ESP AUDI A8 2018 Owners Manual

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value. It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dea ler or authorized
Audi Service Facility. Read and follow the instruc ­
tions for use on the packaging.
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of poi­
sonin g.
@ For the sake of the environment
- Preferab ly purchase environmenta lly-friend­
l y cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve­
h icle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect.
Before washing, r inse
off heavy deposits with
p lenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
A lso, wash the underside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash­
er , al ways fo llow the operating instructions pro­
vided with the press ure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
306
seals on the side windows, doors, lids or the sun­
roof* or at tires, rubber hoses, insulating materi ­
a l, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozz les or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °C) .
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshie ld wipers are
off . Follow instruc ­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Only use car washes where the vehicle remains
stationary and the washing equipmen t moves
around the vehicle when washing and drying. Car
washes that move the vehicle t hrough the car
wash using a chain are not recommended .
Washing by hand
Clean the vehicl e starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent -free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi ­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply t he product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse t he ve hicle thoroughly with wate r. Then
clean using a neutral shampoo and a soft micro ­
fiber clot h.
R inse the vehicl e thoroughly again and let it air
dry. Remove any water residue using a chamois.
..,..

Care and cleaning Component Situation Solution
Exhaust tail pipes
Road salt Water, cleaning solution suitab le for stainless steel, if nee-
essary
Decorative parts/ Deposits Mild
soap solution al, a cleaning solution suitab le for stain-
Trim less stee l, if necessary
Paint Paint damage Refer to t he paint number on the vehicle data label, repair
with touch up
paint ~ page 333
Spilled fuel Rinse
with water immediately
Surface rust Rust remover, then protect with hard wax; for questions,
consult an author ized Audi dealer or authorized Aud i Serv-
i ce Facility.
Corros ion Have it removed by an authori zed Aud i dea ler or author-
ized Audi Service Fac ility.
Water no longer Pr
otect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat wit h suitable polish; then apply paint protectant if
pa int has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith water immediately and remove with a micro-
sects, bird dropp ings, f iber cloth
tree sap and road salt
Grease -based con- Remove immediately with a mild soap solution
al and a
taminants such as soft cloth
cosmetics or sunb lock
Carbon parts Deposi ts clean the same way as painted parts ~ page 306
al Mild soap so lution: maxim um two tabl espoo ns o f neu tra l s oap i n 1 quart Cl li te r) of wate r
Interior cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild
soap solutional
Trim
Plastic parts
Deposits Damp clo1th
Heavier deposits Mild
soap solution
al, detergent-free p lastic clean ing solu -
tion, if ne cessary
Displays Deposits Soft cloth with LCD cleaner
Controls Deposits Soft
brush, then a soft cloth with a mild soap so lution a>
Safety belts Deposits Mild soap solution al, allow to dry before letting them re -
tract
308

u. co .... N
" N .... 0 0 :c ' Care and cleaning
Component Situation Solution
Te xtiles
Deposits adhering to Vacuum cleaner
artificial leather, the surface
Alcantara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
O il-based deposits Apply a m ild soap solution
al, blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such
Specia l stain remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mi ld soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc .
Natural leather Fresh stains Cotton cloth with a mi
ld soap solution a>
Water-based deposits Fresh stains : absorbent cloth
such as coffee, tea, dried stains: stain remover suitable for leather
b lood , etc.
Oi l-based deposits Fresh sta ins: absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc . dried stains: oil cleaning spray
Special deposits such Spot
remover suitable for leather
as ink, nail polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply conditioning cream that protects from
light and penetrates into the material. Use specially-c ol-
ored conditioning cream, if necessary .
Refrigerator Dust and dirt Clean the ventilation openings in the luggage compart-
ment
Deposits Lukewarm
water, mild soap solution if
necessarya>, then
dry
Defrosting Empty the refrige rato r, switch it off and let it thaw with
the door open, t hen dry
Carbon parts Deposits clean the same way as plast ic parts
• > Mi ld s oap so lution: maxim um two tablesp oon s of neu tra l soap in 1 quar t (1 lite r) of wat er
A WARNING
Th e windsh ie ld may not be treated with wa­
ter-repelling windshi eld coating agents. Un­
favorable conditions such as wetness, dark­
ness, or lo w sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
-Headlights/tail lights
-
- Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcoho l, because they could cause
cracks to form .
-Wheels
- Never use any paint polish or other abra-
sive materials.
309

