wheel AUDI A6 2012 Manual Online

• Move select or lever to p osition P q ,& .
• If you are towing a trailer, unhitch the trail­
er from your veh icle.
• Take the
jack and the spare t ir e out of the
luggage compartment
q page 257,
q page 257.
A WARNING
You or your passengers cou ld be injured
while changing a whee l if you do not fol­
low these safety precautions:
- If you have a f lat t ire, move a safe dis­
tance off the road. Turn off the eng ine,
turn the emergency f lashers on and use
other warning devices to alert o ther mo­
torists.
- Make su re that passengers wait in a safe
pla ce away from the ve hicle and well
away from the road and traffic.
- T o help preven t the veh icle from mov ing
sudden ly and possibly slipping off the
jack, always fully set the parking brake
and block the whee l diagonally opposite
the wheel being changed . When one
front wheel is lifted off the ground, plac­
ing the Automat ic Transm iss ion in "P"
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the ground is level and fi rm. If necessa ry,
use a sturdy board under the jack.
- After installing the spa re wheel, make
sure that you replace the flat tire/whee l
in its sto rage area properly and tighten
the kn u rled re taining screw securely.
Changing a wheel
When you change a wheel, follow the se­
quence described below step-by-step and in
exa ctly that order .
-
1. Remove the decorati ve wheel cov er* . For
mo re deta ils see also
Q page 260, Deco­
rative wheel covers
o r q page 260,
Wheels with wheel bolt caps.
2 . Loosen the wheel b olts q page 260.
What do I do now? 259
3. Locate the proper mounting point for the
4.
5.
6.
7.
8.
9 .
jack and align the jack below that point
q page 261.
Raise the car with the jack q page 261.
Remove the wheel with the flat tire and
then insta ll
th e spare c> page 262.
Tighte n all wheel bolts lightly.
Lower the vehicle wi th the jack.
U se the wheel bolt w rench and
firmly
t ighten a ll wheel bolts q page 260 .
Replace the decora tive wheel co ver*.
A WARNING
A lways read and fo llow all WARNINGS and
informat ion¢
& in Raising the vehicle on
page 261
and r::> page 263.
After changing a wheel
A wheel change is not complete without the
doing the following .
• Replace the too ls and the jac k in their prop­
er locat ion .
• The fault whee l wi ll not fit inside the spare
wheel well. Store it in the luggage compart­
ment and secure it so that it does not slide
r::>page 59.
• Check the tire pressure on the spare wheel
immed iate ly after mounting it.
• As soon as possib le, have the
tightening
torqu es
on all wheel bolts c hec ked with a
t o rque wrenc h. The co rrec t tighte ning tor­
que is
90 ft lb (120 Nm).
• Have the flat tire
replaced as soon as possi ­
b le.
(D Tips
- I f you not ice that the wheel bo lts a re
corroded and difficult to turn while
changing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked. ..,_
•
•

260 What do I do now?
-After changing a wheel, the tire pressure
i n a ll four ti res must be checked/cor rect­
ed and t he tire pressure mo nitor ing indi ­
cator m ust b e stored in the MMI
Q page255 .
Decorative wheel covers
Applies to vehicl es: with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 189 Chan ging a w hee l: R em ovin g the whee l cove r
Removing
.. Inse rt the
hook (provided with the ve hicle
tool kit) in the hol e in the wheel hub cove r .
.. Pull off the
decorative wheel cover
c> fig. 189.
Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts with caps
The caps must b e removed first from the
wheel bol ts before the bol ts can be u n­
s cre wed.
Fig . 19 0 Chang ing a w hee l: remov ing t he w heel bo lt
caps
Removing
" Push the
plastic clip (provide d w ith the ve­
hicle too l ki t) over the w heel bo lt ca p un til the inner
reta iners on the clip a lign with t he
edge of the cover .
.. Remove the cap with the
plastic clip (veh i­
cle tool kit)
c> fig. 190.
Refitting
.. Pla ce t he caps over t he whee l bolts and
push them back o n.
T he cap s are to pro te ct and kee p the w heel
b olts clean .
Loosening and tightening the wheel
bolts
T he wheel bol ts mu st be loosened befo re rais ­
ing the vehicle .
Fig. 191 Cha ng ing a w heel: loosenin g th e w hee l bol ts
Loosening
.. Slide the
wheel wrench ont o the wheel bo lt
as far as it w ill go.
.. Take tight hold of the
end of the wrench
ha ndle a nd turn th e wheel bo lts
counter­
clockwise
about on e single tu rn in the dire c­
tion of ar row
c> fig. 191.
Tightening
.. Slide the wheel wrenc h onto the wheel bolt
as far as it w ill go .
" Take tig ht hold of the
end of the wr ench
ha ndle a nd turn each wh eel bo lt
clockwise
until it is seate d .
.8_ WARNING
- Do n ot u se forc e or hurry whe n ch ang ing
a w heel -yo u can ca us e the vehicle to sli p
off the jack and ca use ser io us pe rso nal
i njur ies.

