change time AUDI A6 2013 Owner's Manual

The location of the brake fl uid reservo ir can be
seen in the engine compartment illustration
c::> page227.
The fl uid level may drop slightly after some
time due to the automatic adjustment of the
brake pads. This is not cause for alarm .
If the brake fluid level falls considerably be­
l ow the "MIN" mark, the bra ke wa rning/ind i­
cator light
1111 (U .S . models)/ . (Canadian
models) will come on
c::> page 15. Do not con­
tinue to operate the vehicle. The comp lete
brake system sho uld be thoroughly checked
by an author ized Audi dealer or other quali­
fied fac ility and the cause corrected . If the
brake fluid level is too low, the brake warn ing/
i ndicator light w ill illuminate . Contact an au­
thor ized Audi dealer
imm ediately .
Changing brake fluid
Have the brake fluid changed by an experi­
enced technician .
Brake fluid absorbs moisture from the a ir. If
the water content in the brake fluid is too
h igh, corrosion in the brake system may result
after a per iod of t ime . The bo iling po int of t he
brake fluid w ill also decrease consider ably and
dec rease b raking per formance.
Therefore, the brake flu id must be changed
ever y two years . Always use new b rake fluid
whi ch confo rms to Fede ral Motor Vehicle
Standard "FMVSS 1 16 DO T 4".
The brake flu id rese rvoir ca n be difficult to
r eac h, therefo re , we re commend that yo u
have the brake fl uid changed by y our autho r­
i z ed
Audi dealer . Your deale r has the correct
too ls, the right brake fluid and the know -how
to do this for you .
A WARNING
-Brake fluid is po isonous . It must be stor­
ed only in the closed orig inal container
out of t he reac h of children!
- Brake fa ilure can result from old o r inap ­
propr iate brake fluid. Observe these pre­
caut ions:
Checkin g and fillin g 235
-Use only brake f luid that meets SAE
spec ificat ion
J 1703 and conforms to
Federal Motor Ve hicle Standard 116.
Always check with your autho rized Audi
dealer to make sure yo u are using the
correct brake fluid . The correct type of
brake f lu id is also ind icated on the
brake flu id rese rvoi r.
- The bra ke fluid must be new. Heavy us e
of the brakes can cause a vapo r lock if
the b ra ke fluid is left i n the system too
l ong . This can se riously affec t the effi ­
ciency of the b rakes as well as your
safety . This co uld resu lt in an accident.
(D Note
B rak e fluid wi ll damage the pa int o f you r
vehicle .
~ For the sake of the environment
Because o f the p rob lem of pro per disposal
of bra ke fluid as well as the spe cial too ls
r equired an d the necessary exper tise, we
r ecommend that yo u have the brake flu id
changed by yo ur authorized Aud i dea le r.
Battery
General information
U nder normal ope ra ti ng cond itions , the bat­
te ry in yo ur Audi doe s not need any ma inte ­
nance. With
high outside tempera tures or
l ong daily drives we recommend that you have
the e lectrolyte level checked by a service fa­
c ili ty. The electrolyte leve l should a lso be
checked each t ime the battery is charged
c:> page 237.
Have the battery checked when yo u take your
vehicle in for service. You are well advised to
replace a batte ry that is older than 5 years .
Wi th certain types of airbag deployment, the
battery is disconnected from the vehicle elec­
trical system for safety reasons
c> & in Re­
pair , care and disposal of the airbags on
page 161.
~
•
•