Emergency assistance
Emergency assistance
General information
.,. Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
.,. Set up the warning triangle r=;,page 312 .
.,. Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
Applies to: vehicles with warning triangle
Fig. 270 L uggage co mpartm ent lid : w arnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
.,. To remove the warning triangle, press the fas-
tener in the direction of the arrow and fold the
holder down.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genuine Accessories program.
312
Vehicle tool kit
Applies to: vehicles with vehicle toot kit
Fig. 271 Lu gg age compartment : cargo floor cove r folded
upward
Fig. 272 Luggage compartment: examp le of vehicle toot
kit and vehicle j ack
The vehicle tools and vehicle jack* are stored in
the luggage compartment under the floor cover .
.,. Lift the cargo floor by the plastic handle .
.,. Hook the handle into the luggage compartment
seal
r:;, fig. 2 71 .
.,. Turn the handwheel counter-clockwise and re ­
move it .
.,. Remove the spare tire* to access the vehicle
tool kit
~ fig. 271 .
Depending on the equipment , the veh icle tool kit
may be located under the spare tire, under an­
other cover or in the tool box.
The position of the vehicle jack* may vary .
A WARNING
Improper use of the veh icle jack can cause se­
rious personal injuries.
-Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you
..,.

Fuses and bulb s
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned out
bulbs for you .
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­ moved before you are able to get to the bulb .
This applies espec ially to the light bulbs in the
front of your car wh ich you can only reach
through the engine compartment .
Sheet metal and bulb ho lders can have sharp
edges that can cause ser ious cuts, and parts
must be co rrectly taken apart and then p roperly
put back together to help prevent breakage of
parts and long term damage from water that can
enter housings that have not been properly re ­
sea led.
F or your safety, we recommend that you have
your authorized Audi dealer replace any bu lbs for
you, since your dealer has the proper tools, the correct bulbs and the expertise.
Ga s di sc ha rge la mp s (Xe non ligh ts):
Due to the high electrical voltage, have the bulbs
replaced by a qua lified techn ic ian . Head lights
with Xenon light can be identified by the high
voltage sticker.
LED headlights* requ ire no maintenance. P lease
contact your authorized Aud i dealer if a bulb
needs to be replaced.
A WARNING
Contact w it h high -vo ltage components of the
electrical system and improper rep lacement
of gas disc harge (Xenon) head light bu lbs can
cause serious personal injury and death.
- Xenon bulbs are pressurized and can ex ­
plode when being changed.
- Changing Xenon lamps requires the special
training, instructions and equipment.
- Only an a uthorized Audi dea ler or other
qualified workshop s hou ld change the bulbs
in gas disc harge lamps .
326
A WARNING
There are parts with sharp edges on the open­
ings and on the bulb holders that can cause
serious cuts .
- If you are uncertain about what to do, have
the work performed by an author ized Audi
dealer or other qual ified workshop . Ser ious
pe rsonal inju ry may resu lt from improperly
pe rformed wor k.
(D Tips
- If you must replace the light bulbs yourself,
always remember that the eng ine compart­
ment of any vehicle is a hazardo us a rea to
work in. Always read and heed all WARN­ INGS
~ page 272.
-It is best to ask you r author ized Audi dea le r
w henever you need to change a bulb.

