oil AUDI A8 2018 User Guide

Checking and Filling
-With all these variables coming into play,
no standard rate of o il consumption can be
established or specified. There is no alterna­
tive to checking the oil level regularly and
frequently.
- If you have the impression your engine con­
sumes excessive amounts of oil, we recom­
mend that you consult an authorized Audi
dealer to have the cause of your concern properly diagnosed . Keep in mind that the
accurate measurement of oil consumption
requires great care and may take some
time. An authorized Audi dealer has instruc­
tions about how to measure oil consump­
tion accurately.
- You can find information on engine oil and
engine oil capacities for the USA at
www.audiusa.com/help/maintenance, or
for Canada at www.audi.ca/ca/web/en/
customer-area/ care-a nd-maintena nee/ aud
i­
service-schedules. html , or call
800 -822-2834.
Adding engine oil
Fig. 259 Engine co mpartment : en gin e oil fille r opening
c ove r
0 N
-N ,.:
gi
Observe the safety precautions c::, &. in Working
in the engine compartment on page
2 72.
"Turn the engine off.
" Open the hood c::, page 2 73.
" Unscrew the cap 't=?1 for the engine oil filling
opening
c::, fig. 2 59.
"Carefully add 0.S quart (0 .5 liter) of the correct
oil
c::, page 275.
"Close the engine oil filler opening cap.
"Close the engine compartment lid.
276
"Restart the ignition after two minutes and read
the current oil level in the Infota inment system
c::, page 275, Checking the engine oil level.
"Add more oil if necessary.
A WARNING
-When adding oil, do not let oil drip onto hot
engine components . This increases the risk
of afire.
- You must seal the cap on the oil filler open­
ing correctly so that oil does not leak out
onto the hot engine and exhaust system
when the engine is running, because this is
a fire hazard.
-Always clean skin thoroughly if it comes into
contact with engine oil.
- Engine oil is poisonous and must be kept
out of reach of children.
- Store the engine oil securely in the original
container.
(D Note
- If the message l!I Oil level is too full.
Please reduce oil level. appears, there is too
much oil in the engine and there is a risk of
catalytic converter and engine damage. Do
not start the engine . Contact an authorized
Audi dealer or authorized Audi Service Fa­
cility to have excess engine oil extracted if
necessary.
- Your Limited New Vehicle Warranty does
not cover damage or malfunctions due to
failure to follow recommended mainte­
nance and use requirements as set forth in
the Audi Owner's Manual and Warranty & Maintenance booklet.
- Use only a high quality engine oil that ex­
pressly complies with the Audi oil quality
standard specified for your vehicle's engine .
Using any other oil can cause serious engine
damage .
- Do not mix any additional lubricants into
the engine oil. Damage caused by such addi-
tives is not covered by the warranty.
.,._

