Stop and start AUDI Q2 2021 Owner´s Manual

Driver assist systems

CO

<
O
rN rN
t-H
o <

•
To increase or reduce the speed quickly, hold
the lever towards
©/©
until the
LED ©
opage
113, Fig. 105 reaches the de­
sired cruising speed.
You can preselect the speed, even when the
adaptive cruise control is inactive, by moving the
lever in the appropriate direction ©/©. To
acti­

vate the preselected speed, pull the lever to
posi­

tion ©
^>page
113, Fig. 104.
Following any changes, the new stored speed will
be displayed briefly in the status line

opage
113, Fig. 105 ©. The indicator lamp
E53
KOI
is also lit when the adaptive cruise control is

active,
and the indicator Lamp
B3 iS Lit
when the
adaptive cruise control is inactive. The indicator

lamp El
will Light up instead in the Audi virtual
cockpit*.
Driving in congested traffic
Applies to: vehicles with Audi adaptive cruise control and au­
tomatic gearbox
The adaptive cruise control assists you when driv­
ing in congested traffic. If
a
vehicLe which has
been detected in front stops, the adaptive cruise
control applies the brakes (within the limits im­
posed by the system) and holds the vehicle at a

standstill.

•
To set the vehicle in motion again with the
adaptive cruise control, tap the accelerator

with
your foot, or

•
Pull the lever towards you to position ©

•=>
page 115, Fig. 107.
Using the adaptive cruise control to set the
vehicle in
motion1'

If the message ACC: ready to drive off is on the
display and the vehicle in front drives off, your
vehicle will automatically start moving
•=>
A. You
can reactivate the ACC: ready to drive off mes­
sage briefly by pulling the lever to position ©.
For safety reasons, your vehicle will start moving
only if
- the driver's seat belt is
buckled.

x)
Not available on vehicles for some markets.
- all the doors and the bonnet are closed,
- your vehicle has been stationary for Less than
3 minutes.

A
WARNING
If the ACC: ready to drive
offx)
message ap­

pears,
your vehicle will start moving even if
there is an obstacle between your car and the
vehicle in front - risk of accident!
© Note
If your vehicle does not start moving as ex­
pected with the adaptive cruise control, even
though the ACC: ready to drive
off1)
message
is displayed, you can set the vehicle in motion
by tapping the accelerator with your foot.
Interrupting the cruise control
Applies to: vehicles with Audi adaptive cruise control

Fig.
107 Control lever
Important: The adaptive cruise control must be

on.

Overriding the cruise control

•
To accelerate manually, pull the lever towards
you to position © and hold it in this position or
press the accelerator. The message ACC: over­
ride will appear.
• To reactivate the cruise control, release the Lev­
er or take your foot off the accelerator.
Interrupting the cruise control while driving

•
Move the lever to position ©. The message

ACC:
standby will appear. Or:
• Apply the brakes.
115

Driver assist systems
provided tempt you into taking any risks when
driving - this can cause accidents.
- Please note that pre sense front can give
warnings or apply the brakes unexpectedly.
Always secure your luggage to prevent dam­
age and possible injury.
- Due to inherent system limitations, false ac­
tivation of the system is possible.
- Please note that the sensor is not always
able to detect all objects which may repre­
sent a potential hazard - risk of accident!
- Pre sense front does not react to the follow­

ing:
oncoming traffic in the same lane, sta­
tionary or stopped persons, pedestrians
crossing the road at an angle, groups of
people, animals, or objects that are hard to

recognise •=>
A in General notes on
page 112.
A WARNING
The pre sense front functions may be restric­
ted or unavailable in situations such as the

following:

- If objects such as crash barriers or other
vehicles are reflecting additional light.
- At tunnel entrances.
- In heavy fog,
rain,
road spray or snow.
- If the radar sensor is dirty, frosted, dam­
aged or covered.
- When driving through a corner.
-Applies to: front-wheel drive vehicles: If the
ESC system has been partially or fully deac­

tivated.

