door lock AUDI A6 ALLROAD 1999 C5 / 2.G Pneumatic Suspension System
[x] Cancel search | Manufacturer: AUDI, Model Year: 1999, Model line: A6 ALLROAD, Model: AUDI A6 ALLROAD 1999 C5 / 2.GPages: 44, PDF Size: 2.47 MB
Page 30 of 44
30
The driving speed signal …
... is a square-wave signal produced by the
dash panel, the frequency of which is
changed in accordance with the vehicle
speed.
... is required in the evaluation of the driving
condition (stationary/driving mode) and
thereby for selection of the control criteria
(see “Control concept”).
The interface for the driving speed signal is
redundant, as the information regarding
speed is also transmitted by the CAN bus.
K wire
Communication for self-diagnosis between
control unit J197 and the diagnostic tester
takes place via the familiar K wire by means of
conventional data messages.
The self-diagnosis K wire must not be
confused with the K wire connecting
operating unit E281 to control unit J197.
Power supply to the headlamp range control
system
In the case of 4-level air suspension in the
allroad quattro, the headlamp range control
system voltage is supplied by the air
suspension control unit J197. Further
information can be found under Control unit
J197 on page 34.
Additional interfaces
The door contact signal …
... is an earth signal from the control unit for
central locking. It indicates that the door or
boot lid/tailgate is open.
... serves as a “wake-up pulse” for transfer
from sleep mode to run-on mode (see
“Control concepts”).
Terminal 50 signal...
... signals actuation of the starter and is used
to switch off the compressor during start-up.
If a low position is detected following a wake-
up pulse, the compressor is activated
immediately in order to allow the vehicle to
drive off as quickly as possible.
The compressor is switched off during start-
up in order to save battery power and ensure
starting power.
The vehicle locking signal …
... is used as information for parking level
control
... is an earth pulse coming from the control
unit for central locking J429
... is not detected by the self-diagnosis.
Parking level control is not performed if this
signal fails.
Interfaces
The vehicle locking signal is not
required for vehicles without parking
level control (see pages from 10
onwards and 34 onwards).
Page 33 of 44
33
Key to function diagram
E281 Self-levelling suspension operating
unit
F216 Contact switch for switchable rear fog
light
G76 Self levelling suspension sender, RL
G77 Self levelling suspension sender, RR
G78 Self levelling sender, FL
G289 Self levelling suspension sender, FR
G290 Compressor temperature, self-
levelling suspension sender
G291 Self-levelling suspension pressure
sender
J197 Self-levelling suspension control unit
J403 Relay for self-levelling suspension
compressor
J429 Control unit for central locking
J431 Control unit for headlamp range
control
N111 Discharge valve for self-levelling
suspension
N148 Valve for FL suspension strut
N149 Valve for FR suspension strut
N150 Valve for RL suspension strut
N151 Valve for RR suspension strut
N311 Valve for self-levelling suspension
pressure accumulator
K134 Self-levelling suspension warning
lamp
V48 Left headlamp range control motor
V49 Right headlamp range control motor
V66 Self-levelling suspension compressor
motor= Input signal
= Output signal
= Positive
= Earth
= Bi-directional
= CAN bus/signal wire
Auxiliary signals:
CAN low
CAN high
Door contact signal
Diagnostic connector for K wire
Vehicle locked signal
Trailer operation signal (F126)
Terminal 50 signal
Driving speed signal
Terminal 56
Diagnostic connector for K wire
to the instrument cluster
Driving speed signal from ABS control unit,
speed sensor output, rear left
1
2
3
4
5
6
7
8
I
II
III
IV
Terminal 58s
Terminal 58d
ESP button
ESP button
A
B
C
DHeadlamp range control signal
9
Power supply J431
10