Consumer Information
Consumer Information
Warranty coverages
Your Audi is covered by the following warran­
tie s:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Con trol Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warranties
can be found in your
Warranty & Maintenance
booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulati ons in the United States and
Canada require that automobi les meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U.S.A. and Cana ­
da differ from vehicles sold in other countries.
If you plan to take your vehicle outside the conti­
nenta l limits of the United States or Canada,
there is the possibility that:
- un leaded fue ls for vehicles with catalytic con­
verter may not be available;
- fuel may have a conside rably lower octane rat­
ing . Improper fuel may cause engine damage;
- se rvice may be inadequate due to lack of proper
service facilities, tools or testing equipment;
- r eplacement parts may not be readily available.
- Nav igat ion systems for veh icles built for the
U .S .A . and Canada w ill not necessarily work in
Europe, and may not wo rk in other count ries
outside North America.
336
@ Note
Audi cannot be responsib le for mechanical
damage that could resu lt from inadequate
fuel, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and Litera ­
ture are published as soon as poss ible after mod­
el introduction. Se rvice manuals and literature
are available to order from the Audi Technical Lit ­
erature Ordering Center at:
www.audi.techliterature.com
Maintenance
General
Your vehicle has been designed to help keep
maintenance requirements to a minimum. How­
ever, a certain amount of regular maintenance is
still necessary to assure your vehicle's safety,
economy and reliability . For detailed vehicle
maintenance consult your Warranty & Mainte­
nance booklet .
Under difficult operating conditions, for exam­
ple at extremely low outside temperatures, in
very dusty regions, when towing a trailer very fre­
quently, etc. , some service wo rk shou ld be per­
fo rm ed between the intervals specified. This ap­
plies particularly to:
- oil changes , and
- cleaning or replac ing the a ir filter .
@ For the sake of the environment
By regularly maintain ing your vehicle, you
help make sure that em iss ion standards are
maintained, thus minimizing adverse effects
on the enviro nment .
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems, and
the generally increasing technica l complexity of
.,,.

u. co .... N
" N .... 0 0 :c ' today's automobiles, have steadily reduced the
scope of maintenance and repairs which can be
carried out by veh icle owners.
Al so , sa fet y a nd
en vironmental
concerns place very strict limits
on the nature of repairs and adjustments to en­
g ine and transm ission parts wh ich a n owner can
perform .
Maintenance, adjustments and repairs usually re­
qu ire special tools, test ing devices and other
equ ipment available to specially trained work ­
shop personnel in order to assure proper per­
formance, re liability a nd safety of the veh icle and
its many systems .
Improper maintenance, adjustments and repairs
can impair the operation and reliab il ity of your
ve hicle and even void your veh icle warranty .
Therefo re, proof of se rvicing in accordance w ith
the ma intenance schedule may be a condition fo r
upho ld ing a possib le warranty claim made within
the warranty period.
Above all , ope rational safety can be adversely af­
fected, creating unnecessa ry risks fo r yo u and
your passengers.
I f in do ubt about any servicing, have it done by
your author ized Audi dealer or any other prope rly
eq uipped and qua lified workshop. We strongly
u rge yo u to g ive your author ized Audi dealer the
opportunity to perform a ll scheduled mainte ­
nance and necessary repairs. Your dealer has the
facilities, original parts and trained specialists to keep your veh icle running properly .
Pe rforming limit ed maint enanc e yourself
The fo llowing pages describe a limited number of
procedures which can be performed on your ve hi­
cle with ordinary tools, should the need arise and
trained personnel be unavailable. Before per­
forming any of these procedures, always thor­
oug hly read a ll of the app licable text and careful­
ly follow the instructions g iven . Always rigorously
observe the
W ARNINGS prov ided .
Before you check an ything in the eng ine com ­
partment , alw ays read and he ed all WARNINGS
c:> &. and c:> &. in Working in the engine compart­
ment on page 2
72 .
Con sum er In form ation
A WARNING
--
- Ser ious personal injury may occur as a result
of improperly performed maintenance, ad ­
justments or repairs .
- Always be extremely careful when work ing
on the vehicle . Always follow commonly ac­
cepted safety practices and general com­ mon sense. Never risk pe rsonal inj ury.
- Do not attempt any of the maintenance,
checks or repairs described on the following pages if you are not fu lly famil iar with these
or other proced ures with respec t to the ve­
h icle, or are uncerta in how to pro ceed.
- Do not do any work without the proper tools
and eq uipment. Have the necess ary wo rk
done by your authorized Audi dealer or an­
other proper ly equipped and qualified work­
shop.
- The engine compartment of any motor vehi ­
cle is a potentially hazardous area . Never
reach into the area around or touch the radi­
ator fan.
It is temperature controlled and
can switch on suddenly - even when the en­
g ine is off . The radiator fan switches on au­
tomatically when the coolant reaches a cer­
tain tempe rature and will cont inue to run
until the coolant temperature d rops.
- Always sw itch off the ignition before anyone
gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work underneath
the vehicle. The jack suppl ied with the veh i­
cle is no t adequate for this pu rpose and
could collapse caus ing serious personal in­
jury.
- If you must wor k unde rne ath the vehicle
with the wheels on the ground, always make
sure the vehicle is on level ground, that the
wheels a re always sec urely blocked and that
the engine cannot be started.
- Always make sure the transmission se lector
lever (automatic transmiss ion) is in
"P"
(Park position) and the pa rk brake is ap­
plied.
337