-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury.
@ Tips
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts.
- If a whee l bolt is very tight, you may find
it easier to loosen by carefully push ing
down on the end of the wheel bolt
wrench with
one foot only. As you do so,
hold on to the car to keep your ba lance
and take care not to slip.
Raising the vehicle
The vehicle must be lifted with the jock first
before the wheel con be removed .
Fig. 1 92 Changing a w hee l: mou nting po ints fo r the
jack
F ig . 19 3 Close -up: proper positioning of jack
.. Engage the parking bra ke to prevent your
vehicle from rolling un intentionally.
.. Move the
selector le ver to position P .
.. Position the jack below the door sill under
the
mounting point that is closest to the
wheel to be changed¢
fig. 192.
What do I d o now ? 261
.. Extend the jack under the lifting point on
the door sill until its arm is positio ned di­
rectly under the lifting point ¢,&. .
.. Align the jack so that its arm@¢
fig. 193
engages in the designated lifting point in
the doo r si ll and the movable base @ lies
flat o n the ground. The base @ must be
ver­
tical
under th e lifting point @.
.,. Wind the jack up fu rther until the f lat t ire
comes off the gro und ¢ ,&. .
The jack mus t be installed
only at the places
i ndicated ¢
fig. 192. The re is exactly one loca­
tion for each wheel. The j ack mus t not be
pos it ioned at any other location ¢
&.
An unstable surfac e under the jack ca n cause
the ve hicl e to slip off the jack. Always provide
a firm base for the ja ck on the g ro und . If nec­
essary p lace a sturdy board or sim ilar support
u nder the jack . On
hard, slippery surface s
(such as tiles) use a rubbe r mat or similar to
prevent the jack from slipping
¢ & .
A WARNING
- You or your passengers co uld be in jured
while c hanging a wheel if you do not fo l­
low these safety precautions:
- Positioning the j ack under the vehicle
at any o ther place than those indicate d
above may damage the vehicle or may result in persona l injuries .
- A soft o r uns table surf ace unde r the
j ac k may cause the veh icle to slip off
the jack. Always provide a f irm base for
the jack on the ground. If necessary, u se a st urdy board under the jack.
- On hard, slippery surface (such as ti les)
use a rubber mat or similar t o prevent
the jack fr om slipping .
- To help prevent injury to yo urself and
your passengers:
- Do not ra ise the veh icle until you are
s ur e the jack is securely engaged .
- Passe ngers must not remain in the ve­
h icle when i t is ja cke d up.

262 What do I do now ?
-Make sure that passengers wait in a
safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then continue to ra ise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.
Taking the wheel off/installing the spare
Follow th es e ins truc tions st ep-by-st ep for
changing the wheel.
F ig . 194 Chan gin g a w hee l: us ing t he sc rew drive r han ·
die (w ith t he bla de re moved) t o tu rn the b olts
Fig. 195 Chang ing a w hee l: alignm en t pin insid e t he
to p hole
Aft er you h ave loosened all wheel bol ts and
ra is ed the veh icle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwd riv ·
er handle to comp lete ly remove the top­
mos t wheel bo lt and set it as ide on a
clean
surface ¢ fig . 194 .
.. Screw the threaded end of the alignment
pin from the too l kit hand-tig ht into the
empty bolt hole
r::;, fig. 195.
.. Then remove the other whee l bolts as de­
scrib ed above.
.. Take off the whee l leaving the a lignment
pin in the bolt hole
¢ 0) .
Putting on th e spar e wheel
.. Lift the spare wheel and carefully s lide it
over the alignment pin to g uide it in place
¢ (D .
.. Use the hexagonal socket in the sc rewd river
handle to screw in and tig hten all whee l
bolts
slightly .
.. Remove the a lignment pi n and insert and
tighten the rema in ing wheel bolt slightly
like the rest .
.. Turn t he jack hand le co unter -cloc kwise to
lowe r the veh icle un til the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly
r::;, page 260 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposi te one, to keep the
wheel cen tered.
(D Note
When remov ing or installing the whee l,
the rim cou ld hit the brake rotor and dam·
age the rotor . Work carefu lly and have a
second pe rson help you .
@ Tips
Never use the hexagonal socket in the han­
d le of the screwdriver to loosen or tighten
the wheel bolts.
- Pull the revers ible blade from the screw·
dr iver before you use the hexagonal
sock et in the hand le to turn the w heel
bolts.
- Whe n mount ing tires w ith unidirectional
tread design make sure the tread pat·
t er n is po inted the right way
r::;, page 2 63.
- T he wh eel bolts s hou ld be cl ean and easy
t o tu rn . Chec k for dirt and corrosion on
t he m ating surfaces of bot h the wheel
an d t he hub . Remove all d irt from these
surfaces befo re remounting the whee l.

Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire w ith a tread p attern
int ended fo r use in a specific dir ection
When us ing a spare tire w ith a tread pattern
in tended for use in a specific direction, please
note the following:
- The direction of rotation is marked by an ar­
row on the side of the tire .
- If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the ti re will not be able to
achieve its optimum performance character­
i st ics with rega rd to aquaplaning, noise and
wear.
- We recommend that you pay particular at­
tent ion to this fact du ring wet weathe r and
that you adjust your speed to match road conditions.
- Replace the flat tire w ith a new one and
have it installed on your veh icle as soon as
possib le to restore the handling advantages
of a unid irectiona l tire .
Notes on wheel changing
Please read the info rmation c:> page 246 , New
t ires and replacing tires and wheels
if you are
going to use a spare t ire which is different
from the tires on your veh icle.
After you change a tire :
-Check the tir e p re ss ure on th e spare imme­
di ately after in st a ll at ion.
- Have th e wheel bol t ti ghtenin g torqu e
ch ecked with a torque wrench a s soon a s
possible b y your autho riz ed Audi dealer o r
a qu alified ser vic e statio n.
- With ste el a nd alloy wheel rims , the wheel
bolts a re correctl y tightened at a torque of
90 ft lb (1 20 Nm ).
- If yo u n otice that the wheel bolt s are cor­
r oded a nd d ifficult to tu rn whil e changi ng
a t ire, the y should be replaced before you
chec k the t igh tening to rque. What do I do now? 263
- Repla ce the flat ti re w ith a new one and
h av e it i nsta lled on you r veh icle as s oon as
po ssible. Remount the whe el cov er.
Un til th en, d riv e with extr a care and at re­
duc ed sp eeds.
A WARNING
-
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were factory installed, then be sure to read the information¢
page 246,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
pa rtment and are not loose in the pas­
senger compartment .
- In an accident or sudden maneuver they
could fly forward , injuring anyone in the
veh icle.
- Always sto re damaged wheel, jack and
too ls se curely in the luggage compa rt­
ment. Otherwise , in an accident or su d­
den maneuver they could f ly forward,
causing injury to passengers in the vehi­
cle.
•
•

2 7 4 General information
General information
Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::> page 2 76. This sec ·
tion provides general information, notes and restrictions which apply to this data .
Vehicle identification
The key data is given on the vehicle identifica·
tion number (VIN) plate and the vehicle data
sticker.
Fig. 209 Veh icle Ide ntific atio n Number (VlN) p late: lo­
cation on driver 's sid e das h panel
Fig. 210 Th e vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
b le from the outside through the windshield
r:::> fig . 209. You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select: Function button
ICAR ! > Car sys­
tems
> VIN number . The
vehicle identification label
is located in the luggage compartment in the
spare wheel wel l.
The label¢
fig. 210 shows the following vehi­
cle data :
(D Production control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo·
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War·
ranty
& Maintenance booklet.
The safety compliance sticker
is you r assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
time the vehicle was manufactured . You can
find this sticker on the left door jamb.
It
shows the month and year of production and
the ve hicle ident ification number of your vehi ·
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carr ier .
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are Listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oi l and coolant, plus maximum load, wh ich in·
eludes passenger weight (lSO lbs/68 kg per
Ill>

