AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual A6 2000 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/1210/w960_1210-0.png AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual

Page 1 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual 00-27
 
     
Servicing, notes 
      The maximum possible care, cleanliness and 
proper tools are essential to ensure satisfactory 
and successful transmission repairs. The usual 
basic safety precau

Page 2 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual      
Thoroughly clean all connections and the 
surrounding area before disconnecting. 
     Check installation dimension of torque 
converter before installing transmission   page 32
-8 
Pa
ge 2 of 1

Page 3 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual 00-28
      
When installing transmission, make sure 
centering sleeves are correctly seated. 
     Place parts that have been removed on a clean 
surface and cover. Use foils and paper. Use 
lint-fre

Page 4 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual Always replace O-rings, gaskets and sealing 
rings. 
     After removing gaskets and seals, always 
inspect the contact surfaces at housing or shaft 
for burrs resulting from removal or for other 
sig

Page 5 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual 00-29
      
Thoroughly clean housing joint surfaces before 
assembling and apply sealing compound AMV 
188 200 03. 
    
Before installing, fill gap between sealing lips (arrow) of radial-shaft 
seal

Page 6 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual 00-30
      
Nuts, bolts  
     
Loosen bolts in reverse order of tightening 
sequence. 
     Tighten and loosen bolts or nuts for securing 
covers and housings without tightening 
sequence in diagona

Page 7 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual      
Do not over-stretch circlips.
     Always replace damaged or over-stretched 
circlips. 
     Circlips must be fully seated in grooves.
    
Replace roll pins. Installation position: Slot is long

Page 8 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual 00-31
      
Mounts  
     
Install needle bearings with the lettering on the 
bearing (the side with thicker metal) facing the 
drift. 
     Insert bearing with transmission oil or ATF, 
depending on

Page 9 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual Heat tapered roller bearing inner races to 
approx. 100 5C before installing. Press in to 
stop so that there is no axial play. 
     
Shims  
     Measure shims at several points using a 
micrometer.

Page 10 of 10

AUDI A6 2000 C5 / 2.G 01V Transmission Service Notes Workshop Manual 00-32
      
Valve body  
     
Replace valve body if shift members are 
burnt. 
     The valve body is allocated to the transmission 
code letters   parts catalog. 
     
Guided Troubleshooting, Vehi