AUDI A6 1999 C5 / 2.G 01V Transmission Read Measuring Value Block E 17 Workshop Manual

01-187


Read Measuring Value Block
(scan tool function 08) for
transmissions with hydraulic
control -E17-

Note:
For transmissions with hydraulic control -E18/2-,
"Read Measuring Value Block" page 01
-228


WARNING!

To avoid accidents during measuring and test
drives, observe safety precautions page
01
-34
.

Procedure

- Connect VAS 5051 tester or V.A.G 1551 Scan
Tool (ST) and select Transmission Control
Module (TCM) using "address word" 02 page
01
-36
. Ignition must remain switched on.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press PRINT button to turn on ST printer. Indicator lamp in button must
light up.
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Pa
ge 1 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-188

Read measurin
g value block
Q
Enter display group number XXX

When indicated on display:
- Enter desired display group number, display group overview, page
01
-189
.
- Press Q button to confirm input.
Read measuring value block 1 1 2 3 4

Indicated on display (example) for display group 001:
Notes:
Explanation of values in the individual display fields Test table page 01
-194
.
Display can be printed out when printer is switched on.To switch to a different display group, proceed as follows:
Display group
V.A.G 1551
VAS 5051 tester
Higher Press button -3-
Press button.
Lower Press button -1-
Press button. -
If specified values are obtained in all display fields, press button.
Rapid data transfer
HELP
Select function XX

Indicated on display (function selection):
Pa
ge 2 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-189
Overview of selectable display group numbers for transmission with hydraulic control -E17- Indicated on display (example)

Display fields:
1 2 3 4
J J J
Display group no.
Display field
Description
Read measuring value block 1

0 RPM 0 RPM 0 RPM 4
001 1
2
3
4 Engine speed (RPM)
Sensor for Transmission RPM -G182-
Transmission Vehicle Speed Sensor -G38-
Driving range selected
Read measuring value block 2

0 0 % 0 RPM 4 002 1
2
3
4 Dynamic code number
Throttle valve value
Transmission Vehicle Speed Sensor -G38-
Driving range selected
Read measuring value block 3

PN active 0 km/h 12.8 V 003 1
2
3
4 Brake
"P" "N" lock
Speed
Supply voltage pin 54, 55
Pa
ge 3 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-190

Indicated on display (example)

Display fields:
1 2 3 4

Display group no.
Display field
Description
Read measuring value block 4

21.0 C P 1000
004 1
2
3
4 ATF temperature
Selector lever position
Multi-function switch position
On Board Diagnostic (OBD)
1) information
Request for engine intervention2)
Read measuring value block 5

0 0 0 4
005 1
2
3
4 Solenoid valve 1 -N88-
Solenoid valve 2 -N89-
Solenoid valve 3 -N90-
Driving range selected
Read measuring value block 6

0.747A 0.747A 0.747A 4 006 1
2
3
4 Specified current of solenoid valve 4 -N91-
Specified current of solenoid valve 5 -N92-
Specified current of solenoid valve 6 -N93-
Driving range selected
Pa
ge 4 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

1) Only for vehicles with CAN-bus. For information about which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, engine/transmission allocation, ratios, equipment

2) Only for vehicles without CAN-bus. For information about which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, engine/transmission allocation, ratios, equipment

Pa
ge 5 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-191

Indicated on display (example)

Display fields:
1 2 3 4

Display group no.
Display field
Description
Read measuring value block 7

21.0 C 0.747A TC on 0 RPM
007 1
2
3
4 ATF temperature
Specified current of solenoid valve 7 -N94-
Torque converter clutch
Torque converter slip speed
Read measuring value block 8

0 % 5 % 008 1
2
3

4 Kick down switch
Throttle valve value
Engine torque in Nm
1)
Throttle valve duty cycle in %
2)
Deceleration mode/engine under load
Read measuring value block 9

100 Nm 350 Nm 0 RPM 0%
009
1)
1
2
3
4 Engine torque (actual)
Maximum torque
Engine speed (RPM)
Throttle valve value
Pa
ge 6 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

1) Only for vehicles with CAN-bus. For information about which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, engine/transmission allocation, ratios, equipment

2) Only for vehicles without CAN-bus. For information about which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, engine/transmission allocation, ratios, equipment

Pa
ge 7 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-192

Indicated on display (example)

Display fields:
1 2 3 4

Display group no.
Display field
Description
Read measuring value block 9

100 Nm 0 RPM 0 % 0.00 ms
009
2)
1
2
3
4 Engine torque (actual)
Engine speed (RPM)
Throttle valve value
Fuel consumption signal
Read measuring value block 10

0,00 0 RPM 4
010 1
2
3
4 Torque increase in torque converter
Engine speed (RPM)
Gear selected
Anti-Slip Regulation (ASR)
Read measuring value block 11

D M-switch up button Compr. ON 011 1
2
3
4 Selector lever position
Tiptronic recognition
Tiptronic Switch -F189-
Air conditioning kick down
2) Only for vehicles without CAN-bus For information on which vehicles are equipped with CAN-bus
Pa
ge 8 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, engine/transmission allocation,
ratios, equipment

Pa
ge 9 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-193

Notes:

When the printer is switched on, the contents of
the display will be printed out on the scan tool
log.
If specified values are not obtained in all display
fields:

-
Press button.
Rapid data transfer
HELP
Select function XX

Indicated on display
Pa
ge 10 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13