lock AUDI A8 1996 D2 / 1.G 01V Transmission Select Lever Mechanism Owner's Manual

37-38

Shift lock solenoid, removing and installing

Removing

- Remove shift mechanism page 37
-6 .

- Remove stop buffer from cable lever.

- Shift selector lever into Tiptronic position and
then remove frame.

- Shift selector lever into position "2".

- Disengage lever for locking cable by lifting it out
of its bearing and remove from shift mechanism
housing.

- Press out pin for locking latch using a drift.

- Remove shift lock solenoid together with locking
latch upward.
Pa
ge 43 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-39

Installing

- Shift selector lever into position "2".

- Shift lock solenoid together with locking latch
must be slid into the shift mechanism housing
from the top.

- Carefully drive in pin for locking latch.

- Using a screwdriver, mechanically check for
engagement of the locking latch in position "P"
and "N" of selector lever.

- Lay cable lever into shift mechanism housing
and engage it noticeably in both bearing areas.

- Check locking function of locking lever. In
selector lever position "P", it must engage in the
catch and lock the shift mechanism.

- Set frame onto shift mechanism housing (ribbing
points upward) and insert buffer stop into cable
lever.

- Install shift mechanism page 37
-6 .
Pa
ge 44 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-42
Disconnect selector lever cable from shift
mechanism housing:

- Press ends of locking clip -B- together and remove.
- Remove securing plate -A- for selector lever cable at shift mechanism
downward.
- Remove selector lever cable from selector lever.

Installing - Pry off selector lever cable from lever/shift rod using 80-200 pry lever
(arrow).
- Remove bracket from transmission.
- Loosen selector lever cable from bracket.
- Pull selector lever cable out of shift mechanism housing without
kinking.
Selector lever and lever/shift rod in position "P" (park lock must
engage).
- Do not bend or kink selector lever cable, lightly grease coupling ring
and ball socket before installing
Pa
ge 47 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-43

- Guide selector lever cable into shift mechanism
housing.

- Connect selector lever cable to selector lever.

Installation position:
Angled end of securing plate points toward the end of the selector lever
cable. - Press ends of locking clip -B- together and secure selector lever cable.
- Install securing plate -A- for selector lever cable to shift mechanism.
- Connect selector lever cable to bracket by hand.
- Bolt bracket to transmission by hand.
- Press selector lever cable onto lever/shift rod.
- Align selector lever cable in bracket.

- Tighten bracket/transmission (arrows 1) and selector lever
cable/bracket (arrow 2) to tightening torque. During this, counterhold at
hex socket (arrow 3).
Pa
ge 48 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-45

Selector lever cable for Tiptronic shift
mechanism, checking and adjusting


Checking

- Shift selector lever into position "P".

- Raise vehicle.

- Remove shielding plate/selector lever cable.

- Pry off selector lever cable from lever/shift rod (arrow).
- Shift selector lever from "P" to "2".
Shift mechanism and selector lever cable must have freedom of
movement during this, if necessary, replace selector lever cable or
service shift mechanism.
- Shift selector lever into position "P".
- Shift lever/shift rod to "P", parking lock must engage, both front wheels
cannot be turned in one direction. It must be possible to push selector lever cable onto lever/shift rod, if
necessary adjust selector lever cable.
Pa
ge 50 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-46

Adjusting

Selector lever cable has been loosened from
lever/shift rod.

- Shift selector lever into position "P".

- Shift lever/shift rod to "P", parking lock must
engage, both front wheels cannot be turned in
one direction.

- Loosen mounting bolts (arrows) of bracket at transmission.
- Press selector lever cable onto lever/shift rod.
- Align selector lever cable in bracket.
- Tighten mounting bolts (arrows) of bracket at transmission to 23 Nm.
- Install shielding plate/selector lever cable
- Check shift mechanism page 37
-2 .
Pa
ge 51 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-47


Locking cable for Tiptronic shift
mechanism, removing and installing

Removing
Repair Manual, Body Interior, Repair Group 68;
storage compartments/covers; front center console, removing and installing
- Shift selector lever into position "2".
- Note radio code (for vehicles equipped with
coded anti-theft radio).
- Disconnect Ground (GND) strap from battery.
- Selector lever handle, removing page 37
-22
- Front center console, removing
Pa
ge 52 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-48


Repair Manual, Body Interior, Repair Group 69;
Airbag; Steering wheel, removing and installing
- Remove steering wheel.
- Switch ignition key to driving position (ignition
on).
- Shift selector lever into position "P".
- Lift up retaining clip of interlock lever -1- and pull
locking cable out of ignition/starter switch.
- Remove cover with guide (selector lever
mechanism) page 37
-5 .
- Unclip locking cable from securing spring at shift
mechanism housing, slightly lift up securing
spring to do so Fig. 1
, page 37
-21
.
- Loosen and remove locking cable from cable tie
-2-.
Pa
ge 53 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-49


Installing
- Route locking cable without kinking.
- Switch ignition key to driving position (ignition
on).
- Insert locking cable into ignition/starter switch.
- Check locking mechanism of interior lever -1-.
- Secure locking cable to airbag sensor using
cable tie -2-.
- Bring ignition/starter switch into locking position
(ignition off).
- Shift selector lever into position "P".
- Clip locking cable into securing spring of shift
mechanism housing Fig. 1
, page 37
-21
.
- Hook locking cable bracket -3- into shift
mechanism and locking coupling ring in lever (for
locking cable).
Pa
ge 54 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-50


Adjusting
- Shift selector lever into position "P".
- Loosen bolt -6-.
- It must be possible to slide bracket -3- in
direction of arrow -5-.
- Adjust steering column downward.
- Connect 3352 A adjustment pin for shift lock 3 -
item 4- between lever (for locking cable) and
locking coupling ring.
- Pull locking cable in direction of arrow -5- and
tighten bolt -6- to 10 Nm.
- Remove adjusting gauge.
- Check ignition key removal lock after every
adjustment of the locking cable page 37
-1 .
Pa
ge 55 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1