-Always wear gloves and eye protection.
Do not tilt the battery because acid
could leak out of the ventilation open­
ings .
- If you get battery acid in your eyes or
on your skin, immediately rinse with
cold water for several minutes and get
medical attention.
- If you should ingest any battery acid,
seek medical attention immediately.
- Do not expose the battery to an open
flame, electric sparks or an open light .
- Do not smoke.
- Do not interchange the positive and neg-
ative cables .
- When working on the battery, be sure
not to short-circuit the terminals with
tools or other metal objects. This would cause the battery to heat up very quickly,
which could lead to damage or explosion
and personal injury .
- When a battery is charged, it produces
hydrogen gas which is explosive and
could cause personal injury .
- Always keep the battery well out of the
reach of children .
- Before work is done on the electrical sys­
tem, disconnect the negative ground ca­
ble.
- Before performing any work on the elec­ trical system, switch off the engine and
ignition as well as any electrical equip­
ment. The negative cable on the battery
must be disconnected.
If you are just go­
ing to replace a light bulb, then it is
enough to switch off the lights.
- Before disconnecting the battery , switch
off the anti-theft alarm system! Other­
wise you will set off the alarm.
- When disconnecting the battery, first
disconnect the negative cable and then
the positive cable.
- Before reconnecting the battery, make
sure all electrical consumers are switch­
ed off. Reconnect the positive cable first
and then the negative cable. Never inter­
change the cables - this could start a fire!
Checking and filling 237
- Never charge a frozen or a thawed-out
battery . It could explode! If a battery has
frozen, then it must be replaced. A dis­
charged battery can freeze over at 32 °F
(0 oc).
-Make sure the vent hose is always attach­
ed to the opening on the side of the bat­
tery .
- Never use batteries which are damaged.
There is the danger of an explosion! Al ­
ways replace a damaged battery .
A WARNING
California Proposition 65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive problems . Wash hands after han­
dling .
(D Note
-Do not disconnect the vehicle battery
when the ignition is on or when the en­
gine is running, otherwise, you will dam­
age electronic components in the electri­
cal system.
- If your vehicle is going to stand for a
long period of time without being driven,
protect the battery from "freezing", oth­
erwise it will be damaged and will then
have to be replaced.
Battery charging
Start ing the engine requires a well charged
battery.
Fig . 189 Eng in e compart ment : co nnecto rs for a charg ·
e r and jump st art cable s
1111>

Battery replacement
The new battery must have the same specifi­
cations and dimensions as the original equip­
ment battery.
Intell igent energy management in your vehi­
cle is respons ible for d istributing the electri­
cal energy throughout your vehicle
~ page 197. The intel ligent energy ma nage­
ment system w ill keep the eng ine batte ry
charged be tte r than vehicles w ithout t his sys­
tem . To make sure the additional e lectrical en ­
ergy is available once again after you have
changed the battery, we recommend that you
install batteries of the same type and man u­
facture only (the same as those installed at
the time your vehicle was delivered). Specifi­
cations a re listed on the battery hous ing . Your
author ized dealer must code the battery in
the energy management system to enable you
to use the energy managemen t fu nctions co r­
rectly a fter replacing the battery .
The new battery must have the same capacity,
voltage (12-vo lts), a mperage, construct ion
and p lug sealing.
When installing the battery , make sure the ig ­
n ition and all e lectr ica l cons umers are sw itch­
ed off.
CD Note
Make sure the ventilation hose on the s ide
of the battery is connected, ot herwise
fumes or battery ac id can leak out.
- Vehicles with the Start-Stop-System* are
equipped with a specia l cycle-proof AGM
batte ry. Insta lling a different type of
batte ry can c ause prob lems in the vehi­
cle electrical system . When rep lacing the
vehicle battery, always insta ll one with
the same specifications as the original battery.
@ For the sake of the environment
Because of the problem of proper disposa l
of a battery, we recommend your author­
ized Aud i dea ler change the battery for
you. Batter ies contain sulf uric ac id and
Checkin g and fillin g 239
lead and must always be disposed o f prop ­
erly in compliance with a ll environmental
regulations. Disposing of vehicle batter ies
i mproperly is very dangerous to the envi­
ronment.
Windshield/headlight
washer container
Fi g. 1 90 Engine compar tment: cover on th e windshield
and headl ig ht* washe r flu id reservo ir
The washer fluid conta iner is marked w ith the
symbol ~ on its cap
~ fig . 190, ~fig. 184.
... Before you check anything in the engine
compartment,
always r ead and heed all
WARNINGS ¢ _& in Working in the engine
compartment on page 225.
... Lift the fil le r cap tongue to add washer flu­
id. You can fi ll the containe r to the top.
... Press the cap back onto the fi lle r neck after
filling the container.
You can find the reservo ir
cap acit y in the table
in
¢ page 282.
Clean water should be used when filling up. If
poss ible, use soft wa ter to prevent scaling on
washer jets . Always add a g lass cleaner solu­
tion (with frost protection in the winter).
CD Note
Do not mix engine coo lant antifreeze or
any o ther additives to fill up t he wind­
sh ield washer reservoir .
•
•