© CAUTION
Impacts or damage to the bumper, wheel
arches or underbody can cause misalignment
of the sensor. This can impair the function of
the pre sense front system. Have the systems
checked by a
quaLified
workshop.
© Note
-The automatic brake application with in­
creasing brake force can be cancelled by ap­
plying the brakes yourself or by pressing the
accelerator firmly or by taking evasive ac­

tion.

- Applies to: front-wheel drive vehicles: Cer­
tain pre sense front functions are deactiva­
ted when the ESC
offroad
mode is switched
on and when reversing.
- Applies to: front-wheel drive vehicles: The
pre sense is deactivated if you restrict or
switch off the ESC
^>page
146.
Settings on the infotainment system
Applies to: vehicles with Audi pre sense front/Audi adaptive
cruise control

•
Select the following on the infotainment sys­

tem:
|MENU|
button > Car > left control button
> Driver assist > Audi pre sense.
System - The pre sense functions can be switched
on/off.
Advance
warning15
- You can switch the advance
warning off or set the warning time for pre sense
front (early/medium/late).
Start by setting the advance warning to early. If
you then find that the system warns you earlier
than desired, you can set the advance warning to

medium.
The advance warning should be set to
late only in exceptional cases, such as during very
dynamic driving.
If a system or the advance warning function is
switched off, it will be automatically activated
again the next time you switch on the
ignition15.

Driver messages
Applies to: vehicles with Audi pre sense
Audi pre sense: fault. Please contact work­
shop
This message appears if the functions of the pre
sense system are impaired. An impairment can
occur, for example, if a sensor fails. If the mes­
sage remains displayed permanently, drive to a
qualified workshop soon and have the fault
recti­

fied.
•

x)
Not available on vehicles for some markets.
122

Parking aids
- To ensure that the acoustic parking aid
works properly, the sensors must be kept
clean and free of snow and ice.

CO

< o rN
iv
rN
•-i

00
Rear parking aid
Description
Applies to: vehicles with rear parking aid

The
rear parking aid is an acoustic parking
sys­

tem.
Description
Sensors are located in the rear bumper. When
the sensors detect an obstacLe, you are alerted by
acoustic signals (beeps).
Please ensure that the sensors are kept free of
stickers, deposits and any other substances
which could impair the function of the system.
Notes on cleaning
^>page
312.
The measuring range of the sensors starts at
about:
Rear Side
Centre
0.90 m
1.60 m
The acoustic signals sound with increasing
fre­

quency as you approach the obstacle. A warning
tone will sound continuously when the vehicLe is
less than approx. 0.30 m away from the obstacLe.
Stop reversing immediately
•=>
A in General notes
on page 134,
<=>©
in General notes on page 134
The volume of the warning beeps will be reduced
after
a
few seconds until it is muted if the vehicLe
remains at a constant distance from a detected
obstacle (but not if the obstacle is closer than
0.30 m). If the tone is muted and the obstacLe
comes closer than before, the tone will sound

again.
If the tone is muted and the obstacle is
further away than before, no tone will sound.
Please watch the area surrounding the vehicle
when driving off.
Activating
The parking aid is switched on automatically
when reverse gear is engaged. You will hear a
brief acknowledgement tone.
Parking system plus
Description
Applies to: vehicles with parking system plus/park assist

The
parking system plus provides acoustic and
visual assistance when parking.

