buttons AUDI A8 1997 D2 / 1.G AEB Engine Motronic MFI And Ignition System

24-12

Checking

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -0- and -1- to input display group number 1, and
press -Q- button to confirm input.
System in Basic Setting 1 1 2 3 4

Indicated on display (1-4 = display fields)
Note:
After selecting function 04, the ECM initiates the following:
Continue with the test only when the operating conditions in display field 4
are satisfied.
EVAP canister purge regulator valve is closedA/C compressor is switched of
f
-
Briefly raise engine speed (acceleration burst) and let engine run at idle
Pa
ge 17 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-13

- Compare display with specified values (display
fields 1-4):

Display fields

1 2 3 4
Display group 1: Engine idle speed
Display xxxx RPM
xxx.x C
xx.x% xxxxxx
Indicates Idle speed Engine Coolant
Temperature (ECT) Oxygen sensor control Adjustment
conditions
Range 0-6800 RPM
(in 40 RPM steps) --- -25.0 to 25.0 % ---
Specified
value 760-960 RPM
80.0 -105.0 C
In the range from -10.0 to 10.0 %,
the value must change by at least
2 % 111111

If not as specified Page 24
-99
,
Throttle valve control module,
checking
--- If not as specified Page 24
-99
,
Throttle valve control module,
checking
Explanation
Page 24
-15

If displayed values are OK (as specified):

- Press -C- button.

- Press buttons -0-, -5- and -6- to input display
group number 56, and press -Q- button to
confirm input.
Pa
ge 19 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-14

- Compare display with specified values (display
fields 1-4):
Display fields

1 2 3 4 Display group 56: Engine idle speed
Display xxxx RPM xxxx RPM x.xx g/s xxxx
Indicates Engine speed
(actual) Engine
speed
(specified) Mass air flow
(idle speed control) Operating
conditions
Range 0-2550 RPM
(steps of 10 RPM) --- -2.80 to 4.17 g/s ---
Specified
value 820-900 RPM 860 RPM -1.11 to 1.11 g/s 0000

If not as specified Page 24
-99
,
Throttle valve control module,
checking
--- If not as specified Page 24
-99
,
Throttle valve control module,
checking
Explanation
Page 24
-16


-
Press button to advance program
sequence.
- Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
input.
Pa
ge 21 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-18

Checking

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -2- to input display group number 32, and
press -Q- button to confirm input.
Read Measuring Value Block 32 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 27 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-19

- Check oxygen sensor control learning values
(display fields 1 and 2):

Display fields

1 2 3 4
Display group 32: Oxygen sensor control learning values
Display xx.x % xx.x %
Indicates Oxygen sensor control learning value at idle
(additive)
(before TWC) Oxygen sensor control learning value at partial load
(multiplicative)
(before TWC)
Range -26.0 to 26.0 % -25.0 to 25.0 %
Specified
value -8.0 to 8.0 %
(can vary slightly) -8.0 to 8.0 %
(can vary slightly)
If not as specified Page 24
-22
, Evaluation of display group 32

If displayed values are OK (as specified):

- Press -C- button.

- Press buttons -0-, -3- and -3- to input display
group number 33, and press -Q- button to
confirm input. Read Measuring Value Block 33

Indicated on display (1-4 = display fields)
Pa
ge 28 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-21

Continuation
If the value in display field 1 is NOT OK, or if the
value does not fluctuate by at least 2 %:

- Road test to condition oxygen sensor (eliminate
possible contamination) and repeat test.
If the value in display field 1 is still NOT OK, or if
it still does not fluctuate by at least 2 %:

- Check Oxygen Sensor (O2S) heater Page 24
-
27
.
If the value in display field 1 remains constant:

- Check oxygen sensor voltage (display field 2).

-
Press button to advance program
sequence.
- Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
input.

- Switch ignition off.
Pa
ge 31 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-28

Checking

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -4- and -1- to input display group number 41, and
press -Q- button to confirm input.
Read Measuring Value Block 41 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 40 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-29

- Compare display and specified values (display
fields 1 and 2):

Display fields

1 2 3 4
Display group 41: Oxygen Sensor (O2S) heating
Display
xx.x
Htg.bC.ON/Htg.bC.OFF
xx.x
Htg.aC.ON/Htg.aC.OFF
Indicates Resistance of oxygen
sensor heater
(before TWC) O2S heater on
or
O2S heater off
(before TWC) Resistance of oxygen
sensor heater
(after TWC) O2S heater on
or
O2S heater off
(after TWC)
Range
0.0-65.0
--- --- ---
Specified
value 4.9-19.9
Htg.bC.ON --- ---

If not as specified Page 24
-30
, Continuation
--- ---
If displayed values are OK (as specified):

-
Press button to advance program
sequence.
-
Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
Pa
ge 41 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-36

Function test

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -6- to input display group number 36, and
press -Q- button to confirm input.
Read Measuring Value Block 36 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 50 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1

24-44

Checking

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -4- and -1- to input display group number 41, and
press -Q- button to confirm input.
Read Measuring Value Block 41 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 59 of 135 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.1