torque AUDI A8 1998 D2 / 1.G ATQ Engine Check DTC Memory And Erase DTC Memory Workshop Manual

01-42

DTC
DTC text
Corrective action
SAE
VAG


P1335 17743 Engine torque monitoring 2
Control limit exceeded
2) 3)
- Check hose setup
- Check Intake Air Temperature (IAT) sensor Page
28
-14

P1336 17744 Engine torque monitoring
Control limit exceeded - Check Mass Air Flow (MAF) sensor Page 24
-56
- Check coolant temperature sensor Page 28
-23
P1337 17745 Bank 1, Camshaft Position (CMP) sensor -
G163
Short circuit to Ground (GND)
1) - Check Camshaft Position (CMP) sensor Page 28
-45
P1338 17746 Bank 1, Camshaft Position (CMP) sensor -
G163
Open circuit / short circuit to B+
1)
P1340 17748 Camshaft Position (CMP) / crankshaft position
sensor
Incorrect allocation
1)
- Check phase position of Camshaft Position (CMP)
sensor Page 28
-50

P1347 17755 Bank 2 Camshaft Position (CMP) / crankshaft
position sensor
Incorrect allocation
1)


1) For these malfunctions, ECM does not switch on the Malfunction Indicator Lamp (MIL) unless malfunction is recognized
again after another engine start. Meaning of Malfunction Indicator Lamp (MIL) Page 01
-3 .
Pa
ge 33 of 52 Check DTC Memor
y (function 02
) and Erase DTC Memor
y (function 05
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.01.2

01-52

DTC
DTC text
Corrective action
SAE
VAG


P1603 18011
Control module faulty
1)
- Replace Engine Control Module (ECM) Page 24
-21
P1604 18012
Control module faulty
2) 3)


P1606 18014 Rough terrain info/engine torque
from ABS control module
Electrical malfunction in circuit
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Check wire connection between Engine Control Module (ECM) and
ABS control module (powertrain databus) Page 24
-192

P1609 18017 Crash shut-off was triggered
(Crash triggered)
5) Repair Manual, Body
-On Board Diagnostic (OBD), Repair Group 01;
On Board Diagnostic (OBD) of airbag system

- Erase DTC memory of the Engine Control Module (ECM) after output
Diagnostic Test Mode (DTM) of the airbag system Page 01
-15

1) For these malfunctions, ECM does not switch on the Malfunction Indicator Lamp (MIL) unless malfunction is recognized
again after another engine start. Meaning of Malfunction Indicator Lamp (MIL) Page 01
-3 .
2) For these malfunctions, ECM switches on the EPC warning lamp in instrument cluster. Significance of EPC warning lamp
Page 24
-136
.
3) For these malfunctions, the Engine Control Module (ECM) switches on the Malfunction Indicator Lamp (MIL) in the
instrument cluster immediately after recognizing the malfunction. Meaning of Malfunction Indicator Lamp (MIL) Page 01
-3 .
5) DTC is stored upon appropriate signal from airbag control module, also during output Diagnostic Test Mode (DTM) of the
airbag system.
Pa
ge 48 of 52 Check DTC Memor
y (function 02
) and Erase DTC Memor
y (function 05
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.01.2