Fig.
124 Diagram
Sensors are located in the front and rear bump­

ers.
When the sensors detect an obstacle, you are
alerted by acoustic signals (beeps) and a graphic
display.
Please ensure that the sensors are kept free of
stickers, deposits and any other substances
which could impair the function of the system.
Notes on cleaning
<3>page
312.
Approximate range for each display zone:
®
®
©
®
©*
1.20 m
0.90 m
1.60 m
0.90 m

0.90
ma)

a'
Applies to vehicles with park assist
The acoustic signals sound with increasing
fre­

quency as you approach the obstacle. A warning
tone will sound continuously when the vehicLe is
less than approx. 0.30 m away from the obstacLe
(or less than approx. 0.20 m away in zone (D*).
Stop moving immediately
•=>
A in General notes
on page 134,
•=>©
in General notes on page 134
The volume of the warning beeps will be reduced
after
a
few seconds until it is muted if the vehicLe
remains at
a
constant distance from a detected
obstacLe (but not if the obstacLe is closer than
0.30 m). If the tone is muted and the obstacle
135

Parking aids

CO
< o rN
iv
rN
i—i

00
Important: For the best parking result, you
should maintain a distance of approx. 1 metre to
the row of parked cars.

•
To switch between parallel
(Â)
perpendicular
forwards
(B)
and perpendicular in reverse (?)
parking modes, turn the rotary pushbutton to
select the desired mode. The system only
shows parking modes that are currently possi­

ble.

•
Operate the turn signal. The desired side of the
road will be scanned.

•
To park parallel to the roadside, drive forwards
at not more than 30 km/h. Or:

•
To park perpendicular to the roadside, drive
forwards at not more than 20 km/h.

•
The system will display
a
parking space when it
finds one
^Fig.
137. Please check that the
parking space is suitable for your vehicle.

•
To park using the system, follow the instruc­
tions on the display.
If
you
exceed a speed of about 50 km/h, the park
assist will be switched off.
The park assist will display
a
parking space only if
it is Long and wide enough for the vehicLe.
© Note
-You can select any one of the parking op­
tions found. The potential parking space is
displayed until you have driven too far away
from it.
- You can activate the park assist after you
have already driven past a parking space (as
long as you were driving slowly enough). To
do so, press the
P©
button and operate the
turn signal.
- The system displays the right or left side of
the
road,
depending on which turn signals
you operate.
- The best parking results will be achieved if
you position the vehicle as parallel as possi­
ble to the line of parked cars or the kerb be­
fore you start the actual parking manoeu­

vre.

- If there are suitable parking spaces on both
sides of the road (for instance on a one-way
street), you can change the direction of the
turn signals to park on the other side, even
if
you
have already activated the park assist.
Starting a parking manoeuvre
Applies to: vehicles with park assist

The
driver is responsible for parking the vehicle.

Id it nl ila 1 i
L
ml\Jf '- ,H
i^*feâSi^T^,s*'ii^**£^B
'
1
Jr
r
i
fm
-
rf
"
!B—^-ASSL
^
tc^^^T-^T^^Tfr^a^j^

*
If*
Tf dl if
ïï
F ~"i
1VT"
•*-•.'' iiS^S

Fig.
138 Infotainment system: Prompt to continue revers­
ing (example: parking parallel to the roadside)

•
Drive forwards until the instructions for the au­
tomatic parking manoeuvre appear on the info­
tainment display
^>Fig.
138
^/^
in Descrip­
tion on page 139,
o(T)
in Description on
page 140. A
P
will appear in the intended park­
ing space as soon as the vehicle reaches the
correct position.

•
If necessary, you can use the rotary pushbutton
to change the parking mode in order to take a
different approach to the parking space.

•
The park assist is ready when the message
Please select reverse gear and let go of the
steering wheel appears on the infotainment
display.

•
After stopping for
a
moment, select reverse
gear.

•
Take your hands off the steering wheel.

•
Watch the
road.
When the road is clear, press
the accelerator gently
^/^
in Description on
page 139,
•=>(?)
in Description on page 140.

