clock AUDI A7 2017 Owner´s Manual

co
co
.... N
" N .... 0
00
<.,;) 'SI"
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel.
Fig. 207 Changing a wheel: using the screwdriver hahd le
(with the blade removed} to turn the bolts
F ig. 208 Changing a wheel: alignment pin ins ide the top
hole
After you have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and re­
p lace the whee l as follows:
Removing th e wheel
" Use the hexagon al so cket in the screwdri ver
handle to completely remove the topmost
wheel bolt and set it aside on a
clean surface
¢fig. 207.
.. Screw the threaded end of the alignment pi n
from the tool kit hand-tight into the empty bolt
hole
¢ fig. 2oa1>.
" Then remove the other wheel bolts as described
above .
" Take
off the wheel leaving the a lignment pin in
the bolt ho le
¢ 0 .
l) Applies to vehicles with ceram ic brake rotors•: Use a sec­
ond alignme nt pin• (stored in t he spa re wheel well mold ­
ing} for the lower hole , fo llow ing the descript ion for the
first alignment pin.
Em ergen cy a ssis tanc e
Putting on th e spar e wheel
" Lift the spare whee l and caref ully slide it over
the alignment pin to guide it in place¢(!).
.. Use the hexagona l socket in the screwdriver
handle to screw in and tighten all wheel bolts
slightly .
"Remove the alignment pin and insert and tight­
en the remaining wheel bo lt slightly like the
rest .
.. Turn the jack hand le counter-clockw ise to lower
the vehicle unt il the ja ck is fully released.
" Use the wheel bo lt wrench to t ighten a ll wheel
bolts firmly¢
page 245. Tighten them cross­
wise,
from one bo lt to the (approx imately) op­
posite one, to keep the wheel centered.
(D Note
When removing or installing the wheel, the
rim could hit the brake rotor/ceramic brake
rotor* and damage the rotor . Work carefully
and have a second person he lp you.
(D Tips
Never use the hexagonal socket in the hand le
of the screwdriver to loosen or tighten the
whee l bolts.
- Pull the reversible blade from the screwdr iv ­
er before you use the hexagona l socket in
the handle to turn the wheel bolts.
- When mounting tires with unidirectional
t read de sign make sure the tread pattern is
pointed the right way
¢ page 248.
- The wheel bolts sho uld be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
247

co
co
.... N
" N .... 0
00
\.J - There are some restrictions on the use of the
spare tire. The spare tire has been designed spe ­
cifically for your type of vehicle. Do not replace it
with the spare tire from another type of vehicle.
Spac e-sav ing spar e tir e*
The tire pressure must be 61 PSI (4.2 bar).
Remo ving the spar e tire
~ Fold the cargo floor up to the rear bench seat .
~ Turn the handwheel counter-clockw ise and re-
move it.
~ Remove the spare tire.
Snow cha ins
Using snow chains on the spare tire is not perm it ­
ted due to technical reasons .
If you have to drive with snow chains and a front
tire fails, mount the spare tire in place of a rear
tire . Install the snow chains on the rear tire that
you removed, and install that in place of the
front tire that failed.
A WARNING
-
- After installing a spare t ire, the tire pres­
s u re must be checked as quickly as poss ible.
- Do not drive faster than 50 mph (80 km/h)
with a spare tire. Dr iv ing faster than that in ­
creases the risk of an acc ident.
- Avoid full-throttle accelerat ion, heavy b rak­
ing, and fast cornering, beca use this in­
creases the risk of an accident.
- Never drive us ing more than one spare t ire,
because th is increases the risk of an acci­
dent.
- Norma l t ires o r winter tires must not be
mounted on the spare tire rim .
- Only use the co llaps ible spa re ti re in emer­
gencies and dr ive very carefu lly, especially if
it is more than 6 years o ld .
Em ergenc y ass is tanc e
249