lights AUDI A7 2016 User Guide

Instruments and indicator lights
Drive to an authorized Aud i dea ler or authorized
Audi Service Faci lity immediately to have the
malfunct ion corrected .
II Air suspen sion : Vehicle too low Ground
clearance reduced
The gro und clea rance is very low due to a system
malfunct io n. Wait unt il t he air suspension sys­
tem has res tored norma l ground clearance. Oth­
erwise, conditions such as an uneven road sur ­
face can lead to vehicle damage .
~/ !f Safety systems
The JI (USA models)/ E,I (Canada mode ls) indi­
cator light monitors the safety systems (e.g. air­
bags, pretensioners) and illuminates for a few
seconds each time you switch the ignition on .
If the
r.l (USA models)/ E,I (Canada models) in­
d icator light does not go out, or if it illum inates
while you are driving, or if it starts to blink, the n
there is a malfunction somewhe re in the system .
If the light does not ill uminate w hen you switch
the ign ition on , this also means the re is a mal­
function .
.&, WARNING
-
If you have a mal func tion in the safety sys­
t ems, contact your authorized A udi dealer im ­
mediately . Othe rwise the safety systems may
not work properly in an acci dent .
& Brake booster
U Brake servo : limited functional ity . You can
con tinue d riv ing. Con tact workshop
There is a malfunction in the brake booster. The
brake booster is availab le, but its effectiveness is
red uced. Braking behavior may be different from
how it normally functions and the brake peda l
may vibra te.
Drive to an a uthorized Audi dea ler or a uthorized
Aud i Service Fac ility immediately to have the
malfunct ion corrected.
18
r;. I[/; Electronic Stabilization Control (ESC)
If the ffl ind icator light blinks while driving , the
E S P or ASR (ant i-slip reg ulation) is act ively reg u­
l ati ng .
If the
ffl ind icator light turns on, the system has
switched the ESC
off . In this case, you can switch
t h e ign it io n
off and t hen on to sw itch the ESC on
again. The indica tor ligh t turns
off when the sys­
tem is functioning fu lly.
If the . indicator light tu rns on, ESC was
swi tched
off using the I~ OFF I bu tto n
~page 188 .
Stabilization control (ESC /ABS ) malfunction!
See owner' s manual
If the DJ ind icator light and the ABS indicator
li ght
fn:) (USA models) ;ti] (Canada models)
turn o n and the message appears, the ABS or
e lectronic differe ntia l lock is malfunc tioning. This
also ca uses the ESC to mal function. The br akes
sti ll fu nct ion with their no rma l powe r, b ut ABS is
not active.
D rive to your au thori zed A udi dealer or qualified
workshop immedia tely to have the mal func tion
corrected .
.&, WARNING
If the 1111 (USA models) ;II (Canada mod ­
e ls) b rake system indicator light turns on to­
gether with the ABS and ESC ind icator lights,
the ABS/ESC regulat ing funct ion may have
failed. Functions that stabilize the vehicle are
n o longer availab le. This could cause the vehi ­
cle to swerve and increase the risk of slidi ng.
D rive ca refully to the nea rest authorized Audi
dealer o r othe r qualified workshop and have
the ma lf unc tion correc ted.
(D Tips
Fo r additional informat ion on ESC and ABS,
r efer to
~ pag e 188.

M N <( (.J
'SI: ,...., \!) 1.1'1
N \!) ,....,
ABS/(@)) Anti-lock braking system (ABS )
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
The warning/indicator light
,n:) (USA models) /
ill (Canada models) will come on for a few sec­
onds when the ignition is switched on. The light
will go out after an automatic check sequence is
completed.
There is a malfunction in the ABS when:
-The warning/indicator light does not illuminate
when you switch the ign it ion on.
- The warning/indicator light does not go out af­
ter a few seconds.
- The warning/indicator light illuminates while driving .
The ESC indicator light also illuminates if there is
a ma lfunction in the ABS . The message
Stabiliza­
tion control (ESC/ABS): Fault! See owner's man­
ual
also appears in the instrument cluster display
and a warning tone sounds.
The brake system will still respond even with­
out the assistance of the ABS system. See your
authorized Audi dealer as soon as possible to re­
store full braking performance.
For more infor­
mat ion regarding the ABS ¢page 188.