•
Follow the instructions on the display

^>page
142 and the acoustic warning tones
until the parking manoeuvre is complete. The
arrows on the vehicLe show the required direc­
tion of travel.
The park assist automatically steers the vehicle
into the parking space while the driver operates
the pedals. The maximum parking speed is 7 km/
h. The park assist will be deactivated if
you
drive
too fast or move the steering wheel by hand. To •
141

Intelligent technology

/r\
WARNING
You should switch on the off-road mode or
switch off the ESC/traction control system
(ASR) only if your driving ability and the traf­
fic conditions allow you to do so safely -
dan­

ger of skidding!
- The stabilising function is restricted when
off-road mode is switched on. The driven
wheels may start to
spin,
causing the
vehi­

cle to lose grip, in particular on slippery or
wet roads.
- When the ESC/traction control system
(ASR) is switched off, the vehicle will not be

stabilised.

Brakes
New brake pads
New brake pads do not give full braking effect for
the first 400 km, they must first be "bedded in".
However, you can compensate for the slightly re­
duced braking effect by applying more pressure
on the brake pedal. Avoid placing a heavy load on
the brakes during the running-in period.
Wear
The rate of wear on the brake pads depends a
great deal on how you drive and the conditions in
which the vehicLe is operated. Negative factors

are,
for instance, city traffic, frequent short trips
or hard driving with abrupt starts and stops.
Noises
Brake noise may develop in certain situations, de­
pending on the speed, braking force and ambient
conditions (such as temperature and relative hu­
midity).
Effect of moisture and salt
In certain conditions, such as in heavy
rain,
early
morning dew, or after washing the car or driving
through water, the full braking effect can be de­
layed by moisture (or in winter by ice) on the
discs and brake pads. The brakes should be
< "dried" by pressing the pedal to restore full brak-

R
ing effect.
When you are driving at higher speeds with the
windscreen wipers on, the brake pads are very
briefly brought into contact with the brake discs.
This automatic process which goes unnoticed by
the driver is carried out at regular intervals and is
intended to improve braking response in wet
con­

ditions.
The effectiveness of the brakes can also be
tem­

porarily reduced if the car is driven for some dis­
tance without using the brakes when there is a
lot of salt on the road in winter. The layer of salt
that accumulates on the discs and pads can be
removed with a few cautious brake applications.
Corrosion
There may be a tendency for dirt to build up on
the brake pads and corrosion to form on the discs
if the car is used infrequently, or if
you
only drive
low mileages without using the brakes very

much.

If the brakes are not used frequently, or if corro­
sion has formed on the discs, it is advisable to
clean off the pads and discs by braking firmly a
few times from a moderately high speed
•=> A-

Faults in the brake system
If the brake pedal travel should ever increase
suddenly, this may mean that one of the two
brake circuits has failed. Drive immediately to the
nearest qualified workshop and have the fault

rectified.
On the way to the dealer, be prepared
to use more pressure on the brake pedal and al­
low for longer stopping distances.
Low brake fluid level
Malfunctions can occur in the brake system if the
brake fluid level is too low. The brake fluid level
is monitored electronically.
Brake servo
The brake servo amplifies the pressure you apply
to the brake pedal. It only works when the engine
is running. •
147

Multi Media Interface
Press the
|BACK|
button (7)
ipage
152, Fig. 140
to return to the previous function.
Speller for
letters/numbers

Esnni
33!
ABC DE
FCHI
J
K

•
Schmidt,
area
700 m (D) Ingolstadt,
8504S AUFDERSCHANZ
<=•
700 m (D) Ingolstadt,
85049

CO

rN
IV
rN
•-i

00

Fig.
154 Illustration: Speller for letters/numbers
You can use the speller to enter letters, numbers
and symbols on the MMI. This option is available
while the entry field
(f)
is active
^>Fig.
154.
- To call up/close the speller for letters/num­

bers:
Push the rotary pushbutton upwards/
downwards while the entry field is active. Or:
Select the right control button > Open speller/
Close speller.
- To enter a letter/number: With the selection
line activated, turn the rotary pushbutton
@

