AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual A6 1998 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/1191/w960_1191-0.png AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual

Page 1 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-166
 
     
Drive pinion and ring gear, 
adjusting 
     
General notes:  
     
Drive pinion and ring gear must be very 
carefully adjusted to ensure long service life 
and smooth running. At the

Page 2 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual Make sure that all installation and measurement 
procedures are performed with the utmost care 
and cleanliness to ensure a successful result. 
Pa
ge 2 of 38 Drive 
pinion and rin
g gear, ad
justin
g

Page 3 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-167
 
  
Gear set, adjusting and marking
 
1 - 
Identification "0937" means the Oerlikon 
gear set with a ratio of 37: 9. 
2 - 
Pairing number (312) of gear set. 
3 - 
Dimension "r" is based on the

Page 4 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-168
 
  
R - Actual dimension between ring gear 
axis and face of drive pinion in position 
of quietest running for this gear set R = 
Ro + r 
Vo - Hypoid offset
Pa
ge 4 of 38 Drive 
pinion and rin

Page 5 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-169
      
Gear set, adjustment sequence
 
      If drive pinion and gear ring have to be adjusted, 
the following sequence is recommended for 
maximum efficiency:  
     
1.)   Determine total shi

Page 6 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-170
 Adjustment overview
 
Note:  
When working on transmission, drive pinion or gear set only need to be adjusted if components were replaced which directly 
influence the final drive. Note the fo

Page 7 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-171
 
  
Shim location
 
Note:  
Adjustment overview when replacing individual 
components of differential   page 39
-170
 . 
S1 - Adjustment shim for ring gear in final 
drive cover 
S2 - Adjustme

Page 8 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-172
 
  
Special tools and equipment  
 
VW382/10 extension pin
 VW385/1 measuring bar
 VW385/2 centering disc
 VW385/3 plastic piece
 VW385/14 measuring rod
 VW385/15 extension pin
Pa
ge 8 of 38 D

Page 9 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-173
 
  
 
VW385/17 magnetic plate
 VW385/30 master gauge-adjustable
 VW385/33 end gauge
 VW387 dial gauge holder
 VW388 measuring lever
 VW401 thrust plate
Pa
ge 9 of 38 Drive 
pinion and rin
g ge

Page 10 of 38

AUDI A6 1998 C5 / 2.G 01V Transmission Drive Pinion And Ring Gear Adjust Workshop Manual 39-174
 
  
 
VW402 thrust plate
 VW408A punch
 VW457 support channels
 VW521/4 locking sleeve for ring gear
 VW521/8 bushing for ring gear
 VW540 holding fixture
Pa
ge 10 of 38 Drive 
pinion and rin
Page:   1-10 11-20 21-30 31-40 40 next >