u. co .... N
" N .... 0 0 :c ' @ For the sake of the environment
-Oil should never enter the sewer system or
come into contact with the ground.
- Pay attention to legal requirements when
disposing of empty oi l containers .
Changing the engine oil
We recommend that hove your oil changed by on
authorized Audi dealer or a qualified service sta­
tion .
Before you check anyt hing in the engine compart ­
ment,
alw ays re ad and h eed all W ARNINGS ¢ &
in Working in the engine comportment on
page 272.
The engine oil must be changed according to the
intervals specified in your Warranty
& Mainte­
nance booklet . This is very important because the
lubricating properties of oil diminish gradually
during normal vehicle use.
Under some circumstances the engine oi l should
be changed more frequently. Change oil more of­
ten if you drive mostly short distances, operate
the vehicle in dusty areas or under predominantly
stop-and-go traffic condit ions, or have your vehi­
cle where temperatures remain below freezing
for extended periods .
Detergent additives in the oil will make fresh oil
look dark after the engine has been running for a
short t ime . Th is is normal and is not a reason to
change the oil more often than recommended .
Because of the problem of proper disposal, along
with the special tools and necessary expertise re­
qu ired, we strongly recommend that you have
your oil changed by an authorized
A ud i d ea ler or
a qualified se rvice station .
If you choo se to chang e your o il y ou rse lf, please
note the following important information:
A WARNING
T o reduce the r isk of personal injury if you
must change the engine oil in your ve hicle
yourse lf:
- Wear eye protection .
-
Check ing and F illing
- To reduce the risk of burns from hot engine
oil, let the engine cool down to the touch.
- When removing the oil drain p lug with your
fingers, stay as far away as possible. Always keep your forearm parallel to the ground to
help prevent hot oil from running down your
arm.
- Drain the oil into a container designed for
this purpose, one large enough to hold at least the total amount of oil in your engine.
- Engine oil is poisonous. Keep it well out of
the reach of children .
- Continuous contact with used engine o il is
harmful to your skin. Always protect your
skin by wash ing oil off thoroughly with soap
and wate r.
@ Note
Never mix oil additives with your engine oil.
These add itives can damage your engine and
adversely affect your Audi L imited New Vehi­
cle War ranty .
@ For the sake of the environment
-Before chang ing your o il, first make sure
you know where you can properly d ispose of
the used oil.
- Always dispose of used engine o il properly .
Do not dump it on garden so il, wooded
areas, i nto open streams o r down sewage
dra ins.
- Recycle used eng ine o il by tak ing it to a used
eng ine oi l collection fac ility in yo ur area, or
c ontact a se rvice station.
Cooling system
Coolant
The eng ine cooling system is filled w ith a mixture
of purified water and coolant additive at the fac­
tory. This coolant must not be not changed .
The coo lant level is mon itored through
the . in­
dicator
light¢ page 20. However, we do recom­
mend occasionally checking the coolant level
manually .
.,.
277

u. co .... N
" N .... 0 0 :c ' ~ At the end of the charging process, switch the
charger off and pull the power cab le out of the
socket.
~ Now remove the charg ing device terminal
clamps .
~ Close the cover @on the positive term inal and
re-install the
cover (!).
~ Close the hood c:;, page 2 73 .
A drained battery can freeze at temperatures
around
322F (0QC) . A frozen or thawed out bat­
tery must no longer be used . The battery hous ing
could be cracked by the format ion of ice , which
could cause battery acid to leak out
c:;, ,&. .
Charg ing the b attery
Only use chargers with a ma ximum charg ing
v oltage of 14 .8 V.
The battery connecting cables
do not need to be disconnected . Do not open the
battery when charg ing .
Read all of the manufacturer's instructions for
the charger before charging the battery .
A WARNING
-A h ighly exp losive mixture of gases can form
w hen cha rging batter ies. O nly charge t he
vehicle ba tte ry in well -vent ilated a reas.
- A d rained vehicle battery can freeze at tem­
peratu res a round 32
Q F (0 QC). A froze n or
thawed ve hicle battery m ust not be ch arged
and must not be used anymore. The battery
housing can crack and battery acid can leak
out if ice forms, whic h increases the risk of
an exp losion and chemical burns. Contact an
authorized Audi dealer or authorized Aud i
Service Facility for more information.
- Do not connect or disconnect the charg ing
cable while charg ing because th is increases
the risk of an explosion .
(D Tips
-Only charge the vehicle battery through the
connections in the engine compartment.
-Read all of the manufacturer's instructions
for the charger before charg ing the ve hicle
battery .
Ch eck ing and F illing
Windshield washer
system
F ig . 263 E ngin e compar tmen t: was he r fl ui d reservo ir cap
M N
-N ' "' "' m
The windshield washer fluid reservoir O contains
the cleaning solution for the windshie ld and the
headlight washer system
c:;, fig. 263, c:;, page 274.
The reservoir capacity can be found in
<=> page 334.
To reduce the risk of lime scale depos its on the
spray nozzles, use clean water with low amounts
of calcium. Always add w indow cleaner to the wa­
ter . When the outside temperatures are cold, an
anti -freezing agent should be added to the water
so that it does not freeze .
@ Note
-The concentration of ant i-freez ing agent
must be adjusted to the veh icle operat ing
condit ions in the respective cl imate . A con­
centration that is too high can lead to vehi­
cle damage.
- Never add radiato r anti-freeze or other addi­
t ives to the washer fluid.
- Do not use a glass cleaner that conta ins
paint so lvents, because t his could damage
the paint.
Service interval display
The service interval display detects when your ve­
hicle is due for service.
T he serv ice interval d isplay wo rks in two stages:
-In sp ec tio n o r oil change remind er: after a cer-
tain distance driven , a message appears in the
.,.
2 8 1