Malfunction in the brake system
If the brake warning light¢ page 14 and the ABS
warn ing illuminate together there may be a mal­
function in the ABS, and there may also be a mal­
function in the brake system itself¢,& .
The ABS
will not work and you will notice a change in
braking response and performance.
In the event of a malfunct ion in the brake sys­
tem
the warning/indicator light 1111 (USA mod­
els)/. (Canada models) in the instrument clus­
ter flashes ¢ page 14 .
Malfunction in the electronic differential
lock (EDL)
The ED L works together with the ABS . The ABS
warn ing light will come on if there is a malfunc­
tion in the EDL system
c::> page 188 . See your au­
thorized Audi dealer as soon as possible.
Instruments and indicator lights
A WARNING
-If the ,n:) (USA mode ls)/ ill (Canada mod­
els) warn ing light does not go out, or if it
comes on while dr iv ing, the ABS system is
not working prope rly . The vehicle can then
be stopped only with the standard brakes
(without ABS) . You will not have the protec­
tion ABS provides. Contact your Audi dealer
as soon as possible .
- USA models: If the
1111 warning light, the
G1 warning light and the ,n:) warning light
come on together, the rear wheels could
lock up first under hard braking . Rear wheel
lock-up can cause loss of vehicle control and
an accident. Have your vehicle repaired im­
mediately by your author ized Audi dealer or
a qualified workshop . Dr ive slowly and avoid
sudden, hard brake applications .
- Canada models: If the brake warning light
• • the
DJ warning light and the ABS warn­
ing light
ill come on together, the rear
wheels could lock up first under hard brak­
ing. Rear wheel lock-up can cause loss o f ve ­
hicle control and an accident . Have your ve­
hicle repaired immediately by your author­
ized Audi dealer or a qualified workshop.
Drive s low ly and avoid sudden, hard brake
applications.
{0) Worn brake pads
EiJ Brake pads!
-
If the warning light i lluminates, immed iate ly
contact your authorized Audi dealer or qualified
workshop to have all brake pads inspected. On
USA models the warning light
EiJ comes on to­
gether w ith the warning light
1111 . Both sets of
brake pads on an axle must always be replaced at
the same time .
A WARNING
Driving with bad b rakes can cause a collision
and serious personal injury .
-
19

Instruments and indicator lights
-If the warning light EiJ and the warning
light
11111 ) with the message Brake pads!
comes on in the instrument cluster display,
immediately contact your authorized Audi
dealer or qualified workshop to have all
brake pads checked or replaced if necessary.
EPC Electronic power control
Applies to vehicles: w ith gaso line engine
This warning/indicator ligh t monitors the elec­
tronic power control .
The (m warning/indicator light (Electronic Powe r
Control) illuminates when you switch the ignition
on as a function check.
{!) Tips
If this warning/indicator light illuminates
while you are driving, then there is a malfunc­
tion in the engine electronics. Have the mal­
function corrected as soon as possible by your
authorized Audi dealer or qualified repair fa­
cility.
W Glow plug system
App lies to vehicles: with diesel engine
The control light illuminates when the glow plug
system is active.
If the El indicator light illuminates, the glow
plug system is active . You should start the engine
immediate ly after the indicator light switches off.
The indicator light only illuminates for approxi­
mately 1 second if the engine is warm or if the
outside temperature is above 46 QF (8 QC).
@ Tips
-If the glow plug indicator light illuminates
while driving, there is an engine control
malfunction. The engine should be checked
immediately.
- If the indicator light does not illuminate at
all when switching the ignition on, there may be a malfunction in the glow plug sys­
tem. The engine should be checked.
l) - : USA mo dels onl y
20
o Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is part of
the On-Board Diagnostic (OBD II) system. The symbol
('4 lights up when the ignition is switch­
ed on and will turn off after the engine has start­
ed and has settled at a constant idle speed . This
indicates that the MIL is working properly.
The warning light illuminates when there is a
malfunction in the engine electronic system.
Contact your authorized Audi dealer and have the
malfunction corrected.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢ page 212.
For more information ¢ page 28.
