wheel AUDI A6 2001 C5 / 2.G 01V Transmission Remove And Install Workshop Manual

37-73

Additional information

Repair Manual, Suspension, Wheels,
Steering
Repair Manual, Electrical Equipment
Repair Manual, Engine Mechanical

- Note radio code (for vehicles equipped with
coded anti-theft radio).

- Disconnect Ground (GND) strap from battery.

For 6 cylinder gasoline engines except for 2.7
Liter 5V turbo engine:

- Remove engine cover (arrows).
Pa
ge 3 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-76

- Mount 10-222A/3 adapter for spindle at front of
support.

All: - Install 10-222A engine support bridge with 10-222A/1 brackets and
support engine/transmission in this position.
- Take up weight of engine/transmission assembly on spindles.
- Tighten the rear spindle less, to enable later lowering at rear.
- Raise vehicle.
- Remove front wheels.
Pa
ge 6 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-77


- Remove sound-deadening pan.

Repair Manual, Suspension, Wheels, Steering, Repair Group 40
- Remove left and right heat shields for drive axles (arrows).
- Disconnect drive axles from transmission drive flanges.
Pa
ge 7 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-82

All-wheel-drive vehicles

Repair Manual, Engine Mechanical, Repair Group 26; removing and
installing exhaust system. - Remove heat shield -A- above driveshaft.
- Remove rear part of exhaust system if necessary:- Remove heat shield -2- for driveshaft from cover for Torsen differential
(arrows).

- Unbolt driveshaft from transmission and hang or support.
Pa
ge 12 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-83

Continuation for all vehicles

Use 3282/19 adjustment plate to position the 3282 transmission support
for Automatic Transmission 01V.
The symbols on the adjustment plate indicate the necessary mounts and
the arrow points toward front of vehicle. - Position 3282 transmission support.

Automatic Transmission 01V with All Wheel Drive is supported at the
same positions as the Front Wheel Drive version. - Roll VAG1383A engine/transmission hoist with 3282 transmission
support under transmission and support transmission.
- Align adjustment plate parallel to transmission.
- Secure transmission on 3282 transmission support using bolt -A-.
- Remove left and right transmission support with transmission mount
page 37
-125

Pa
ge 13 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-89

Installing

Installation is reverse of removal, noting the
following:
Before installing:

All-wheel-drive vehicles

- Clean threads in driveshaft flange!

Continuation for all vehicles

- Clean ATF lines page 37
-158
.

- Insert torque converter into transmission page
32
-8 .

WARNING!

Check installation dimension of torque
converter before installing transmission
page 32
-8

- Make sure bushings are correctly seated.

Note:
If the bushings get stuck in the transmission
housing, they must be removed and new
bushings must be installed on the engine.
Pa
ge 19 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-94

For 6 cylinder TDI engines

Continuation for all vehicles
Note:
Some bolts also have a bracket or a Ground (GND) connection attached
refer to tightening torque tables starting page 37
-119
onward. - Check whether brace -B- is still swung to side (arrow direction) before
installing the transmission.
- Install connecting bolts for engine/transmission.

Repair Manual, Engine Mechanical, Repair Group 26; removing and
installing exhaust system.
Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing
- Install multi-function Transmission Range (TR) switch -F125-.
- Slightly raise engine/transmission subframe at rear via VAG1383A
hoist.
- Install remaining connecting bolts for engine/transmission.
- Install front exhaust pipes:
- Install subframe, observe tightening sequence and alignment with
master hole.
Pa
ge 24 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-95

- Only perform vehicle alignment if necessary.

Repair Manual, Suspension, Wheels,
Steering, Repair Group 44; Vehicle alignment


- Install transmission supports at left and right with
transmission mount page 37
-125


Bolt torque converter to drive plate
For vehicles with hex bolts: - Remove bolt -A- after transmission is bolted to engine.
- Apply corrosion protection to contact surface between bolt -A- and oil
pan.

- Bolt torque converter to drive plate via 3 bolts using special tool V175
(turn crank shaft an additional 1/3 turn every time).
Pa
ge 25 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-96
For vehicles with Torx bolts:

Repair Manual, Electrical Equipment, Repair Group 27; Starter,
removing and installing
- Bolt 3 torque converter bolts to drive plate using respective Torx insert
(turn crank shaft an additional 1/3 turn every time).
- Install starter.
- Install ATF lines to engine/transmission subframe.
- Install bracket for ATF- line.
- Slightly raise engine/transmission subframe at rear via VAG1383A
hoist.

Repair Manual, Suspension, Wheels, Steering, Repair Group 40
- Bolt in engine speed (RPM) sensor -G28- (arrow -B-) at front left of
transmission (if installed).
- Connect connector for speedometer Vehicle Speed Sensor (VSS).
- Bolt drive axles to transmission flanges.
Pa
ge 26 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-97


- Bolt in bolts at mounting bracket of selector lever cable, install selector
lever cable and if necessary, adjust.

All-wheel-drive vehicles - Connect connector of multi-function Transmission Range (TR) switch -
1-.
- Connect connector for transmission wiring harness and secure using
securing lever -2-.
- Install shielding plate/selector lever cable
- Bolt driveshaft to transmission flange page 39
-79
, Driveshaft,
removing and installing.
Pa
ge 27 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2