242 Tire s and wheels
Groove
means the space between two adjacent tread
ribs .
Load rating (code)
means the maximum load that a tire is rated
to carry for a given inflation pressure. You
may not find this informat ion on all tires be­
cause it is not req uired by law.
Maximum load rating
means the load rating for a t ire at the max i­
mum permissible inflation pressure for that
tire.
Maximum loaded vehicle weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity we ight, and
(d) Production options weight
Maximum (permissible) inflation pressure
means the maximum cold inflation pressure
to which a tire may be inflated. Also called
"maximum inflation pressure ."
Normal occupant weight
means 150 lbs. (68 kilograms) times the
number of occupants seated in the vehicle up
to the total seating capacity of your vehicle .
Occupant distribution
means distribution of occupants in a vehicle.
Outer diameter
means the overa ll diameter of an inflated new
tire.
Overall width
means the linear distance between the exteri­
ors of the sidewalls of an inflated tire, includ­
ing elevations due to labeling, decorations, or
protective bands o r ribs .
Ply
means a layer of rubber-coated parallel cords.
Production options weight
means the combined weight of those insta lled
regular production options weighing over 5
lbs. (2.3 kg) in excess of those standard items
which they replace, not previously considered
in curb weight or accessory we ight, including
heavy duty brakes, ride levelers, roof rack,
heavy duty battery, and special tr im .
Radial ply tire
means a pneumat ic tire in which the ply cords
that extend to the beads are laid at substan­
t ia lly 90 degrees to the center line of the
tread .
Recommended inflation pressure
see<=> page 241, Cold tire inflation pressure.
Reinforced tire
means a t ire design to operate at higher loads
and at h igher inflation pressures than the cor­
responding standa rd tire. Reinforced tires
may be identified as "XL" "xl" "EXTRA LOAD"
' ' '
or "RF" on the sidewa ll.
Rim
means a metal support for a tire or a tire and
tube assembly upon which the tire beads are
seated.
Rim diameter
means nom inal d iameter of the bead seat. If
you change your wheel s ize, you will have to
purchase new tires to match the new rim di­
ameter.
Rim size designation
means r im diameter and width .
Rim width
means nominal distance between rim flanges.
Sidewall
means that portion of a tire between the
t read and bead.

When the malfunction indicator is illuminat­
ed, the system may not be able to detect or
signal low tire pressure as intended. TPMS
malfunctions may occur for a variety of rea ­
sons, including the installation of replace­ ment or alternate tires or wheels on the vehi ­
cle that prevent the TPMS from function ing
properly . Always check the TPMS malfunction
tellta le after replacing one or more tires or
wheels on your vehicle to ensure that the re­
placement or alternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
Fig. 196 Display : underinflatio n warning
Fig. 197 Display : Syste m malfun ctio n
Using the ABS sensors, the tire pressure moni ­
toring system compares the tire tread circum­
ference and vibration characteristics of the in­
dividual tires . If the pressure decreases in one
or more tires , th is is indicated in the instru­
ment cluster with a warning symbol
RE and a
message
¢fig . 196.
The tire pressure monitoring system must be
reset via MMI each time the pressures are ad-
Tires and wheels 259
justed (e.g. when switching between partial
and full load pressure) or after changing or re­
plac ing a tire on your vehicle¢
page 260. The
TPMS indicator only monitors the tire pres­
sure that you have previously stored. You can
find the recommended tire pressures for your
vehicle on the label on dr iver's side B-pillar
~page 244.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if :
- the tire pressure in one or more tires is too
low,
- the tire has structural damage,
- the tire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
¢page 260.
Warning symbols
RE Loss of pressure in at least one tire¢.&. .
Check the tire or tires and replace or repair if
necessary. The indicator light
RE in the instru­
ment cluster also illuminates
¢ page 12.
Check/correct the pressures of all four tires
and reset TPMS via MMI.
11;;~, ( T ire Pressure Monitoring System) Tire
pressure! System malfunction.
If11NIS, appears after switching the ignition
on or while driving¢
fig. 197 and the indica­
tor light
RE in the instrument cluster blinks
for approximately one minute and then stays
on, there is a system malfunction.
Attempt to store the correct tire pressure
¢
page 260 . If the indicator light does not
turn off or if it turns on shortly thereafter, im­
mediately drive your vehicle to an authorized
Audi dealer or authorized repair facility to have the malfunction corrected .
A WARNING
-If the tire pressure ind icator appears in
the instrument cluster display, one or
more of your tires is significantly under­
inflated. Reduce your speed immediately
and avoid any hard steering or braking
maneuvers. Stop as soon as possib le and .,.

