wheel bolts AUDI A7 2014 Owners Manual

256 Tire s and wheel s
T up to 118 mph (190 km/h)
U up to 124 mph (200 km/h)
H up to 130 mph (210 km/ h)
V up to 149 mph (240 km/h)
1l
Z over 149 mph (240 km/h)ll
W up to 168 mph (270 km/h)ll
Y up to 186 mph (298 km/h)l)
Your veh icle is norma lly fac to ry equipped with
tires , which possess excellent driving charac­
teristics and give yo ur Audi opt imum driving
comfort . An e lectronic speed limit er
c:> page 31 wi ll normally prevent your vehicle
from go ing faster th an the tire speed rating
c:> & .
U.S . DOT Tire Identification Numb er (TIN )
a nd tire manufacture d ate
This is the t ire's "serial number". It begins
with the letters "DOT" and indicates that the
tire meets all federal standards . The next two
numbers or letters indicate the p lant whe re it
was manufactured, and the last four numbers r epresent the week and year of manufacture.
F or example, the numbers 2213 mean the ti re
was p roduced in the 22nd week of 2013. The
other numbers are marketing codes that may
or may not be used by the ti re manufacturer .
T his informat ion is used to contact consumers
if a tire defect requires a recall.
Aud i Original tire
Tires wi th the ident ification "AO" or "RO" have
been specially matched with your Audi . We
recommend using only these tires because
they meet the highest standards regard ing
safety and driving character istics when used
correctly . Your authorized Audi dealer will
gladly prov ide you with more information .
Tire ply composition and materials u sed
The number of p lies ind icates the number of
layers of rubber-coated fabric in the t ire. In
general, the greater the number of plies, the mo re weight a tire can support . Tire ma nufac -
ll F t· "t h . or ires w 1 a m ax im um s pee d ca pabil ity ove r
1 4 9 mp h (240 k m/h) , t ir e m anufa ctur ers somet imes
use the letters " ZR."
turers also must indicate the mate rials in the
tire, which incl ude stee l, nylon, po lyester, and
others .
Maximum Load Rating
Th is number ind icates the maximum load in
k ilog rams and po unds that can be carr ied by
the tire .
Tire quality grading for treadwear,
traction , and temperature resistance
Tre ad wear, traction and tempera ture grades
c:>page 257 .
Maximum Permissible Inflation Pressure
This number is the greatest amount of a ir
pressure tha t should ever be put in the tire
u nder norm al driv ing cond it ions .
_& WARNING
= -
-Using incorrect or unmatched tires and/
or wheels or improper tire and wheel
combinations can lead to loss of control
coll is ion and serio us personal in jury.
'
- Always use ti res, rims and whee l bolts
that meet the specifications of original factory-insta lled tires or other comb ina­
tions that have been specifically ap­ proved by the vehicle manufacturer.
- Tires age even if they are not being used
and can fai l sudden ly, especially at hig h
speeds . Tires that are more than 6 years
old can only be used in an emergency
and then w ith specia l care and at lower
speeds.
- Ne ver mo unt used tir es on your veh icle if
you are not sure of the ir "p revio us histo­
ry." O ld used tires may have been dam­
aged even thoug h the damage cannot be
seen that can lead to sudden tire fa ilure
and loss of vehicle control.
- All fo ur whee ls must be fitted with radial
tires of the same type, size (rolling cir­ cumference) an d the same tread pattern . ..,_

The speed rating letter code (c::> page 246) is
on the side wall of the tire
c::> page 254.
A WARNING
Winter tires have maximum speed limits
that may be lower than your vehicle's max­
imum speed . Always know the maximum
speed before driving off. Never drive faster
than the speed permitted for your specific
winter tires . This will cause damage to the
tires leading to an accident and serious
personal injury to you and your passen­
gers.
A WARNING
Driving faster than the maximum speed
for which the winter tires on your vehicle
were designed can cause tire failure in­ cluding a blowout and sudden deflation,
loss of control, crashes and serious per­
sonal injuries . Have worn or damaged tires
replaced immediately.