~ Diesel particulate filter
Applies to vehicles: with diese l engine and diesel particulate
filter
II Particulate filter: System fault See owner's
manual
The diesel particulate fil ter requires regenera­
tion . To support the filter's self -cleaning func­
tion:
Drive for approximately 15 minutes with these­
lector lever in the S position at a minimum speed
of 37 mph (60 km/h) and an engine speed of ap ­
proximately 2,000 RPM . The temperature in­
crease that will result from this can burn off the
soot in the filter . T he symbol will switch off when
the cleaning is successful.
If the indicator light does
not turn off, drive im­
mediate ly to an authorized Audi dealer or author­
ized Audi Serv ice Facility to have the malfunction
corrected.
_&, WARNING
Always adapt your speed to the current
weather, road and traffic conditions . You
should never disobey traffic laws in order to
follow driving recommendations.

M N <( (.J
'SI: ,...., \!) ..,.,
N \!) ,....,
@ Tips
For additional information on the diesel par­
ticulate fi lter, refer to ¢
page 198.
!?) Engine speed limitation
App lies to vehicles: with e ngin e speed limitat ion
Ill Engine speed maximum XXXX RPM
The engine speed is automatically limited to the
speed displayed in the instrument cluster. This
protects the eng ine from overheating.
The engine speed limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped­
al.
If the engine speed limitation was activated by
an engine control malfunction, the
Im indicator
light also turns on. Make sure that the speed
does not go above the speed d isplayed. Drive to
an authorized Audi dealer or authorized Audi
Service Facility immediately to have the malfunc­
tion corrected .
.., Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your author­
ized Audi dealer and have the oil sensor inspect ­
ed. Until you have th is done, check the oil level
each time you refuel just to be on the safe side
¢page 222.
f Engine warm-up request
n Please warm up engine
Fuel has entered the engine oil, either from low
outside temperatures or frequent short d rives.
Drive until the engine is warm so that the fuel in
the eng ine oi l wi ll evaporate. Avoid high eng ine
speeds, full accelerating and heavy engine loads
when doing this .
Bil Fuel tank system
Ii] Please refuel
Instruments and indicator lights
If the indicator light turns on for the first time
and the message appears, there are about 2.6
gallons (10 liters) of fue l left in the tank.
Ii] Fuel tank system malfunction! Contact deal­
er
T he re is a malfunction in the fuel tank system.
Drive to an authorized Audi dealer or authorized
Audi Serv ice Facility immediately to have the
malfunction corrected .
{!) Tips
More information on refueling is available on
page
¢ page 212.
• Washer fluid level
m Please refill washer fluid
Fill the washer fluid for the windshield washer
system and the headlight washer system* when
the ignition is switched off ¢
page 231.
• Windshield wipers
m Windshield wiper defective
There is a malfunction with the windsh ield wip­
ers .
Drive to an authorized Audi dealer or authorized
Audi Serv ice Facility immediately to have the
malfunction corrected .
~/0$ Defective light bulb warn ing
If the J:!1 ind icator light turns on, a light has
failed. The message ind icates the location of the
light. If the
[tD indicator light a lso turns on, then
a rear fog light has failed. The position of the in­
dicator light corresponds with the location on the
vehicle.
Drive to an authorized Audi dealer or authorized
A udi Service Facility immed iately to have the
malfunction corrected.
Vehicle lights: Malfunction
There is a malfunction in the headlights or the
light switch.
21

Instruments and indicator lights
Drive to an authorized Aud i dea ler or authorized
Audi Service Faci lity immediately to have the
malfunct ion corrected .
~(D Headlight range control
El Headlight range co ntrol: defe cti ve !
If the symbo l illuminates, the headlight range
control is no longer working properly. Have the
system checked and repaired at your A udi dealer .
1aO Adaptive Light
Applies to veh icles: with Adapt ive Light
mi Aud i adapti ve light: system fault
If the indicator lig ht t urns on and this message
appears, there is a malfunction in the adaptive
light system . The headlights still f unction.
Go to an a uthorized dea le rship to have the head ­
lights or the control unit for the Adaptive Light
repaired.
~ o Light/rain sensor
El Automatic headlights / automat ic wipe rs:
System fault
The light/rain sensor is malfunctioning.
F or safety reasons , the low beams are turned on
permanen tly with the switch in
AUTO. However,
you can continue to turn the lights on and off us­
ing the light switch . You can still control a ll func­
tions that are independent of the rain sensor
t hrough the windshield wiper lever.