^>Fig.
154
to select the desired Letter/number.
Press the rotary pushbutton to confirm the let­
ter/number. Your entry will appear in the entry
field (2). When you have entered all characters,
select and confirm button (1) to switch to the
results list. Or: Push the rotary pushbutton
downwards.
- To enter diacritics (e.g. â, ç, n, ô)*: With the
selection line activated, turn the rotary push­
button to select a letter
@
^>Fig.
154. To open
the corresponding set of diacritics, press and
hold the rotary pushbutton. Turn the rotary
pushbutton to select a diacritic while in the
character selection line
@^>Fig.
154. Press the
rotary pushbutton to apply the diacritic. To
close the set of diacritics without selecting a
character, press and hold the rotary pushbut­
ton again. Or: Select and confirm |âôû|(7)

^>Fig.
154. Select and confirm a diacritic.
- To delete a character: Use the rotary pushbut­
ton to turn the pointer to
OFig.
154, and
then press the rotary pushbutton. To delete all
characters in the entry
field,
select
and
press and hold the rotary pushbutton until all
characters have been deleted.
- To enter a special character: Select and confirm

\M\®*Fig.
154.
flâûl
(7) or
|T23l
(§).
Use the
speller for numbers to select and confirm the
special character desired (such as a hyphen or
full stop).
- Input help: In some cases (such as in the
navi­

gation system*), the system will suggest a

word*
to complete your entry while you are still
making
it@
^Fig.
154. You can confirm the
word by pushing the rotary pushbutton up­
wards.
- Results list: In some cases (such as in the direc­

tory),
the system will switch to the results List
(D
^>Fig.
154 automatically. Select and confirm
a suggestion from the List.
Requirement: The entry field (2)
^>Fig.
154 must
be active.
- To switch between the speller and the MMI
touch
pad*:
The handwriting recognition fea­
ture is automatically activated for the MMI
touch
pad*,
which means you can simply start

writing.

159

Speech dialogue system
• Telephone
• Audi connect
• Navigation
• Directory
• Radio
• Media
• Sound
• Help
• Help Speech Dialogue System
• Help Telephone
• Help Audi connect
• Help Navigation
• Help
Map

• Help Radio
• Help Media

SIIPCMI

Enter number
• Delete number
/
Correction
Directory

Call (XY)

• business
/
private
/
land line
/
mobile

NAVIGi
mm

• Navigate
to (XY)

• Start
/
stop route guidance
• Directory
• Last destinations
• Navigation favourites
• Drive home
• Enter address
• Enter country
/
town
/
street
• Exclude route
/
Exclude route
for
(XY)
km / m

• Favourites
• Call
(XY)

• Enter number
• Redial
• Read
new
text message
• Drive
me to (XY)

• Enter address
• Stop route guidance
•
Map

• Line
(XY)

• Next page
/
previous page
• Cancel
• Online destinations
•
No, I
meant
(XY)

• Correction

Call list

Redial
Call mailbox
Enter PIN
/
delete
PIN

Telephone favourites
Exclude next route section
/
Exclude
next street
Manual
/
Automatic traffic
avoidance
Route list
Calculate alternative routes
Online destinations
Special destinations
Map
Day
map /
Night
map

2D driving position
map / 2D
north position
map / 3D map /
Destination
map /
Overview
map

Flight information
/
Train information
City events
Online news
Twitter

^iuiDit(5.Q:NiNE:(aH

• Audi connect
• Travel information
/
Parking information
• Fuel prices
• Weather
RADIO MEDIA
RADIO MEDIA
• Radio favourites
• FM
and DAB

•FM/DAB/AM

• Station (XY)
/
Frequency
(XY)

• Ensemble
(XY)

• Traffic programme
on / off

Jukebox

CD/DVD

SD card
1 /
SD card
2

Audi music interface
/
iPod
/
USB
/
Bluetooth
/

Wi-Fi/Medium
(XY)