- Winter tires have maximum speed rating
that may be lower than your vehicle's
maximum speed .
- Never drive faster than the speed for
which the winter or other tires installed
on your vehicle are rated .
A WARNING
Always adjust your driving to the road and
traffic conditions. Never let the good ac­
celeration of the winter tires and all-wheel
drive tempt you into taking extra risks . Al­
ways remember :
- When braking, an all-wheel drive vehicle
handles in the same way as a front drive
vehicle.
- Drive carefully and reduce your speed on
icy and slippery roads, even winter tires
cannot help under black ice conditions.
@l For the sake of the environment
Use summer tires when weather condi­
tions permit. They are quieter, do not wear
as quickly and reduce fuel consumption.
-
Tires and wheels
Snow chains
Snow chains may be fitted only to the front
wheels , and only to certain tire sizes. Ask your
authorized Audi dealer on which tire sizes
snow chains can be used.
If you are going to use snow chains, then you
must install them on the front wheels at
least.
The snow chains must have low-profile links
and must not be thicker than 0.4 inch
(10,S mm) , including the lock.
Remove wheel center covers and trim discs
before putting snow chains on your vehicle
c::> (]) . For safety reasons cover caps must then
be fitted over the wheel bolts. These are avail­
able from authorized Audi dealers.
A WARNING ,..__
Using the wrong snow chains for your vehi­
cle or installing them incorrectly can in­
crease the risk of loss of control leading to
serious personal injury.
- Snow chains are available in different
sizes . Always make sure to follow the in­
structions provided by the snow chain manufacturer .
- When driving with snow chains never
drive faster than the speed permitted for
your specific snow chains .
- Always observe local regulations.
(D Note
- Remove snow chains before driving on
roads not covered with snow to avoid
damaging tires and wearing the snow
chains down unnecessarily.
- Snow chains, which come into direct con­
tact with the wheel rim, can scratch or
damage it. Therefore, make sure that the
snow chains are suitably covered . Check
the position of the snow chains after
driving a few yards and correct if neces­
sary. Follow the instructions from the
snow chain manufacturer when doing so.
- If the Adaptive Air Suspension* should
malfunction, do not mount or use snow ..,.
259
•
•

260 Tire s and wheel s
chains because the vehicle will be ex­
tremely low. If you do drive with snow
chains on while the vehicle is at this lev­
el, the snow chains might severe ly dam­
age the wheelhouse and other parts of
the veh icle.
(D} Tips
Where snow chains are mandatory oncer­
tain roads, this normally also applies to
veh icles with all-wheel dr ive.
Wheel bolts
Wheel bolts must always be tightened to the
correct torque .
The design of whee l bolts is matched to the
factory installed r ims. If different rims
are fit­
ted, the correct wheel bolts with the right length and correctly shaped bolt heads must
be used. This ensures that wheels are fitted
secure ly and that the brake system functions
correctly .
In certain circumstances, you may not use
wheel bolts from a different vehicle -even if it
is the same mode l
¢page 287.
_& WARNING
Imprope rly tig htened o r maintained whee l
bolts can be come loose ca using loss of
contro l, a co llision and serious persona l in­
jury.
- Always keep the wheel bol ts an d the
threads in the wheel hubs clea n so the
wheel bolts can tu rn easily and be prop­
er ly tightened .
- Never grease or oil the wheel bo lts and
the threads in the wheel h ubs. They can
become loose w hile driving if greased or
oiled, even if tightened to the specif ied
torque.
- Only use wheel bolts that belong to the rim being installed.
- Never use different whee ls bolts on your
vehicle.
- Always maintain the correct tighten ing
torq ue for the wheel bo lts to reduce the risk of a whee
l loss. If the tightening tor­
que of the wheel bolts is too low, they
can loosen and come out when the vehi­
cle is mov ing. If the tighte ning torque is
too high, the wheel bolts a nd threads
can be damaged and the whee l can be­
come loose.