D rive to an a uthorized Audi dea ler or a uthorized
Aud i Service Faci lity immediately to have the
malfunct ion corrected.
!-- : Sport differential
Applies to veh icles: w ith sport different ia l
II) Sport di fferential : system fault
There is a malfunction with the sport differentia l.
Drive to your aut ho rized Aud i dea le r i mmedia tely
to have the ma lfunction co rrec ted .
II) Sport differential: overheating
22
The transm ission temperat ure has increased s ig ­
nificantly d ue to the sporty driving manner. Drive
i n a less sporty manner unt il the temperature re­
turns to the normal range and the indicator light
switches of.
A WARNING
-
Contact your author ized Audi dealer or a
qualified workshop if the spo rt differential is
fa ulty o r malfunctioning . The repa ir must be
performed by trained pe rsonnel using the cor­
rect o il in order to ens ure s afety.
¢ ¢Turn signals
The indicator light blinks when you use either
turn signal.
Wheneve r you use the left B or the right B
turn s ignal, the indicator light blinks . When you
use the eme rgency flashers, bot h indicator lights
flash.
If one of the turn signa l light bulbs burn out, the
turn s ignal will bli nk twice as fast as normal.
Carefully dr ive to your author ized Audi dealer im­
med iate ly to have the malfunction cor rected. The
i ndica tor l igh t does not ind icate a ma lf u nction if
a turn signal on the tra iler or on the vehicle fails
i n tra iler towing mode.
(D Tips
Fo r more informa tion on the turn s ign als , re­
fer to<=>
page 44.
CRUISE 1• 0 Cruise control
The warning/indicator lig ht (ij;(l)~14 (USA mode ls)/
l'I (Canada mode ls) illuminates when the cruise
control is activated <=>
page 83.

M N <( I.J "". rl I.O
"' N I.O rl
Driver information
system
Overview
Fig. 4 Driver information system in th e instr ument cluster
Fig. 5 Display: example of the informat ion line
The driver information system conta ins informa­
tion @ that is disp layed on tabs@¢
fig. 4 . The
following content is possible depending on vehi­
cle equipment:
@
®
Tab C o ntent
1 Veh icle functions:
On-board computer ¢ page 24
Efficiency program* ¢ page 25
Digital speedometer
Cruise control *¢
page 83
Adapt ive cruise control and braking
guard*
¢ page85
Audi active lane assist*¢ page 94
Display darkened Ins
trument s and indi cator ligh ts
@
®
Tab Content
2 Ind icator lights and messages
Warning when a door, the hood or the rear lid is not closed
Service interval display¢
page 26
Speed warning system ¢ page 82
3 Night vision assistant* ¢page 104
4 Audio/video
s Telephone*
6 Navigat ion*
T he second and third tabs are only visible if at
least one indicator light or message is shown or if
that system is switched on.
The status line© is located in the bottom part of
the display ¢
fig. 4. It displays the exterior tem­
perature, time, selector lever position, tripod ­
ometer and odometer .
For some vehicle functions, you can access the
trip information from the temporary memory
¢ page 25 in the line(!)¢ fig. 5.
_& WARNING
-
-Never rely exclusively on the outside tem­
perature display to determine if a road sur­
face is icy or not. Keep in mind that road sur­
faces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperatu re above 4 1 °F (+S
0
().
- Always remember, even if the "snowflake"
symbol (ice warning) does not appear in the
d isp lay, black ice cou ld be on the road.
- Always reduce your speed and drive with
specia l care in cold weather cond itions when
the chance of encountering icy road surfaces
i n creases.
(0 Tips
- If the vehicle is stationary, or if you are driv­
ing at a very low speed, the temperature
shown in the display might be slight ly high­
er than the actual outside temperature. This
is caused by the heat being radi ated from
the engine . .,..
23

Instruments and indicator Lights
- You can se lect the un its used for tempera ­
ture, speed an d other meas urements in the
M MI.
- For informat ion on the a udio/video and nav­
i gat io n* functions, refe r to t he se parate
M MI owner's manual.
Operation
The driver information system is operated using
th e buttons on the multifunction steering wheel .
Fig . 6 Mult ifu nctio n stee ring w hee l: operat ing t he drive r
i nforma tio n syste m
Fig. 7 In stru ment cluster: call in g up t he ve hicle fu nctio ns
men u
Operat ing
.,. Switc h the ignition on .
