft constant velocity joint. 
     
-  Back off mounting bolts for cent
Page:   1-10 11-20 21-30 next >