ignition AUDI A8 2000 D2 / 1.G AHA Engine On Board Diagnostic User Guide

01-53

Test sequence

- Connect VAG1551/VAG1552 scan tool and
insert "Engine Electronics" address word 01
(ignition on) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -3- to select "Output Diagnostic Test Mode"
function 03.
Rapid data transfer
Q
03 - Output Dia
gnostic Test Mode

Indicated on display
Fuel injectors:
- Press -Q- button to confirm input.
Output Diagnostic Test Mode Cylinder 1 Fuel In
jector-N30

Indicated on display
Note:
The fuel pump relay must be activated, the fuel pump must run, and you
must clearly hear the flow of fuel in the fuel pressure regulator. If the fuel
pump does not run, check fuel pump relay and connections page 24
-
95
.
- Operate throttle valve at throttle body.
As soon as the Closed Throttle Position (CTP) switch opens, cylinder 1
fuel injector must be actuated (click) 5 times.
Pa
ge 73 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-57

Valves -1- and -2- for camshaft adjustment, -
N205-, -N208-:

-
Press button.Output Diagnostic Test Mode Camshaft Adjustment 1

Indicated on display
Valves 1 and 2 for camshaft adjustment, -N205- and -N208-, are actuated
(click) until pressing the button to advance the program sequence and
end the output DTM.
If one of the valves is not actuated (does not click): - Check valves for camshaft adjustment page 28
-29
-
Press button.
Rapid data transfer
HELP
Select function XX

Indicated on display
Note:
Before selecting "Output Diagnostic Test Mode" function 03 again, switch
off the ignition for approx. 20 seconds.
Pa
ge 77 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-58

Basic Setting (scan tool function 04)


Notes:

The specified values for the "Basic Setting" and
"Read Measuring Value Block" functions are
described in the respective component test
descriptions.
Disconnecting the battery or the Engine Control
Module (ECM) harness connector will erase all
learned values and the readiness code.
Diagnostic Trouble Code (DTC) memory,
however, will not be erased. After reconnecting
the battery and/or the ECM, the engine may idle
unevenly and there may be some temporary
loss of driveablity. If so, let the engine run at
idle for a few minutes until the learning process
has been completed.
No learning will take place if a malfunction
affecting engine regulation is stored in DTC
memory (this does not include sporadic
malfunctions).
Basic settings are established with the engine
running.
In "Basic Setting" display groups 60 or 98, with
the engine stopped and the ignition switched
Pa
ge 78 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-67

VAG1598/22 test box, connecting


Notes:

Switch the ignition off and wait at least 10
seconds before disconnecting the Engine
Control Module (ECM) harness connector.
Disconnecting the battery or the Engine Control
Module (ECM) harness connector will erase all
learned values and the readiness code.
Diagnostic Trouble Code (DTC) memory,
however, will not be erased. After reconnecting
the battery and/or the ECM, the engine may idle
unevenly and there may be some temporary
loss of driveablity. If so, let the engine run at
idle for a few minutes until the learning process
has been completed.

- Switch ignition off.

- Disconnect ECM.

- Connect VAG1598/22 adapter cable to ECM
harness connector.

- Generate readiness code page 01
-73
.

Note:
Pa
ge 93 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-68

Engine Control Module (ECM), replacing


Notes:

Switch the ignition off and wait at least 10
seconds before disconnecting the Engine
Control Module (ECM) harness connector.
Disconnecting the battery or the Engine Control
Module (ECM) harness connector will erase all
learned values and the readiness code. After
reconnecting the battery and/or the ECM, the
engine may idle unevenly and there may be
some temporary loss of driveablity. If so, let the
engine run at idle for a few minutes until the
learning process has been completed page 01
-58
.

After installation of a new ECM, set ECM
coding and carry out adaptation of the throttle
valve control module -J338-.
If the ECM has been replaced, carry out the
following steps in the sequence listed.

- Connect VAG1551/VAG1552 Scan Tool (ST)
and press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with ignition
switched on) page 01
-8 .
Indicated on display (ECM identification and coding)
Pa
ge 95 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-69

-
Press button.Rapid data transfer HELPSelect function XX

Indicated on display
Note:
If the DTC memory has been erased or the ECM was disconnected from
its power supply, a new readiness code must be generated page 01
-
73
. - Switch ignition off.
- Replace faulty ECM.
- Check ECM coding page 01
-12
.
- Carry out adaptation of throttle valve control module -J388- to ECM
page 24
-150
.
- Generate readiness code page 01
-73
.
Pa
ge 97 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1