Media favourites
/
Artists
/
Albums
/
Genres
/

Tracks
/
Playlists
/
Videos
Folder
up

Random playback
on / off

Fig.
157
Overview
of
commands
00
163

Speech dialogue system
Function
Calling up a list of recent navigation
destinations
Calling up the favourites
Calling up your home address
Entering an address with assistance
from the system
Individual commands for entering a
destination
Making corrections while entering a
destination
Navigating to a contact
Navigating to a specific address
stored for a contact
Navigating to favourites
Starting route guidance when an ad­
dress card is open
Entering a new
destination/stop­

over while route guidance is active
Starting route guidance after enter­
ing a destination
Cancelling the active route guidance
Calculating alternative routes
Entering a special destination with
search area with assistance from
the system
Categories for entering special des­
tinations
Search areas for entering special
destinations
Entering an online destination*
Correcting an entry
Closing the full List of commands
Say:
Last destinations
Navigation favourites
Home address or Drive home
Enter address > follow the directions given by the system
Enter country / Enter town / Enter post code / Enter street /
Enter house number
Correction
Drive me to (XY) or Navigate to (XY), e.g. Drive me to John
Smith
Navigate to (XY) business / private,

e.g.
"Navigate to John Smith private"
Navigation favourites > Line (XY) / line content
>
start route
guidance when requested
Navigate / Navigate to private address / Navigate to business
address
Enter address
>
desired address when requested
>
confirm new
destination/stopover when requested
Start route guidance
Stop route guidance
Calculate alternative routes
Special destination > Change search area > enter desired cate­
gory or subcategory when requested, e.g. "Restaurant"
Audi Service / Railway station / Airport / Hotel / Hospital /
Parking space / Service area / Restaurant / Filling station etc.
In immediate vicinity / In vicinity of route / In vicinity of desti­
nation / In vicinity of stopover / In new town / In new country
Online destination (XY), e.g. "Online destination Palace Hotel"

No,
I meant (XY)
Close
Important: The Navigation or Map menu must
be open. You can say the following commands to
make additional navigation settings: •
168

Navigation
Setting a destination from the map (via
MMI touch)

Applies
to: vehicles with navigation system (flash memory)

and
MMI touch pad
A location on the map can be set as a destina­
tion.
- To set a convenient map scale: Turn the rotary
pushbutton clockwise or anti-clockwise.
- To activate the crosshairs: Press the rotary
pushbutton. The crosshairs will appear on the

map.

- To move the crosshairs: Use the MMI touch pad
to move the crosshairs to the destination

<^>page
156.
- To use the destination for route guidance:
Press the rotary pushbutton when the cross­
hairs are displayed. If
you
wish to set
a
stop­

over, select and confirm Set as stopover and
then Start route guidance.
-
To
hide the crosshairs: Press the
|BACK|
button.
Additional information on the point selected
with the crosshairs: If
you
use the crosshairs to
preselect a location on the map, any existing in­
formation on this location (e.g. road name, ad­
dress or special destinations) will be displayed ©

^>page
219, Fig. 182.
Using home address/favourite as the
destination

Applies
to: vehicles with navigation system

The
home address option is a quick and easy way
to have the system guide you home.
The
favour­

ites make it easier to
access
destinations you re­
quire regularly.
• Press the
|NAV/MAP|
button repeatedly until
the Enter destination menu is displayed

opage
207, Fig. 172.
Using the home address as the destination
Important: A home address must have been stor­
ed
o
page 215.
Your home address is displayed in the Enter des­
tination menu
(f) opage
207, Fig. 172.
- SeLect: Home address
>
Start route guidance.
Using a favourite as the destination
Important: At Least one favourite must have been
stored as a destination
<=>page
216.
- Enter at least the first three letters of the de­
sired favourite in the entry field for the search

function.
The favourites found will be shown on
the infotainment display (4)
^>page
207,
Fig. 172.
- SeLect and confirm the desired item.
- Select and confirm Start route guidance.
- Further home address settings can be found
on
•=>page
215.
- Further favourites settings can be found on

^>page
216.
Using a destination from the directory

Applies
to: vehicles with navigation system

You
can navigate directly to entries in the direc­

tory.

