AUDI A6 1997 C5 / 2.G 01V Transmission Select Lever Mechanism Manual PDF

37-66

Adjusting

- Place selector lever in position "P".

- Shift lever/shift lever to "P" (last position, shift
lock solenoid must engage).

- Slightly loosen mounting bolt at bracket to transmission.
Check freedom of stress of selector lever cable, if necessary
eliminate stress.
- Tighten mounting bolt of bracket to 23 Nm.
- Check shift mechanism page 37
-2 .
Pa
ge 71 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-67


Locking cable for shift mechanism
(without Tiptronic), removing and
installing

Note:
Removing:
Repair Manual, Body Interior, Repair Group 68;
storage compartments/paneling; removing storage bin on driver's side

Repair Manual, Electrical Equipment, Repair
Group 92; Steering column switches, servicing; Steering column switches, removing and installing

Locking cable must not be kinked.
- Disconnect Ground (GND) strap from battery.
- Remove driver-side storage compartment below
steering wheel.
- Remove steering column switch.
Pa
ge 72 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-68


- Set ignition/starter lock in "Drive" position.
- Shift selector lever into position "P".
- Lift up locking bracket -1- and pull locking cable
out of ignition/starter lock.
- Remove cover with guide (selector lever
mechanism) page 37
-5 .
- Unclip locking cable from securing spring at shift
mechanism housing, slightly lift up securing
spring to do so.
- Loosen cable tie -2- and remove locking cable.
Pa
ge 73 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-69


Installing and Adjusting
- Installation is the reverse of removal.
- Install locking cable without kinking and secure
at indicated position using cable tie -2-.
- Adjust steering column rearward/downward.
- Check locking mechanism of interior lever -1-.
- Slightly loosen bolt -6-.
- It must be possible to slide bracket -3- in
direction of arrow -5-.
- Make sure securing spring is correctly seated in
shift mechanism housing.
- Hook locking cable bracket -3- into shift
mechanism and locking coupling ring in lever (for
locking cable).
Pa
ge 74 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-70


- Connect 3352A adjustment pin for shift lock 3 -
item 4- between lever (for locking cable) and
locking coupling ring.
- Pull locking cable in direction of arrow -5- and
tighten bolt -6- to 8 Nm.
- Check locking cable after every new adjustment
of the locking cable page 37
-1 .
Pa
ge 75 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1