u. co .... N
" N .... 0 0 :c ' -The manufacturer cannot be held liable for
damage which occurs due to fai lure to com­
p ly wit h these st ipulat ions .
Technical Modifications
Our guidelines must be complied with when tech­
nical modifications are made.
A lways consult an author ized A udi dealer b efore
starting work on any modifications .
This will he lp e nsu re that veh icle function, pe r­
forma nce and safety are not
impa ired ¢.&, .
Attempting to work on electron ic components
and the software used w ith them ca n cause ma l­
functions . Because of the way electron ic compo­
n ents are inte rconnected with each other, such
malfunct ions can also have an adve rse effect on
other systems that are not directly involved. This
means that you risk both a substantia l reduction
in the operationa l safety of your vehicle and an
increased wear of vehicle
parts ¢.&, .
Authorized Audi dealers wi ll per form this work in
a professional and competent manner or, in spe­
cial cases, refer you to a professional company
that spec iali zes in such modifications.
A WARNING
Improper repairs and mod ificat ions can
change the way veh icle systems work and
cause damage to the veh icle and ser ious per­
sonal injury .
@ Note
If emergency repa irs must be performed else­
where, have the vehicle examined by an au­ thor ized Audi dealer as soon as possible.
Con sum er In form ation
Declaration of
Compliance, Telecom­
munication or Electronic
Systems
Radio Frequency Devices and Radiocommunica­
tion Equipment User Manual Notice .
The manufacturer is not responsible for any radio
or TV interference caused by unauthorized mod i­
ficat ions to this equipment.
D ev ices
T he following dev ices each comply wi th FC C P art
15. 19, FCC 15 .21 and RSS -Gen Issue 1:
-Adapt ive cru ise control
-Aud i side assist
-Cell phone package
-Conven ience key
-Electronic immobilizer
-Head phones
-Homelink u niversa l remote cont rol
-Remote cont rol key
-S8 plus: tire pressure monitoring system
FCC P art 15 .19
This device complies with part 15 of the FCC
Rules. Operation is subject to the follow ing two
condit ions:
(1) This device may not cause harmfu l interfer ­
ence, and
(2) this device must accept any interference re­
ceived, including interference that may ca use un­
desired operation.
FCC Part 15.21
CAU TION:
Changes or mod ificat ions not expressly approved
by the pa rty responsible for compliance could
vo id the user's aut ho rity to ope rate t he eq uip­
ment .
RSS-Gen Issue 1
Operat ion is subject to the following two cond i­
t ions:
(1) this device may not cause interference, and
3 39