display AUDI A6 1997 C5 / 2.G AEB Engine Readiness Codes

01-59


Readiness code

Readiness code, checking


Note:
The readiness code will be erased:

When Diagnostic Trouble Code (DTC) memory
is erased
When the Engine Control Module (ECM)
harness connector is disconnected (e.g. to
connect VAG 1598/22 test box)
When the battery is disconnected

Required special tools and test equipment
VAG 1551 Scan Tool (ST) with adapter cable
VAG 1551/3

Checking

- Connect VAG 1551/ VAG 1552 Scan Tool (ST)
and press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with ignition
switched on) Page 01
-7 .
Rapid data transfer
HELP

Indicated on display
Pa
ge 1 of 22 Readiness code
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-60

Read Measurin
g Value Block
HELP
Input display group number XXX

Indicated on display
- Press buttons -0-, -8- and -6- to input display group number 86, and
press -Q- button to confirm input.
Read Measurin
g Value Block 86

1
2
3
4

Indicated on display (1-4 display fields)
Note:
The readiness code is generated as soon as only zeros ("0") are shown in
display field 1. - Check readiness code values in display field 1.
Specified value: 00000000
-
Press button to advance program sequence.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -6- to select "End Output" function 06, and press
-Q- button to confirm input.
Pa
ge 3 of 22 Readiness code
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-61
If the readiness code was not generated,
generate readiness code again Page 01
-62
.

- Check readiness code Page 01
-59
. If DTC
memory has been erased, or ECM has been
disconnected from B+, generate readiness code
again Page 01
-62
.
Explanation of 8-digit readiness code Readiness code is generated only when all display values = 0 1
2
3
4
5
6
7
8
Diagnosis
0 Three Way Catalytic Converter (TWC)
0 TWC heating (not applicable / always "0")
0 EVAP system and fuel tank leak detection test
0 Secondary Air Injection (AIR) system (not applicable / always "0")
0 Air conditioning system (diagnosis not applicable / always "0")
0 Oxygen Sensor (O2S) control
0 Oxygen Sensor (O2S) heating
0 Exhaust Gas Recirculation (EGR) system (not applicable / always "0")
Pa
ge 4 of 22 Readiness code
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-63

Step 1: Check DTC memory Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -2- to select the "Check DTC Memory" function
02, and press -Q- button to confirm input.
No DTC reco
gnized

Indicated on display
If one or more DTCs are stored:
If no DTCs were recognized: - Repair cause of malfunction.
- Erase DTC memory.
- Stop engine, start engine again, and road test.
- Check DTC memory again and erase.
-
Press button to advance program sequence.
Pa
ge 6 of 22 Readiness code
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-64

Step 2: Erase DTC memory Rapid data transfer
HELP
Select function XX

Indicated on display
Note:
When erasing DTC memory, the readiness code is also erased. - Press buttons -0- and -5- to select the "Erase DTC Memory" function
05, and press -Q- button to confirm input.
Rapid data transfer DTC Memor
y is erased

Indicated on display
-
Press button to advance program sequence.
Pa
ge 7 of 22 Readiness code
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-65

Step 3: Adaptation of throttle valve control
module to ECM Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measuring Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -6- and -0- to input display group number 60, and
press -Q- button to confirm input.
Read Measuring Value Block 60
1
2
3
4

Indicated on display (1-4 display fields) - Press -4- button to select "Basic Setting" function 04 (adaptation of
throttle valve control module to ECM)
System in Basic Setting 60
1
2
3
4

Indicated on display (1-4 display fields) - Check specified values in display fields 3 and 4:
Pa
ge 8 of 22 Readiness code
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-66


Display fields

1 2 3 4
Display group 60: Adaptation of throttle valve control module to Engine Control Module (ECM)
Display
xxx
xxx
Idle
Part throt.
Full throt.
Decel
Enrich ADP.runs
ADP. OK
ADP.ERROR
Indicated Throttle valve angle Throttle valve actuator angle Operational status Adaptation status
Specified value --- --- Idle ADP. OK
If "ADP. ERROR" is indicated in display field 4:

- Check DTC memory Page 01
-15
.
If the specified value "ADP. OK" is indicated in
display field 4:

-
Press button to advance program
sequence.
Pa
ge 9 of 22 Readiness code
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-68

Step 5: Oxygen Sensor (O2S) control
operating condition Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measuring Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -0- to input display group number 30, and
press -Q- button to confirm input.
Read Measuring Value Block 30
1
2
3
4

Indicated on display (1-4 display fields) - Increase engine speed to 1800-2200 RPM.
- Hold at 1800-2200 RPM until:

Specified value of "111" is reached in display field 1
Specified value of "110" is reached in display field 2
Pa
ge 11 of 22 Readiness code11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-69


Display fields

1 2 3 4
Display group 30: Oxygen Sensor (O2S) control operating condition
Display xxx xxx
Indicated Status of Heated Oxygen Sensor (HO2S), bank 1,
before TWC (B1-S1) Status of Heated Oxygen Sensor (HO2S), bank
1, after TWC (B1-S2)
Specified
value 111 110 ---
---


Evaluation Page 01
-70

Evaluation Page 01
-70


If the specified values are not indicated:

- Check DTC memory Page 01
-15
.
If the specified values are indicated in display
fields 1 and 2:

- Continue to hold engine speed at 1800-2200
RPM.
Pa
ge 12 of 22 Readiness code11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2

01-70

Explanation of 3-digit value in display fields 1
and 2

When display = 1
1
2
3

1 Oxygen Sensor (O2S) control active
1 Heated Oxygen Sensor (HO2S)
operational
1 Oxygen Sensor (O2S) heater ON

Note:
O2S control for bank 1 Oxygen Sensor (O2S)
after Three Way Catalytic Converter (TWC), B1-
S2), is not active at idle.
Pa
ge 13 of 22 Readiness code11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.01.2