296 Index
K
Key ... . ... ... .. .. ..... ... .. .. .... .. 3 1
Battery rep lacement master key ... .. . . 32
Emergency key . . . . . . . . . . . . . . . . . . . . .
3 1
Key not recognized ............ .. .. .. 74
Key replacement . . . . . . . . . . . . . . . . . . . 31
Master key . . . . . . . . . . . . . . . . . . . . . . . . 31
M echanical key .............. ... ... . 32
Valet key . . . . . . . . . . . . . . . . . . . . . . . . . .
31
K ick-down
tiptronic
110
K nee airbags .... .. ..... ... .. .. .... . 162
Descr ipt ion .... . ...... ... .. .. .... . 162
How they work . .. ..... ... .. .. .... . 164
Important safety instructions . . . . . . . . 164
L
Lane assist . . . . . . . . . . . . . . . . . . . . . . . . . 9 1
Lane Change Ass istant
refer to side ass is t ...... .. .. .. .. .. . .
LATC H
.. .. .. ............. .... .. ...
D . t· escnp ion .... .... .... .. .. .. .. .. .
Install ing a child restraint ...... .. .. .
L ocat ion .. .... ............. ... ' . .
M ount ing and releasing the an cho rage
hook
. . .. .. ............. .... .. .. .
94
185 186
187
186
187
Launch Contro l Program . ... .. .. .. .. . 110
Leather ...... .. .. ..... ... .. .. .... . 216
Leather (clea ning) .......... .. .. .. .. . 2 17
Leaving home ............. .. .. .. .. .. 43
Lift ing jack . .. .. .. ..... ... .. .. .... .
266
Lift ing vehicle
Light 278
Ambience lighting .......... .. .... .. 44
Com ing/Leaving home ..... .. .. ...... 43
Daytime running lights .. ... ... .. .. ..
41
Emergency flashers . . . . . . . . . . . . . . . . . 42
E t . l' h . x enor 1g ting .. .. .. .. .. .. .. .. .. .. 41
H ead lig ht range con trol ... .. .. .. .. . . 41
H igh beam .............. ........ .. 43
L ow beam . ... . .. ..... ... .. .. .... ..
4 1
Rear fog lights . .. ..... ... .. .. .... .. 41
Side ma rker lights ... ... .. .. .. .... .. 4 1
Turn signa ls ............. .. .. .. .. .. 43 Li
ght/ rain sensor
Hea dlights . ..... .. ... ..... ... .. .. .
41
Intermittent (w indshie ld w ipers) ... .. . 46
Sensor defective . . . . . . . . . . . . . . . . . . . . 22
Loa ding the roof ra ck ................ . 60
Locking
Power loc king switch .............. ..
36
Remote cont ro l . . . . . . . . . . . . . . . . . . . . 34
U si ng the key ................. .....
36
Low beams . .... .. ... .......... .... . 41
Lower universal anchorages (Cana da) 185
Luggage compartment
Cargo ne t . . . . . . . . . . . . . . . . . . . . . . . . .
62
En larging . .... .. ... .......... .... . 61
Load ing ... .... .. ... .. ..... ... .. .. . 61
Ski sack ... .... .. ... .. ..... .... . .. . 63
Stowing luggage ... ... ..... ... .. .. 132
Tie -downs . . . . . . . . . . . . . . . . . . . . . . . . . 62
Lumbar suppo rt
F ron t seats . . . . . . . . . . . . . . . . . . . . . . . .
52
M
Maintenance .... .. ............. .... 2 85
Malfunction Ind icator Lamp (MIL) . . 21, 29
Manual shift program .... ..... ... .. .. 109
Massage function
Front seats . . . . . . . . . . . . . . . . . . . . . . . .
52
Matte finish paint .. ............. .... 210
Mechan ica l key .... ... .. ..... ... .. .. . 32
Mir ro rs
Adjusting the exter ior m irrors ....... ..
48
d' . 1mming .... .. .. ... .......... .... . 48
Vanity mir rors . .. ............. .. ... 45
Monito ring the Advanced Airbag System 157
Multif unction steering whee l .. .. .. .. .. . 24
mult itro nic® 105
N
Natura l leather .. .. ................ . 216
New tires and whee ls
N HT SA
Co nta cting 251
13 4
Night vis ion assistant .... .. ... ..... .. 101
Cleaning came ra le n s ........ ...... . 211
Number of seats . .. ... .......... .. .. 136

It has always been Audi's policy to continu­
ously improve its products. Aud i, therefore,
reserves the right to make changes in design
a nd specifications, and to make additions or
improvements in its p roducts, without incur­
ring any obl igat ion to insta ll t hem on p rod­
uc ts p revio usly man ufact ured .
Text , illustrat ions and specif ications in th is
manual are based on the most up-to-date in­
formation available at the time of p rinting.
All rights reserved. May not be reproduced or
translated in whole or in part without the wr
itten consent of AUDI AG. Specifications are
subject to change without notice.
"Audi", "q uattro" and the four r ings emblem
are registered trademarks of AUD I AG.
Editor ial de adlin e: 08 /2 7/ 2012
@ For the sake of the environment
Printed on environmentally friendly pape r
(b leached without chlorine, recyclable).
Printed in Germany
© 2012 AUDI AG