([) Note
The specified torque for the whee l bolts is
90 ft lb (120 Nm) with a tolerance of± 7,4
ft lb(± 10 Nm). Torque whee l bolts diago­
nally. Afte r changing a whee l, the torque
must be checked as soon as possible wi th a
torque wrench -pre ferably by an au thor­
ized Audi dealer or qualified workshop .
Low aspect ratio tires
Your Audi is factory-equipped with low aspect
ratio tires. These tires have been thoro ughly
tested and been se lected specifically for your
model for their superb performance, road fee l
and hand ling u nder a var iety of d riv ing condi ­
t ions . As k your author ized Audi dealer for
more details.
The low aspect ratio of these tires is ind icated
by a numeral of
55 or less in the tire's s ize
designation . The numeral rep resents the ratio
of the t ire's s idewa ll height in relation to its
t read width ex pressed in percentage. Conven­
t iona l tires have a he igh t/w idth rat io of 60 or
more.
The performanc e of low -a sp ec t-ratio tires i s
pa rticularly sensitive to improper inflation
pre ssure . It is therefore important that low
a spect ratio tires are inflated to the specified
pre ssure and that the inflation pressure i s
regularly checked and maintained. Tire pre s­
sures should be checked at least once a month and always befo re a long trip
¢ page 249, Checking tire pressure .
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damaged more
easily by impact w ith potholes, curbs, gull ies .,..

264 What do I do now?
What do I do now?
Emergency warning
triangle
App lies to vehicles: with emerge ncy warning triangle
The warning triangle is located on the inside
of the trunk lid .
-
"' M ~ 0 6
~ ~
Fig. 207 Tr unk lid: Warning triang le
.,. To open the cover , turn the locking mecha­
nism and pull the cover downward .
" m
.,. Remov e the warning triang le from its hold­
er.
The rear lid is only designed to hold the warn ­
ing triangle offered by the original accessories
program. If you would like to retrofit your ve­
hicle with a warning triangle, p lease contact
your authorized Audi dealer.
Vehicle tool kit
Vehicle tool kit and jack
The vehicle tool kit is located in the luggage
compartment under the cargo floor cover.
Fig. 208 Lu ggage compartme nt: cargo floor cover
folded upward/spa re t ire
Fig. 209 Trunk lid: Veh icle tool kit
.,. Fold the floor to the seatback with the help
of the handle .
.,. Turn the handwheel counter-clockwise
~ fig. 208 and remove the spare t ire to
reach the vehicle tool kit.
The onboard tool k it includes:
- Hooks to remove the wheel covers*
- Plastic hook to remove wheel bolt covers*
- Wheel bolt wrench
-Alignment pin for changing wheels
- Screwdriver with reversible blade
- Towing loop
-Jack
Before storing the jack, make sure it is wound
back down as far as it will go.
A WARNING
Improper use of the vehicle jack can cause
serious pe rsonal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts can­
not attain the necessary tighten ing tor­
que if you use the hex head, potentially
causing an accident .
- The factory-supplied jack is intended on­
ly for your vehicle model. Under no cir­
cumstances sho uld it be used to
lift
heavy veh icles or other loads; you risk in­
juring yo urself.
- Never start the engine when the vehicle
is raised, which could cause an accident.
- Support the vehicle securely with appro­
p riate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potential risk for injury. .,.

266 What do I do now?
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang ­
ing a wheel .
... After you experience a tire failure, pull the
car well away from moving traffic and try to
reach
level ground before you stop o ,&.
... All passengers should leave the car and
move to a safe location (for instance, behind
the guardrail)
o A-
.. Engage the parking brake to prevent your
vehicle from rolling unintentionally
o ,&.
... Move selector lever to position Po ,& .
• If you are towing a trailer, unhitch the trailer
from your vehicle .
... Take the
jack and the spare tire out of the
luggage compartment
o page 264,
o page265.
A WARNING
You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
- If you have a flat tire,
move a safe dis­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
sudden ly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed . When one
front wheel is lifted off the ground, plac­
ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm.
If necessary,
use a sturdy board under the jack.
-
-Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
opage 136.
@ Tips
Before changing the whee l, you must acti­
vate the jacking mode, so that the auto­
matic controls for the Adaptive Air Sus­
pension* do not make it more difficult to
lift the vehicle with the jack
o page 268 .