Checking and Filling
instrument cluster display each time the ign i­
tion is switched on or off . The rema ining
distance or time is displayed br iefly.
- Inspection or oil change due: if yo ur vehicle
h as reached an inspection o r oi l change interval
o r both intervals at t he same time, the mes­
sage
Inspection due! or Oil change due! or Oil
change and inspection due!
appears br iefly af­
te r switch ing the igni tion on/off .
Checking service intervals
You can check t he rema ining distance o r time un­
til the next oil change o r next inspec tion i n the
Ca r menu. To do this, select: the
IC ARI function
button
> Car systems contro l bu tton > Service &
control > Service intervals .
Resetting the indicator
A n author ized A udi dealer or authorized A udi
Serv ice Facility will reset the serv ice interval d is­
p lay after pe rforming serv ice .
I f yo u have chan ged t he oil you rself, you must re ­
set t he oil change interva l.
To reset the in dic ator, se le ct : th e
ICAR I fu nc tion
but ton
> Car system s control button > Service &
control > Service intervals. T urn t he control knob
downwa rd to
Reset oil change interval an d press
the co ntro l knob.
{QJ Note
- On ly reset the oil ch ange in dicato r if the oil
was c han ge d.
- Fo llow ing the service i nte rvals is cr itical to
maintai ning the service life a nd value o f
your ve hicl e, especia lly t he engine. Even if
the m ileage on the veh icle is low, do not ex­
c e ed th e tim e fo r th e ne xt serv ic e .
282

u. a:, .... N
" N .... 0
0
I Wheels
Wheels and Tires
General information
~check your tires regularly for
damage (punctures, cuts, cracks
and bulges). Remove foreign ob­
jects from the tire tread.
~ If driving over curbs or similar
obstacles, drive slowly and ap ­
proach the curb at an angle.
~Have faulty tires or rims re­
placed immediately.
~Protect your tires from oil,
grease and fuel.
~Mark tires before removing
them so that the same running
direction can be maintained if
they are reinstalled.
~Lay tires flat when storing and
store them in a cool, dry location
with as little exposure to light as possible.
(D Note
-Please note that summer and winter tires are designed for
the conditions that are typical in those seasons. Audi recom­
mends using winter tires dur­
ing the winter months. Low
temperatures significantly de­
crease the elasticity of summ­
er tires, which affects traction
Wheels
and braking ability. If summer
tires are used in very cold
temperatures, cracks can form on the tread bars, resulting in
permanent tire damage that
can cause loud driving noise
and unbalanced tires.
-Burnished, polished or chromed rims must not be
used in winter driving condi­
tions. The surface of the rims does not have sufficient corro­
sion protection for this and
could be permanently dam­
aged by road salt or similar
substances.
Tire designations
Fig. 264 Tire specification codes on the
sidewall of a tire
.,.
283

