28-44
Knock Sensor (KS) 2 -G66- (cylinder 3/4)
Harness connector
Terminal
VAG1598/31 test box
Socket
1 (signal) 107
2 (Ground -GND-) 99
3 (shielding) 108
- Repair open circuit or short circuit if necessary.
Pa
ge 48 of 59 I
gnition s
ystem, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.28.1
28-46
Component location Overview of component
locations Page 24
-5
The Camshaft Position (CMP) sensor provides
the ignition position for cylinder 1.
For failure, knock control is switched off and the
ignition angle is retarded slightly since a cylinder
allocation is no longer possible. In addition, the
boost pressure of the turbocharger is decreased.
Engine will continue to run without Camshaft
Position (CMP) sensor signal and can also be
restarted:
When a malfunction is recognized, the Engine
Control Module (ECM) initiates one ignition
spark per cylinder for each crankshaft rotation.
The offset of one engine rotation will have no
noticeable effect on the injection. Instead of
occurring with intake valves open, injection will
be "pre-loaded" (in front of closed intake valve).
This has only a minor effect on the quality of the
mixture preparation.
Pa
ge 50 of 59 I
gnition s
ystem, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.28.1
28-49
Checking Ground (GND) wire
If all specified values are being reached and the LED does not blink
(measured between terminal 1 and 2 with starter and connector
connected):
If specified values are not obtained:
Checking wire connections between Camshaft Position (CMP)
sensor and Engine Control Module (ECM) - Check following wire connection for open circuit and short circuit to B+:Harness connector
Terminal
Measure to
3 B+
- Repair open circuit or short circuit if necessary.
- Replace Camshaft Position (CMP) sensor.
- Connect VAG1598/31 test box at wiring harness to Engine Control
Module (ECM), do not connect ECM Page 24
-19
.
Pa
ge 53 of 59 I
gnition s
ystem, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.28.1
28-50
If, after erasing the DTC memory for a test, a DTC relating to the
Camshaft Position (CMP) sensor (hall sensor) is indicated again, even
though all previous tests were OK, the following malfunction is possible:
Repair Manual, 1.8 Liter 4
-Cyl. 5V Turbo Engine Mechanical, Engine
Code(s): AEB, ATW, Repair Group 15; Valvetrain, servicing
- Check following wire connections for open circuit and short circuit to
Ground (GND) and B+:
Harness connector
Terminal
VAG1598/31 test box
Socket
1 (B+) 98
2 (signal) 86
3 (Ground -GND-) 108
- Repair open circuit or short circuit if necessary.
Shutter wheel for Camshaft Position (CMP) sensor is not aligned
properly.
- Unscrew Camshaft Position (CMP) sensor and check whether shutter
wheel is mounted properly at camshaft (if mounted improperly, locking
lug will get squished when mounting bolt is tightened).
- If position of shutter wheel is OK, check allocation of
crankshaft/camshaft.
Pa
ge 54 of 59 I
gnition s
ystem, checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.28.1