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order.
l. Activate the vehicle jack mode*
opage 268 .
2. Remove the decorative wheel cover* . For
more details see also
o page 267, Deco­
rative wheel covers
or o page 267,
Wheels with wheel bolt caps.
3. Loosen the wheel bolts o page 268.
4. Locate the proper mounting point for the
jack and align the jack below that point
opage 268.
5. Raise the car with the jack o page 268.
6. Remove the wheel with the flat tire and
then install
the spare opage 270.
7. Tighten all wheel bolts lightly .
8.
Lower the vehicle with the jack .
9 . Use the wheel bolt w rench and
firmly
tighten all wheel bolts o page 268.
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode * in the
MMI:
I CARI function button > (Ca r)* sys­
tems
control button > Servicing & checks
> Air susp.: jack mode > Off.
The vehicle jack mode* switches off automati­
ca lly at speeds above 6 mph (10 km/h) .
A WARNING ,-
Always read and follow all WARNINGS and
in format ion
o .&. in Raising the vehicle on
page 269
and opage 271.

After changing a wheel
A wheel change is not complete without the doing the following .
• Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment
Q page 136.
• Check the tire pressure on the spare wheel
immediately after mou nting it.
• As soon as possible, have the
tightening
torques
on al l wheel bolts checked with a
torque wrench. The correct tightening tor­
que is 90 ft lb (120 Nm).
• Have the flat tire
replaced as soon as possi­
ble.
(D Tips
- If you notice that the wheel bolts are
corroded and difficult to turn wh ile
changing a tire, they should be replaced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
- After changing a wheel, the tire pressure
i n all four tires must be checked/correct­
ed and the tire pressure mon itor ing indi­
cator must be stored in the MMI
Qpage263 .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 210 Ch ang ing a whee l: Removing the wheel cove r
Removing
.. Insert the hook (provided with the veh icle
tool kit) in the hole in the wheel hub cover.
What do I do now? 267
• Pull off th e decorative wheel cover
Qfig. 210.
Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fig. 211 C hanging a whee l: removing the wheel bolt
caps
Removing
• Push the plastic clip (provided with the vehi­
cle too l kit) over the wheel bo lt cap until the
inner retainers on the clip align w ith the
edge of the cover.
.. Remove the cap with the
plastic clip (veh icle
tool kit)
Qfig . 211 .
Refitting
• Place the caps over the whee l bolts and
push them back on.
The caps are to protect and keep the wheel
bo lts clean .

268 What do I do now ?
loosening and tightening the wheel
bolts
The wheel bolts must be loosened before rais­
ing the vehicle.
Fig. 212 Changing a wheel: loosening the whee l bo lts
loosening
.. Slide the
w heel wr ench onto the wheel bolt
as far as it will go .
.. Take tight hold of the
end of the wrench
handle and turn the wheel bolts co unte r­
clock w ise about one single turn in the direc­
t ion of arrow
c:> fig. 212 .
Tighten ing
.. Slide the wheel wrench onto the wheel bolt
as far as it will go.
.. Take tight hold of the
end of the wrench
handle and turn each wheel bolt
clock wise
until it is seated.
A WARNING
- Do not use force or hurry when changing
a whee l - you can cause the vehicle to slip
off the jack a nd cause serious persona l
injuries.
- Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. - You risk an injury.
@ Tips
- Never use the hexagonal socket in the
handle of the screwdriver to loosen o r
tighten the wheel bo lts.
- If a wheel bolt is very tight, you may fi nd
i t easier to loosen by ca refully p ushi ng
down on the end of the wheel bolt
wrench with
one foot only . As you do so, hold on to the car to keep your balance
and take care not to slip.
Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed.
Fig. 213 Sill panels: markings
Fig. 2 14 Sill: pos ition ing t he ve hicle jack
.. Activate the vehicle jack mode* in the MMI:
!CARI function button> (Car) * syst ems con­
trol button>
Serv icing & ch eck s> Air su sp .:
ja ck mode > On .