276 Data
Data
211 hp, 2.0 liter 4-cylinder engine
Applies to vehicles: with 2.0 liter 4-cylinder engine and front-wheel drive
Engine data Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio
Fuel
Dimen sion s (appro x.)
Leng th (with license pla te bracket)
Width (across mirrors) He igh t (unloaded) hp@rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm)
211 @4300 -6000
4
121 (1984)
3.65 (92 .8)
3 .25 (82.5)
9.6: 1
Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details
¢ page 215,
Gasoline
in (mm) 1 93.9 (4925)
in (mm) 82.l (2086)
in (mm) 57.8 (1468)
Turning circle diameter (curb to curb) ft . (m) 39.0 (11.9)
Capacities (appro x.)
Fuel tank
- Total capacity
- Reserve (o f to tal capacity)
Windshield fluid container
Wind shield and headlight wa sher
fluid containe r*
Engine oil with filter c hange gal (liters)
19
.8 (75 .0)
gal (liters) 2 .6 (10.0)
quarts (liters) 3 .7 (3 .5)
q uarts ( li1ters) 5 .2 (4 .9)
quarts (liters) 4 .9 (4 .6)

Data
310 hp, 3.0 liter 6-cylinder engine
Applies to vehicles: with 3.0 liter 6-cylinder engine and all-wheel drive
Engine data
Maximum output SAE ne t
Maximum torque SAE net
No. of cylinders
Displacement
Stroke
Bore
C ompression ratio
Fuel
Dimensions (approx .)
L eng th (wit h license pl ate brac ket)
Width (across mirrors) He igh t (unloaded)
310@ 5500-6500 hp@ rpm
lb-ft@ rpm
-.. .--
C ID (cm3
)
in (mm)
in (mm)
__ ,
-~-- ,
325 @ 290 0-4500
6
182 (2995)
3.50 (89.0)
3 .33 (84.5)
10.3: 1
Premium unleaded (91 AKI) Recommended for maxi­
mum engine performance. Further details¢
page 215,
Gasoline
in (mm) 193.9 ( 4925)
in (mm) 82.1 (2086)
in (mm) 57 .8 ( 1468)
Turning circle diameter (curb to curb) ft. (m) 39.0 (11.9)
Capacities (appro x.)
Fuel tank
- Total capac ity
- Reserve (o f to tal capacity)
Windshield fluid container
Windshield and headlight washer
fluid container *
Engine oil with filter change gal (liters)
19.8 (75.0)
gal (li
ters) 2. 6 (10.0)
quarts (liters) 3.7 (3.5)
qu arts ( liters) 5 .2 ( 4.9)
quarts (lite rs) 7.2 (6.8)
277
•
•

complexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, safe ty and e nvir onm en tal con­
cerns p lace very strict limits on the na ture of
repairs and adjustments to engine and trans ­
miss io n pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing dev ices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure prope r
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliability
of your vehicle and even void your vehicle war­ ranty. The refo re, p roof of servici ng in accord­
ance w ith the maintenance sched ule may be a
condition for upholding a poss ible war ranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, crea ting unnecessary risks for you
and your passengers.
If in doubt about any servicing, have it done
by your authorized Audi dealer or any other
properly equipped and q ualified workshop .
We strong ly urge you to give you r a uthorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and trained spec ialists to keep your vehicle
running properly .
Performing limit ed m aintenance you rself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
your vehicle with ordinary too ls, should the
need arise and trained personnel be unavaila­
b le. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given . Always rigorously obse rve the
WARNINGS provided .
Before you check anything in th e engine
compartment, a lway s re ad and heed all
Con sumer In formation 2 79
WARNINGS ¢ & and ¢ & in Working in the
engine comportment on page 220 .
A WARNING
-Ser ious personal injury may occur as a re­
sult of improperly performed mainte­ nance, adjustments or repa irs.
-Always be extremely careful when work­ ing on the vehicle. Always follow com­
mon ly accepted safety pract ices and gen­
eral common sense . Never r isk personal
lnJU ry .
- Do not attempt any of the ma intenance ,
checks or repairs descr ibed on the fol­
lowing pages if you are not fully fam iliar
wit h these or othe r pro cedures with re­
spect to t he veh icle, or are uncerta in how
to p roceed .
- Do not do any work without the proper
too ls and equipment. Have the necessary
work done by your authorized A udi deal ­
er or another proper ly equipped and
qualified workshop .
- The engine compartment o f any motor
veh icle is a potentially hazardous area.
Never reach into the area around or
touch the rad iator fan. It is temperature
contro lled and can switch on suddenly -
even when the engine is
off . The radiator
fan switches on automat ically when the
coo lant reaches a certai n temperature
a nd will cont inue to run until the coo lan t
temper ature drops.
- Always sw itch
off the ignition before any­
one gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work under­
neath the vehicle . The j ack s upplied with
the vehicle is not adequate for this pur­
pose and cou ld co llapse causing serio us
personal i njury .
-If you must work unde rneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are a lways securely
blocked and that the engine cannot be
started.
•
•

