display AUDI A8 1996 D2 / 1.G AEB Engine Throttle Valve Control Module And Checking

Display group: 3


Display field: 3
Possible cause
Corrective action
0.0
Open circuit in wiring- Check wiring Page 24
-116
99.0
Short circuit to ground (GND)
Pa
ge 28 of 38 Throttle valve control module, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.2

24-120

Test procedure

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with ignition
switched on; engine not running) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -6- and -0- to input display group number 60, and
press -Q- button to confirm input.
System in Basic Setting 60 1 2 3 4

Indicated on display (1-4 display fields)
Note:
After confirming input of display group 60, adaptation is started. The
Throttle Position (TP)sensor is positioned in the closed throttle, wide
open throttle and limp-home positions. Following this procedure, other
intermediate steps will create a characteristic curve of the relationship
between Throttle Position (TP) sensor -G69- and angle sensor for
throttle drive -G187-. The Motronic ECM stores these values in permanent memory.
Afterward, the throttle valve assumes the starting position.
Pa
ge 35 of 38 Throttle valve control module, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.2

24-121

- Compare display with specified values (display
fields 1-4):

Display fields

1 2 3 4
Display group 60: Basic setting-throttle valve control module
Display
xxx
xxx
Idle
Part throt
Full throt
Decel
Enrich ADP runs
ADP. OK
ADP. ERROR
Indicates Throttle valve
angle Throttle drive
angle Operating
condition Adaptation condition
Range
0-90
--- ---
Specified
value 0-5 Idle ADP. runs

ADP. OK

(ADP. ERROR indicates unsuccessful
adaptation)

If displayed values are NOT OK:
- Check DTC memory ( Page 01
-15
)
Pa
ge 36 of 38 Throttle valve control module, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.2

24-122
If displayed values are OK:

- Allow at least 30 seconds.

- End adaptation as soon as possible after 30
seconds by pressing button.
- Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
input.
Pa
ge 38 of 38 Throttle valve control module, checkin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.2