checking oil AUDI A8 2000 D2 / 1.G AHA Engine Motronic Ignition System Workshop Manual

28-21

Ignition coils and power output stage,
checking


Notes:

The ignition coils and power output stage are
one component.
Measuring the primary resistance of the ignition
coils is not possible.
Measure secondary resistance first with ignition
wires connected to the ignition coil via the spark
plug connector of the respective cylinder (with
this method the interference resistances of the
ignition cables are also measured).
Component locations page 24
-1

Required special tools and test equipment

Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit

Test conditions
No fuel injector malfunction stored in DTC
Pa
ge 25 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-23

Checking ignition coils -N-, -N128- and -N158-


- Disconnect 5-pin connector from ignition coil
assembly.

- Remove ignition wires from spark plugs.

If resistance is NOT OK: - Using multimeter and adapters from VAG1594 connector test kit,
measure resistance between both spark plug connectors of respective
ignition circuit (across coil).

Specification: approx. 18-25 k .- Remove ignition wires from ignition coils and measure resistance
between ends of respective ignition wires.

Specification: approx. 4.0-6.0 k
Pa
ge 29 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-25

Checking signal for power output stage

- Remove connectors from all 6 injectors (DTC
memory will have to be checked and erased
later).

- Switch ignition on.

If LED flashes: - Connect LED tester VAG1527 between engine ground and connector
terminal 3.
- Crank starter for several seconds.
LED in voltage tester must flash.
- Repeat test on 5-pin connector terminals 4 and 5.
- Replace ignition coils -N-, -N128- and -N158- with power output stage -
N122-.
Pa
ge 31 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-27

Checking ground for power output stage

- Disconnect 5-pin connector from ignition coils.

If LED does not light up:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Connect VAG1527 LED voltage tester between B+ and terminal 2
(ground) of connector.
LED in tester must light up.
- Check wires for open circuit per wiring diagram.
Pa
ge 33 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1

28-28

Checking voltage supply of ignition coils

Test requirement

Fuse for ignition coils OK

- Disconnect 5-pin connector from ignition coils.

- Switch ignition on.

If LED does not light up:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Connect VAG1527 LED voltage tester between engine ground and
terminal 1 (B+) of connector.
LED in tester must light up.
- Check wires for open circuit per wiring diagram.
- Check fuse for ignition coils.
Pa
ge 34 of 34 Motronic i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.28.1