oil dipstick AUDI A8 1996 D2 / 1.G AHA ATQ Engines Lubrication System Components Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1996, Model line: A8, Model: AUDI A8 1996 D2 / 1.GPages: 34, PDF Size: 0.68 MB
Page 1 of 34

17-1
 
     
Lubrication system 
components, removing and 
installing 
     
WARNING! 
     
Do not re-use any fasteners that are worn or 
deformed in normal use. 
     Some fasteners are designed to be used only 
once, and are unreliable and may fail if used 
again. This includes, but is not limited to, 
nuts, bolts, washers, circlips and cotter pins. 
Always follow the recommendations in this 
manual-replace these fasteners with new 
parts where indicated, and any other time it 
is deemed necessary by inspection. 
     
CAUTION! 
     If large quantities of metal particles or other 
deposits (caused, i.e. by partial seizure of the 
crankshaft or connecting rod bearings) are 
found in engine oil, thoroughly clean oil 
passages and replace oil cooler to prevent 
damage from re-occuring. 
     Do not overfill with oil past the MAX mark on 
the oil dipstick. Damage to the Three Way 
Catalytic Converter (TWC) could result. 
Pa
ge 1 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1 
Page 8 of 34

17-5
 
  
Oil pump, oil pan, oil filter, oil cooler, 
removing and installing
 
1 - 
Bolt for dipstick tube 
25 Nm (18 ft lb)
2 - 
Dipstick tube Replace O-ring
3 - 
Oil pan (upper part) No gasket is installed between engine 
block and oil pan (upper part) Only use silicon sealant D 454 300 A2
4 - 
Bolt M820 Nm (15 ft lb)
5 - 
Bolt M615 Nm (11 ft lb)
6 - 
Bolt M820 Nm (15 ft lb)Bolt is next to coolant drain plug
Pa
ge 8 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1 
Page 14 of 34

17-10
      
Oil pan (upper part) and oil pan (lower 
part), removing and installing
 
     
Special tools and equipment  
     
Drill with plastic brush attachment
     Sealant D 454 300 A2
     Torque wrench 10 Nm - 45 Nm
     
-  Switch ignition off and disconnect battery 
Ground (GND) strap. 
     
CAUTION! 
     
Before disconnecting the battery, determine 
the correct coding for the anti-theft radio. 
     
- Withdraw dipstick.
     
-  Unbolt dipstick tube at right-front of cylinder 
head, pull up and remove. 
    
-  Remove noise insulation panel (arrows).
Pa
ge 14 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1 
Page 27 of 34

17-23
      
Tightening torques  
     
Component  
  
Tightening 
torque  
Oil pan to cylinder block   M6   10 Nm (7 ft lb)  
   M8   20 Nm (15 ft 
lb)  
Oil pan (lower part) to oil 
pan (upper part)  M6   10 Nm (7 ft lb)  
Oil pan to transmission   M8   25 Nm (18 ft 
lb)  
   M10   45 Nm (33 ft 
lb)  
Coolant line to oil pan      10 Nm (7 ft lb)  
Oil drain plug in oil pan 
(lower part)     30 Nm (22 ft 
lb)  
     
Component  
  
Tightening 
torque  
Dipstick tube to cylinder 
head  M6  
M8  10 Nm (7 ft lb)  
25 Nm (18 ft 
lb)  
Oil pump to engine block      25 Nm (18 ft 
lb)  
Oil supply line for oil pump     10 Nm (7 ft lb)  
Pa
ge 27 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1