engine AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual A6 2000 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/1316/w960_1316-0.png AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual

Page 1 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-18
 
     
Transmission, removing and 
installing 
     
Removing  
     
Special tools, testers and auxiliary items 
required:   
    
Engine-/Transmission lifter V.A.G 1383 A
    
Transmission su

Page 3 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-20
      
-  Obtain radio code on vehicles with coded 
radio. 
     
-  With ignition switched off disconnect battery 
Ground strap. 
    
-  Loosen bolts (arrows) and remove engine cover panels (a

Page 5 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-22
 
    
-  Unscrew two bolts securing heat shield -2- on exhaust pipe (right and 
left). 
-  Unscrew nuts -3- on exhaust pipe (right and left).
-  Unscrew engine/transmission securing bolts acces

Page 10 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-27
 
    
Note:  
Avoid excessive bending of the flexible pipe connection (decoupling 
element) on the front exhaust pipe. The angle between the catalytic 
converter and the front exhaust pipe must

Page 11 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-28
 
    
Note:  
The two hex socket head bolts M 10 x 60 must be replaced by new hex 
bolts M 10 x 55 (Part No. N 104 684 01) so that the two bolts (arrows) can 
be tightened with a torque wrench

Page 14 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-31
      
-  Remove all but one of the engine/transmission 
securing bolts from below (one bolt is left in 
place to hold engine and transmission together). 
    
Note:  
If transmission support 32

Page 16 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-33
      
Installing  
      Installation is carried out in the reverse order, 
when doing this note the following:  
     
-  Always replace all seals and gaskets.
     
-  Always replace all self

Page 17 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-34
      
-  On vehicle with V6 bi-turbo engine, fit 
intermediate plate on dowel sleeves on engine 
flange. 
    
-  Two hex socket head bolts M 10 x 60 must be replaced by new hex 
bolts M 10 x 5

Page 19 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-36
 
    
Vehicles with 6-cyl. bi-turbo engine  
Dowel sleeves -A- for aligning.  1) The two hex socket head bolts M 10 x 60 must be replaced by new hex 
bolts M 10 x 55 (Part No. N 104 684 01) so

Page 20 of 21

AUDI A6 2000 C5 / 2.G 01E Transmission Remove And Install Workshop Manual 34-37
      
Component  
  
Nm  
Clutch slave cylinder to transmission 
1)  
20  
Transmission support to transmission   40  
Engine speed sender -G28-      10  
Drive axle to drive flange   M8  
M10
Page:   1-10 11-20 next >