display AUDI A6 1999 C5 / 2.G AHA Engine Throttle Valve Control Module Checking User Guide

24-146
Evaluation of display group 3 Display
group: 3


Display field:
3
Possible malfunction cause
Corrective action
0.0
Open circuit or short circuit to B+ in signal wire between throttle position
sensor -G69- and engine control module
Malfunction in Ground for -G69-- Check wiring page
24
-147

99.0
Short circuit to Ground in signal wire between throttle position sensor -G69-
and engine control module
Malfunction in voltage supply for -G69-
Pa
ge 26 of 36 Throttle valve control module, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.2

24-151

Test procedure

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with ignition
switched on; engine not running) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -6- and -0- to input display group number 60 (060),
and press -Q- button to confirm input.
System in Basic Setting 60 1 2 3 4

Indicated on display (1-4 display fields)
Notes:
After confirming input of display group 60, adaptation is started. The
Throttle Position (TP)sensor is positioned in the closed throttle, wide
open throttle and limp-home positions. Following this procedure, other
intermediate steps will create a characteristic curve of the relationship
between Throttle Position (TP) sensor -G69- and angle sensor for
throttle drive -G187-. The Motronic ECM stores these values in permanent memory.
Afterward, the throttle valve assumes the starting position.
Pa
ge 33 of 36 Throttle valve control module, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.2

24-152

- Compare display with specified values (display
fields 1-4):

Display fields

1 2 3 4
Display group 60: Basic setting-throttle valve control module
Display
xxx
xxx
Idle
Part throt
Full throt
Decel
Enrich ADP runs
ADP. OK
ADP. ERROR
Indicates Throttle valve
angle Throttle drive
angle Operating
condition Adaptation condition
Range
0 - 90
--- --- ---
Specified
value 1 - 10
(automatic trans.)
1 - 20
(manual trans.) --- Idle ADP. runs

0 - 5
0 - 5
Idle ADP. OK
Pa
ge 34 of 36 Throttle valve control module, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.2

(ADP. ERROR indicates unsuccessful
adaptation)

If displayed values are NOT OK:
- Check DTC memory ( page 01
-16
)
- Check throttle valve control module ( page 24
-128
)
Pa
ge 35 of 36 Throttle valve control module, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.2

24-153

- End adaptation as soon as possible after 30
seconds by pressing button. If displayed values are OK:

- Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
input.
Pa
ge 36 of 36 Throttle valve control module, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.2