.,. Engage the parki ng brake to prevent your
veh icle from rolling unintentionally .
.,. Move the
sele cto r lever to p osition P .
.. Find the mark ing (imprint) on the sill tha t is
nearest the whee l that will be changed
c:>fig. 213. Be hind the marking, there is a
lifting point on the sill for the vehicle jack.
.. Ve hicles with a si ll: remove the cover from
the sill before lift ing the veh icle w ith a vehi­
cle jack c:>
page 269 .
.,. Turn the ve hicl e ja ck located under the lift­
ing point on the sill to ra ise the jack until its
arm @c:>
fig. 214 is located under the des­
ignated plastic moun t c:>
£ c:> (D .
.. Align the jack so that its arm @c:>
fig. 214
engages in the designated lifting point in
the door sill and the movable base @ lies
IJJ>

2 70 What do I do now ?
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 216 Changing a whee l: u sing the screwdriver han­
dle (w ith th e blade removed} to turn the bolts
Fig. 2 17 Changing a w hee l: a lignm en t pi n ins ide t he
top hole
Afte r you have loosened a ll wheel bolts and
r a ised the veh icle off the ground, remove a nd
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal soc ket in th e screwdriv­
er handl e
to complete ly remove the top­
most wheel bo lt and set it as ide on a
clean
s ur face qfig. 216 .
.. Screw the threaded end o f the alignment
pin
from the tool k it hand -tight into the
empty bolt hole
q fig. 217.
.. Then remove the other wheel bo lts as de­
scribed above .
.. Take off the wheel leav ing the alignment pin
in the bolt hole
c:> (D .
Putting on the spare whe el
.. Lift the spare wheel and ca refully slide it
over the a lignment pin to guide it in place
c:> Q).
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all whee l
bolts
slightly.
.. Remove the a lignment pi n and insert and
tighten the remaining wheel bolt slightly
like the rest .
.. Tu rn the jack hand le counter-clockwise to
lower the veh icle until the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts f irm ly
q page 268 . Tighten
them
crosswise, from one bolt to the (ap ­
proximately) opposite one, to keep the
wheel centered.
(D Note
When remov ing or installing the whee l,
the rim cou ld hit the b rake roto r and dam­
age the roto r. Work carefu lly and have a
second person help you .
(D Tips
Never use the hexagonal socket in the han­
d le of the screwdriver to loosen or tighten
the wheel bolts.
- Pull the reversible blade from the screw ­
dr iver before you use the hexagonal
socket in the hand le to turn the w heel
bolts .
- When mount ing tires w ith
unidirectional
tread design
make sure the tread pat­
t er n is po inted t he righ t way
~page 271.
-The wheel bolts shou ld be clean and easy
t o t urn . Check for dirt an d co rrosion on
the mat ing surfaces of both the w heel
an d t he hub . Remove all d irt from these
s urfa ce s be for e remou nting the whee l.

Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in
the right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire w ith a tread pattern
in tended for use in a specific direction, please
note the following:
- The direction of rotation is marked by an ar­
row on the side of the tire.
- If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the tire will not be able to
achieve its optimum performance character­
istic s with rega rd to aquaplaning, noise and
wear.
- We recommend that you pay particular at­
tention to this fact during wet weather and
that you adjust your speed to match road
conditions.
- Replace the flat tire with a new one and
have it installed on your veh icle as soon as
possib le to restore the handling advantages
of a unid irectiona l tire .
Notes on wheel changing
Please read the information c:> page 254, New
tires and replacing tires and wheels
if you are
going to use a spare t ire which is different
from the tires on your veh icle.
After you change a tire :
-Check the tire pressure on the spare imme­
diately after installation .
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm).
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque. What do I do now? 271
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then , drive with extra care and at re­
duced speeds.
A WARNING
-
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were factory installed, then be
sure to read the information<=>
page 254,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
pa rtment and are not loose in the pas­
senger compartment .
- In an accident or sudden maneuver they
could fly forward, in juring anyone in the
veh icle.