Wheels
Bead
means the part of the tire that is
made of steel wires, wrapped or
reinforced by ply cords and that is
shaped to fit the rim .
Bead separation
means a breakdown of the bond
between components in the bead .
Cord
means the strands forming the
plies in the tire .
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manufac­
turer for
a tire of a designated
size that has not been driven for more than a couple of miles (kilo­
meters) at low speeds in the
three hour period before the tire pressure is measured or adjusted .
Curb weight
means the weight of a motor ve­
hicle with standa rd equipment in ­
cluding the maximum ca pacity of
fuel, oil, and coolant, air condi ­
tioning and addit ional weigh t of
optional equipment.
E x tra load tire
means a tire designed to operate
at higher loads and at higher
in -
28 6
flation pressures than t he corre­
spond ing standard tire. Extra load
tires may be identified as "X L",
"xl" , "EXTRA LOAD" , or "RF" on
the sidewall.
Gross Axle Weight Rating ("GAWR")
means the load-car rying capacity
of a single axle system , measu red
at the ti re-ground interfaces .
Gross Vehicle Weight Rating
("GVWR")
means the maximum total loaded
weight of the vehicle .
Groove
means the space between two ad­
jacent tread ribs .
Load rating (code)
means the maximum load tha t a
tire is rated to carry for a given i n­
flation pressure. You may no t find
this informat ion on all ti res be­
cause it is not required by law .
Maximum load rating
means the load rating for a tire at
the maximum permissible infla­
tion pressure for that tire .
Maximum loaded vehicle
weight
means t he sum of:

Wheels
sure that load limits are not ex­
ceeded. Vehicle load includes ev­
erybody and everything in and on
the vehicle. These load limits are
technically referred to as the vehi­
cle's
Gross Vehicle Weight Rat­
ing
("GVWR").
The "GVWR" includes the weight
of the basic vehicle, all factory in­
stalled accessories, a full tank of
fuel, oil, coolant and other fluids plus maximum load. The maxi­
mum load includes the number of
passengers that the vehicle is in­
tended to carry ("seating capaci­
ty") with an assumed weight of
150 lbs. (68 kg) for each passen­
ger at a designated seating posi­
tion and the total weight of any
l uggage in the vehicle. If you tow
a trailer, the weight of the trailer
hitch and the tongue weight of
the loaded trailer must be includ­
ed as part of the vehicle load.
The
Gross Axle Weight Rating
("GAWR") is the maximum load
that can be applied at each of the
vehicle's two axles.
The fact that there is an upper
limit to your vehicle's Gross Vehi­
cle Weight Rating means that the
total weight of whatever is being
296
carried in the vehicle (including
the weight of a trailer hitch and the tongue weight of the loaded
trailer) is limited. The more pas­
sengers in the vehicle or passen­
gers who are heavier than the
standard weights assumed mean
that less weight can be carried as l uggage .
The Gross Vehicle Weight Rating
and the Gross Axle Weight Rating
are listed on the safety compli­
ance sticker label located on the
driver's side B-pillar
¢ page 293,
fig. 266.
_& WARNING ~
Overloading a vehicle can cause
loss of vehicle control, a crash
or other accident, serious per­
sonal injury, and even death.
-Carrying more weight than
your vehicle was designed to
carry will prevent the vehicle
from handling properly and increase the risk of the loss of
vehicle control.
-The brakes on a vehicle that
has been overloaded may not
be able to stop the vehicle
within a safe distance.

