transmission oil AUDI A6 2000 C5 / 2.G 01E Transmission Bearing House And Torsen Differential Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2000, Model line: A6, Model: AUDI A6 2000 C5 / 2.GPages: 38, PDF Size: 0.87 MB
Page 4 of 38
34-56
Removing
- Secure transmission on engine and transmission support VW 540.
- Place drip tray V.A.G 1306 underneath and drain transmission oil (2 oil
drain plugs).
- Remove release bearing, clutch release lever and guide sleeve
Page 30
-27
.
- Remove bearing housing (arrow) and pull off.
A - M8/M10 stud
Pa
ge 4 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, removi...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5
Page 22 of 38
34-73
- Slide follower -A- for 1st and 2nd gear onto selector rod and secure
with circlips.
- Oil all bearings of input shaft and drive pinion/hollow shaft in
transmission housing and bearing flange as well as selector rods with
gear oil.
Note:
When inserting the complete bearing plate, ensure that the selector rods
align with their mounting points. - Pry used seal for input shaft carefully out of transmission housing with
VW 681.
- Coat sealing surfaces between bearing plate and transmission housing
with sealing paste AMV 188 000 02 or AMV 188 001 02 sealing paste.
- Insert complete bearing plate into transmission housing.
Pa
ge 22 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, rem...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5
Page 34 of 38
34-85
- Install complete selector shaft.
- Screw locking bolts -A- for selector shaft into transmission housing.
- Aluminium and steel bolts must not be interchanged when installing.
Tightening torques: for aluminium locking bolts = 50 Nm, and for steel
locking bolts = 70 Nm.
- Lightly oil new O-ring for cover for selector shaft and fit.
- Fit cover for selector shaft.
- Apply sealing paste AMV 188 000 02 to bolts -B- (Qty. 3) before
installing and tighten.
- Slide Torsen differential onto splines of hollow shaft.
Parts catalog - Press Torsen differential in direction of arrow, and measure distance
between top edge of bolted end cover and front edge of outer race of
ball bearing for Torsen differential.
- Determine required shim(s) from following table.
Pa
ge 34 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, rem...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5
Page 38 of 38
34-88
- Remove protective hose.
- Install release bearing, clutch release lever and
guide sleeve from Page 30
-27
.
- Check that transmission can be shifted through
all gears.
- Fit connecting rod.
- Check oil level in transmission Page 34
-39
.
Pa
ge 38 of 38 Bearin
g housin
g, Torsen differential, end cover, internal selector mechanism, in
put shaft, drive
pinion and hollow shaft, rem...
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.5