A
Accessories .... ...... ..... .. .. .. ... 280
AC (automatic climate control) ... .. .. .. 66
AC (climate contro l) . . . . . . . . . . . . . . . . . . 64
Adapt ive cruise control . . . . . . . . . . . . . . . . 78
C lean ing sensors/c ameras .. .. .. .. .. . 206
M essages . . . . . . . . . . . . . . . . . . . . . . . . . 85
Request for driver intervention . . . . . . . . 82
Stop-and-go traffic .... ... .. .. .... .. 81
Adapt ive Lig ht (defective) ... .. .. .. .. .. 2 2
Adding Eng ine coolant .............. ... ... 228
Eng ine oi l ..... ....... .... ... ... .. 225
W indshield was her fl uid ... .. .. .. .. . 234
Addit ives
Eng ine oi l
225
Ad justi ng
Air distribution (automatic climate con-
trol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
a ir distribution (cl imate control) . .. .. .. 64
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 50
Instrument illum inat io n .... ... ... ... 44
Steer ing colum n electrically .. .. .. .. .. 69
Steer ing colum n manually . .... .. .. .. 69
Temperatu re (automat ic climate co ntrol) 67
Tempera tu re (clima te con trol) .. .. .. .. 64
Ai rbag system . . . . . . . . . . . . . . . . . 142, 163
Advanced Airbag System . ...... ... .. 146
Advanced A irbag System components . 150
Ca re . .. .. .. ................. .. .. . 158
C hi ld ren . .. .. ........... .. .. .. ... 170
C hild restra ints . .. ..... ... .. .. .. ... 170
Components (front airbags) . ... .. .. . 150
Danger of fitting a child seat on the front
passenger seat . . . . . . . . . . . . . . . . . . . . 144
Disposal . .. ............. .... .. .. . 158
Front airbags . . . . . . . . . . . . . . . . 146, 148
H ow do the front airbags work? . ..... 152
H ow many airbags does my vehicle
h ave? . .. .. .. ............. .. .. ... 150
H ow t he Advan ced Airbag Sys tem com-
ponents wor k toge ther .... .. .. .. .. . 15 2
I mpor tan t safety instructions on the
knee airbag system .... ... .. .. .. .. . 16 1
Important things to know . . . . . . . . . . . 142
K nee airbags .. ........... .. .. .. ... 159
Mo nitoring . ............. .... .. .. . 154
Inde x 283
PASS ENGER A IR BAG OF F light ... .. .. 155
Repairs ... .. .. .... . ... ...... ... .. 158
•
Safety instr uctions . .. .. ..... ... .. .. 157 •
Side a irbags . .. .. ................. 162
S ide curtain airbags ... ............. 165
Warning/ind icator lights ........... .. 18
Warning/Indicator lights ...... ... .. 154
When must the system be inspected? . 154
A ll-wheel drive .. .. .... ........... .. 193
Winter tires ... .. ................. 250
A lloy whee ls .. .... .. . .. .. ..... ... .. 209
Alte rnato r . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Ambience lighting . ................. . 44
An ti-free ze
refer to E ng ine coolant . ..... ... .. .. 227
Anti- lock b rak ing system ..... ... ... .. 189
Wa rning/ind icator lights ........... .. 19
Anti-slip reg ulation ............. .. .. 189
An ti-the ft systems
El ectronic i mmob i Lizer . . . . . . . . . . . . . . . 31
Asht ray ...... .. .... .......... ...... 54
Audi braking guard
refer to brak ing guard .............. . 78
Audi drive selec t
refer to drive select .. ... .... ... .. .. . 95
Audi Se rv ice Repair Manuals and Litera-
tu re ....... .. .. .. ... ............ .. 278
A UTO
automat ic climate control . . . . . . . . . . . . 67
Automa tic head lights ............. .. 41
cli mate control . . . . . . . . . . . . . . . . . . . . . 64
Auto Lock .. .... .. .................. 32
A utomat ic be lt re tractor ......... .. .. 136
Automat ic car wash .. .............. . 205
Automatic climate control Air vents .... .. ...... ............. . 67
Automat ic recirc ulation ......... .. .. . 68
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 66
Setup .. .. .. .. .... .. .. ...... ...... 68
synchronizing . . . . . . . . . . . . . . . . . . . . . . 67