AUDI A8 1999 D2 / 1.G AHA Engine Multiport Fuel Injection And Ignition System Workshop Manual

24-124

Leak Detection Pump (LDP), checking


Note:
Component locations page 24
-1

Electrical testing

If resistance is NOT OK: - Disconnect harness connector for LDP -V144-.
- Connect multimeter US1119 (Fluke 83 or equivalent) and check
resistance at leak detection pump. Specified values:

Connector terminal 1 to terminal 3: 640-720

Connector terminal 2 to terminal 3: 11.0-21.0
- Replace leak detection pump -V144-.
Pa
ge 161 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-125

Voltage supply, checking

If LED tester does not light: - Disconnect harness connector for LDP -V144-.
- Connect VAG1527B LED voltage tester between connector terminal 3
(B+) and engine Ground.
- Start engine and run engine at idle.
LED must light up.
- Check fuse for LDP -V144-.
- Check wiring for open circuit between terminal 3 and fuse, according to
wiring diagram.

Specified value: max. 0.5 .- Check fuel pump relay and signal to relay page 24
-95
.
Pa
ge 162 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-126

Intake air system, checking for leaks


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
Engine leak detector spray G 001 800 A1

Notes:
If there are leaks, intake manifold vacuum will
draw in the leak detector spray with outside air.
The spray reduces the ability of the fuel/air
mixture to ignite, which causes a drop in engine
speed and a significant increase in CO-content.
Observe the safety precautions listed on the
container.

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
Pa
ge 163 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measuring Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -0- and -1- to input display group number 1 (001),
and press -Q- button to confirm input.
Pa
ge 164 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-127

Read Measuring Value Block 1 1 2 3 4

Indicated on display (1-4 = display fields)
- Monitor oxygen sensor control in display fields 3 and 4.

Display fields

1 2 3 4
Display group 1: Engine idle speed
Display xxxx RPM
xx.x C
xx.x% xx.x %
Indicates Idle speed
(in 40 RPM
steps) Engine Coolant Temperature
(ECT) Oxygen Sensor (O2S)
control, Bank 1 Oxygen Sensor (O2S)
control, Bank 2
Range 0 - 6800 RPM
-48.0 - 143.2 C
(-54 - 289 F)
-25.0 to +25.0 % -25.0 to +25.0 %
Specified
value 620 - 740
RPM
(all-wheel
drive) --- -10.0 to +10.0 %
value must change by at
least 2 % -10.0 to +10.0 %
value must change by at
least 2 %
740 - 860
RPM
(front-wheel
drive)
- Systematically spray parts of intake air system with engine leak detector spray.
Pa
ge 165 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

If engine speed drops, or the values displayed for oxygen sensor control change:
- Check for leaks in area of intake air system most recently sprayed, and eliminate leaks.
Pa
ge 166 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1