Options — Show contact details
H
^

i
i

C

Fiç

s
Max
Mustermann jy
.
E^
MusterstraGe
4,
54321 Musterstadt [

jr3^^
HauptstraSe
1,
54321
Musterstadt

h ^\
(D) 54321 Musterstadt,
MusterstraBe
^J
0°45'44.5"N,
l°25'30.7'O
•
•=

. 174 Possible directory contacts
Important: A postal address with navigation data
must be available for
a
contact or
a
navigation
destination must have already been added for a
contact
Opage
216, Directory contacts.

•
Press the
|NAV/MAP|
button repeatedly until
the Enter destination menu is displayed

^>page
207, Fig. 172.

*•
Select: left control button > Directory
>
a con­

tact.

Directory contacts are displayed in alphabetical
order and are displayed together with a location

symbol:

(Î)
Business postal address
(D Private postal address
210

Navigation
(D Business navigation destination
(4) Private navigation destination
- SeLect and confirm a postal address or
a
naviga­
tion destination. If
you
select
a
navigation des­

tination,
route guidance is started immediate-

iy.

- If
you
select a postal address, you can check the
address details again.
- You can then select and confirm Start route
guidance.
Further directory functions in the navigation sys­
tem can be found on
<^>page
216.
- Addresses which you have imported from
your mobiLe phone into the MMI can also be
used as navigation destinations.
- If
a
directory contact is greyed out, no
navi­

gation destination/postal address has yet
been added for the contact.
Point of interest search (special
destinations)

Applies
to: vehicles with navigation system
Navigation: enter destination
Search area
Find entry
Select category
Ç myAudi special destinations

H
Petrol station
P parking facilities
in vicinity of destination

Fig.
175 Example: Searching for a special destination

•
Press the |NAV/MAP| button repeatedly until
the Enter destination menu is displayed

•=>
page 207, Fig. 172.

*-
Select: left control button > Special destina­

tions.

- To change the search area: Select and confirm
Search area and then a search area from the
list.
The following search categories are available:
In immediate vicinity: You can select special des­
tinations from different categories. The special
destinations are displayed in a list, starting with
destinations in the immediate vicinity and going
up to destinations within a radius of 200 km.
In vicinity of route: Special destinations along
the route can only be selected when the route
guidance function is active. The special destina­
tions are located directly on or in the immediate
vicinity of your route. You can also select special
destinations from different categories. For exam­

ple,
you can look for
a
hotel or
a
car park at the
destination.
In vicinity of destination/In vicinity of stopover:
Special destinations near the
destination/stop­

over can only be selected when the route
guid­

ance function is active. You can also select special
destinations from different categories. For exam­

ple,
you can look for
a
hotel or
a
car park at the
destination.
In new town: SeLect
a
country or search in a new

town.
Enter the name of the desired town. You
can select special destinations from different cat­
egories. You can use this function to find special
destinations in any town irrespective of the desti­
nation currently set or the vehicle position.
- To find the name of
a
special destination in
the selected search area: Enter the name of the
special destination.
- To search for a special destination in a specific
category: Choose Select category. SeLect and
confirm a category, for example Restaurant.
myAudi special
destinations*1525

In myAudi special destinations, you can find per­
sonal special destinations which you have added
in your myAudi account and imported to the MMI
using an SD card or online*
^>page
224.
- To add further myAudi special destinations:
Select the right control button > Import •

CO

<
O
rN
IN
rN
t-H
o

<

^
Important: You must have created a myAudi account at

my.audi.com,
added a vehicle to the account and stored a

destination.

2)
This function is not available in the Mexican market.
211