- Always store damaged wheel, jack and
too ls securely in the luggage compa rt­
ment. Otherwise , in an accident or su d­
den maneuver they could fly forward,
causing injury to passengers in the vehi­
cle.
•
•

300 Index
Starting from rest . . . . . . . . . . . . . . . . . . . . 80
Starting off with a tra iler ... ... .. .. .. . . 80
Starting the engine .......... .. .. .. .. 76
Steer ing
Electrically adjustable steering whee l .. 75
Manually adjustable steering whee l .. .. 75
also refer to Electro -mechanical power
assist . ...... ................... . 201
Steer ing whee l
Easy entry feature ......... ... .... .. 76
Indicator light . . . . . . . . . . . . . . . . . . . . . 18
Steering whee l heating ..... ... .. ... . 74
Steering wheel column
Adj usting e lectr ically ...... .. .. .. .. . . 75
Adjusting manually ........ ... .. .. .. 75
Steer ing wheel w ith tiptronic ... .. .. .. . 113
Steps for determining correct load limit . 252
Stopping the engine . . . . . . . . . . . . . . . . . . 77
Storage . . . . . . . . . . . . . . . . . . . . . . . . 60, 64
S tronic transmission Launch Control Program ............ 114
S tron ic (automatic transmission) . .... . 109
Sunroof . .. ................... .... .. 42
Sun shade ... ................ ..... .. 48
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Symbols
refer to Warning/indicator lights ...... 12
T
Tachometer . . . . . . . . . . . . . . . . . . . . . 12, 24
Tail lights
C leaning ................ .... ..... 214
TOI clean diesel
refer to Ad Blue .. ...... .... ... .. .. . 223
Technical data .............. ... .. .. . 282
Technical modifications ..... .. .. .... . 288
Temperature d isplay ...... .. .... .. .. .. 24
Tether anchors ..................... 192
Tether strap . ... ......... ... .. .. ... 192
Textiles Cleaning . .. ............. .. .. .. ... 216
The first 1,000 miles (1,500 km) and after-
wards ..... .. ................ ..... . 204
Three-zone climate control .. .. .. .. .. . . 70
Tie-downs . . . . . . . . . . . . . . . . . . . . . 66, 137 T
ips for the environment
Saving fuel . ..... ................ .. 63
t iptron ic (automatic transmission) 109, 113
Tire pressure .... ................... 249
T ire pressure monitoring system ....... 261
Loss of air pressure ................ 262
Malfunction ..... ................ . 262
Resetting tire pressures ......... .... 263
T ires ....... .. .. .. ............... .. 243
Service life .... .. ............. .... 253
Speed rating letter code ............ 255
Tire manufacturing date ............ 255
Tire specifications ............... .. 255
Tread depth ...................... 253
Uniform tire quality grading ..... .... 257
Winter tires ..... ... ........... ... 258
Tires and vehicle load limits ........ ... 251
T ires and wheels
Checking tire press ure ........ .. .. .. 249
Cold tire inflation pressure ....... ... 247
Dimensions . ..... ................ . 254
General notes .... ................ . 243
G lossary of tire and loading terminolo-
gy ....... .. .. .. .. ............... 244
Low aspect ratio tires ............. .. 260
New tires and wheels ........ ... .. .. 254
Replac ing ... .. .. ....... ...... .. .. 255
Snow chains ..... ... ........... ... 259
T ires and veh icle load limits ..... .... 251
Wheel bolts .................. .... 260
Winter tires ...... ................ 258
Tire service life .. .. ..... ..... ... .. .. 253
Too ls ..... ... .. .. ................ . 264
T orn or frayed safety belts ............ 143
Towing Tow truck procedures ........ ... .. .. 278
TPMS Tire pressure monitoring system . .. .. 262
T rai le r towing . .. .. ............... .. 209
Operating instructions .............. 209
Parking system ... ................ . 127
Technical requirements . . . . . . . . 209,210
Trai ler towing tips ................. 211
T rain (transport ing you r vehicle) . .. .. .. 280
Transmission .. .. .. ....... ...... .... 109
Transmission malfunction (indicator
light) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114