.. To sw itch between the tabs, p ress the rocker
switc h @ to the left or right ¢
fig. 6 .
.,. To access addi tio nal i nfo rmat io n be low or
above , turn the thum bwhee l@ dow n or u p.
.. To confirm a se lection, press the thumbwhee l
@.
.. To ope n the s ubme nu for an active ta b, press
the button ~@-
....
-N 9 (!:I .,. OJ
.,. To select a function programmed to a steering
whee l button*, press the button@.
24
Opening the Vehicle functions
.,. Sele ct the first t ab with the ro cker swi tch@ .
.. Press th e ~ button @. T he
Vehicle functions
menu is disp laye d ¢ fig . 7 .
.,. To se lect a menu item, tu rn and press the
thumbwhee l@ .
Resetting values to zero
.,. In t he Vehicle fun ctions me nu, sele ct On-bo ard
computer
o r Efficiency program.
.,. Yo u can now select between the long-term
memory and short-term memory .
.,. To reset the values in a memory, press and hold
the t humbwheel @for one second .
Assigning a function to a programmable
steering wheel button*
.,. Select the I CAR I funct ion button > (Car )* Sys­
tems
control b utt on > Vehicle settings > Steer­
ing wheel button programming .
The last function selected displays when you
switch the ig nition on .
On-board computer
Fig. 8 In stru men t cluster: fuel cons ump tio n
You can ca ll up the followi ng i nfo rmation in the
on-board comp uter :
- Da te
- Dr iv ing t ime (h) fro m the short-te rm memory
- Av erage cons umption in MPG ( l/100 km) from
t he sho rt-term memo ry
- Average spee d in mph (km/h) fro m the short ­
term m emory
- Distance drive n in miles (km) from the shor t­
term memory
- Cur rent fue l consumption in MPG ( l/100 km)

Instruments and indicato r Lights
Economy tips
In certain situat ions, economy tips appear auto­
matica lly for a short time in the efficiency pro­
gram ~
fig. 10. If yo u follow these economy tips,
you can reduce your vehicle's fuel consumption.
To turn an economy tip off immediately after it
appears, press any button on the multifunction
steering whee l.
(D Tips
-If you e rase the data in the efficiency pro­
gram, the values in the on-board computer
will a lso be reset.
- Once you have turned an economy tip off, it
will on ly appear again after you turn the ig­
nition on again.
- The economy tips are not displayed in every
instance, but rather in intervals over a peri­
od of t ime .
Odometer
Fig . 11 Instrum ent cluste r: o dom eter an d res et butto n
The display of distance driven is shown in m iles
"mi" or kilometers "km". The units of measure ­
ment (kilometers/miles) can be changed in the
Infotainment system.
Upper odometer
The trip odometer shows the distance driven
since it was last reset . It can be used to measure
short distances. The last digit shows distances of
100 meters or 1/10 of a mile .
The trip odometer can be reset to zero by press­
ing the reset button~-
26
Lower odometer
The lower odometer shows the total number o f
kilometers or miles that the vehicle has driven.
Malfunction indicator
If there is a malfunction in the instrument clus­
ter ,
DEF will appear in the tr ip odometer display .
Have the malfunction corrected as soon as poss i­
ble.
Time/date display
Fig. 12 Ins trumen t cl uster : T im e and dat e
The date, time of day and time and date format
can be set in the Infotainment system. Refer to
the Infotainment system operating manual fo r
instructions.
When you open the dr iver's door, the date and
time appear in the instrument cluster display for
30 seconds .
Service interval display
The service interval display detects when your ve­
hicle is due for service .
Fig. 13 Instrume nt cluster d ispl ay: service interv al displ ay
(example)
The service interval display works in two stages: ..,.

M N <( I.J "". rl I.O
"' N I.O rl
-Inspection or oil change reminder: After a cer­
tain distance driven, a message appears in the
instrument cluster display each time the igni­
tion is switched on or off
c> fig. 13. The remain­
ing distance or time is displayed briefly .
-Inspection or oil change due : If your vehicle is
due for an inspection or oil change or both, a
message appears br iefly in the instrument clus­
ter display when switching the ignition on or
off:
Inspection due! or Oil change due! or Oil
change and inspection due! .