u. co .... N
" N .... 0 0 :c ' & WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
-To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the braking effect may be delayed due to moisture on the
brake rotors or ice in the winter . This in­
creases the risk of an accident. The brakes
must be dried first with a few careful brake
applications.
@ Note
-If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Power folding exterior mirrors* must only
be folded in and out using the power folding
function.
-To reduce the risk of paint damage, do not
wash the vehicle in direct sunlight.
-
Care and cleaning
-To reduce the risk of damage, do not wash
the power top with a pressure washer.
-To reduce the risk of damage to the surface,
do not use insect removing sponges, kitchen
sponges or similar items.
-Matte finish painted vehicle components:
-To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax.
-Never use protective wax. It can destroy
the matte finish effect .
-Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint. The paint could be damaged
when the stickers or magnets are re­
moved .
@ For the sake of the environment
Only wash the vehicle in facilities specially de­
signed for that purpose . This will reduce the
risk of dirty water contaminated with oil from
entering the sewer system.
Cleaning and care information
When cleaning and caring for individual vehicle
components, refer to the following tables. The
information contained there is simply recom­
mendations. For questions or for components that are
not listed, consult an authorized Audi
dealer or authorized Audi Service Facility. Also
follow the information found
in~.&. -
Exterior cleaning
Component Situation Solution
Windshield wiper
Deposits ~ page 51
blades
Headlights/
Deposits Soft sponge with a
mild soap solutiona)
Tail lights
Sensors/
Deposits Sensors: soft cloth with solvent-free cleaning solution
camera lenses Camera lenses: soft cloth with alcohol-free cleaning solu-
tion
Snow/ice Hand brush/solvent-free de-icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
307
...

u. co .... N
" N .... 0 0 :c ' Care and cleaning
Component Situation Solution
Te xtiles
Deposits adhering to Vacuum cleaner
artificial leather, the surface
Alcantara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
O il-based deposits Apply a m ild soap solution
al, blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such
Specia l stain remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mi ld soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc .
Natural leather Fresh stains Cotton cloth with a mi
ld soap solution a>
Water-based deposits Fresh stains : absorbent cloth
such as coffee, tea, dried stains: stain remover suitable for leather
b lood , etc.
Oi l-based deposits Fresh sta ins: absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc . dried stains: oil cleaning spray
Special deposits such Spot
remover suitable for leather
as ink, nail polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply conditioning cream that protects from
light and penetrates into the material. Use specially-c ol-
ored conditioning cream, if necessary .
Refrigerator Dust and dirt Clean the ventilation openings in the luggage compart-
ment
Deposits Lukewarm
water, mild soap solution if
necessarya>, then
dry
Defrosting Empty the refrige rato r, switch it off and let it thaw with
the door open, t hen dry
Carbon parts Deposits clean the same way as plast ic parts
• > Mi ld s oap so lution: maxim um two tablesp oon s of neu tra l soap in 1 quar t (1 lite r) of wat er
A WARNING
Th e windsh ie ld may not be treated with wa­
ter-repelling windshi eld coating agents. Un­
favorable conditions such as wetness, dark­
ness, or lo w sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
-Headlights/tail lights
-
- Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcoho l, because they could cause
cracks to form .
-Wheels
- Never use any paint polish or other abra-
sive materials.
309

lL t:0 ....
'"" ......
'"" .... 0 0 :c ' Driver's side cockpit fuse assignment
Fig. 286 Drive r side cockpit: fuse panel with plastic bracket
Fuse panel @ (brown)
No. Equipment
1 Light switch
2 Eme rgency start coil (driver iden tification)
3 Left rear door control module
4 Head-up display
5 Horn
6 Interior lights (headliner)
Steering column lever, multifunction
8 steer ing whee l controls, steering wheel
heating
10 Powe r steering column adjustment
11 Driver door control module
12 Diagnostic con nector, light/rain sensor
14 Power steering column adjustment
lS Power steering, A/C compressor
16 Brake booster
Fuse panel © (black)
No. Equipment
1 Front seat heating
2 Windshield wipers
Fuses and bulbs
Fuse panel © (black)
3 Front exterior lighting
4 Sliding/tilting sunroof
5 Driver power window
6 Dr iver 's seat (pne umat ic)
7 Panorama glass roof
8 Dynamic steering
9 Front exterior lighting
10 Windshield/headlight washer system
11 Left rear power window
12 Panorama glass roof
Front passenger side cockpit fuse
assignment
Fig. 287 Fro nt passe nge r side cockp it: fuse panel with
plastic bracket
Fuse panel @ (black)
No. Equipment
1 Anti-theft alarm system
2 Transmission contro l module
3 Front climate control fan
4 Engine s upply
6 Engine control module
7 Front passenger door control module
323