Checking service intervals
You can check the remaining distance or time un­
til the next oil change or next inspection n the
Car menu. To do th is, select: the ICAR !function
button
> (Car) * Systems control button > Service
& control
> Servi ce intervals .
Resetting the indicator
Your authorized Audi dealer or authorized Audi
Service Facility will reset the service interval dis­
play after performing service .
If you have changed the oil yourself, you must re­
set the oil change interval.
To reset the indicator, select: the ICARI fu nct ion
button
> (Car)* System control button > Service
& control > Service intervals. Turn the control
knob downward to
Reset oil change interval and
press the control knob.
(D Note
- Only reset the oil change indicator if the o il
was changed.
- Fo llowing the service intervals is critical to
maintain ing the service life and value of
your vehicle, especially the engine. Even if
the mileage on the vehicle is low, do not ex­
ceed the time for the next service.
- Calculating the time to the next oil change
i s interrupted when the vehicle battery is
disconnected. If the vehicle is not driven for
a long period of time, check the mainte­
nance schedule so that you can follow the
maintenance interva ls.
Instruments and indicator lights
Head-up display
Applies to vehicles: wit h Head-up disp lay
Fig. 14 Examp le : Indicato rs i n th e Head -up dis play
Fig . 15 Instrument panel: head-up display knob
The Head-up display projects certain warnings or
selected information from the assistance sys ­
tems* or navigation* on the windsh ield . T he dis­
play appears w ith in the dr iver's field of vision.
Switching on/off
... To switch the head-up d isplay on or off, press
the knob~
c> fig. 15.
Adjusting the height
The height of the display can be adjusted to the
individual driver.
... Make sur e you are seated correctly
r=!)page 127 .
... Tur n the knob~ to adjust the disp lay .
Settings in the Infotainment system
... Sele ct: the I CARI function button > (Car)* Sys­
tem
control button > Driver assistance > Head­
up display > Head-up display contents or Dis-
play brightness. ..,
27

Instruments and indicato r Lights
Display content
In the Infotainment system, yo u can specify
which information should be displayed : For ex­
ample , this can include navigation information*,
Adapt ive cruise control * or night vision assist *.
The display of certain information and some of
the red indicator lights cannot be hidden in the
Infotainment system.
Display brightness
You can adjust the display brightness in the Info­
tainment system. The display brightness decreas­
es automatically as th e amount of light decreas­
es. The basic level of brightness is adjusted with
the instrument illum ination ¢
page 47.
(D Note
To prevent scratches on the gla ss covering the
Head-up display, do not place any objects in
the projection opening.
@ Tips
-Sunglasses with polar izat ion filters and un­
favorable lighting conditions can affect the
display.
- An optimum display depends on the seat
position and the height adjustment of the
head-up display.
- A specia l windshield is needed for the head­
up display function.
- For informat ion on cleaning, refer to
Q ta­
ble on page
207.
On Board Diagnostic
System (OBD}
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢..ifl in the
instrument cluster is part of the On-Board Diag­
nostic (OBD II) system.
The warning/indicator light illuminates when the
ignit ion is switched on and goes out after the en­
gine starts and the idle has stabilized. This indi­
cates that the MIL is working properly.
If the light does not go out after the engine is
started, or illuminates while you are dr iving, a
28
malfunction may exist in the engine system. If
the light illum inates , the catalytic converter
could be damaged.
Continue driving
with reduced power (avoiding
sustained high speeds and/or rapid accelerations)
and have the condition corrected. Contact your
authorized Aud i dea ler.
If the ligh t illuminates, the electronic speed lim­
iter may also be ma lfunctioning . For more infor­
mation ¢
page 29, Electronic speed limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
Q page 212.
On-Board Diagnostics
Fig. 16 Locat io n of Data Link Co nnector (DLC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code . In case o f a malfunct ion, the com­
ponent will be identified and the fault stored as a
code in the control module memory .
The MIL light may also ill uminate if there is a
leak in the on-board f uel vapor recove ry system.
If the light illuminates after a refuelling, stop the
vehicle and make sure the fuel filler cap is prop­
erly closed
c:> page 212.
In order to make an accurate diagnosis, the stor ­
ed data can only be displayed using special diag­
nostic equipment (generic scan tool for 080).
In order to connect the specia l diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release ¢
fig. 16. ..,.