warning AUDI Q3 2017 Owner´s Manual

a:,
A WARNING
-Never close the windows or panorama g lass
roof carelessly or in an uncontrolled man­
ner, because this increases the risk of injury.
- For security reasons, the windows and the
panorama glass roof can only be opened
and closed w ith the remote control key at a
maximum distance of approximate ly 2 m
away from the vehicle. Always pay attention
when using the~ button to close the win­
dows and the panorama glass roof so that
no one is pinched. The closing process will
stop immediate ly when the~ button is re­
leased .
Correcting power window malfunctions
You can reactivate the one-touch up/down func­
tion if it malfunctions.
"Pull the power window sw itch up until the win ­
dow is completely ra ised .
" Release the switch and pull it up again for at
least one second.
" Press the power window switch until the win­
dow is comp lete ly lowered.
" Release the switch and press it again for at
least one second. Now you can close the win­
dow as usual.
Panorama glass roof
Opening/closing the roof
App lies to : ve hicles wit h panorama g lass roof
Fig. 31 Front hea dliner : panor ama roof butto ns
lg
9 ::, co a,
~ @ Tilting the roof N
~ "To tilt the sunroof completely, press the~ 0
g button up br iefly to the second level. a:,
Opening and closing
"To close the sunroof completely, pull the~
button down briefly to the second level
c::> .&, .
.. To set a position between opened and closed,
press/pull the~ button up to the first level
until the desired position is reached.
® Sliding the roof
.. To open the sunroof completely, slide the but­
ton ~ toward the rear briefly to the second lev ­
el.
" To close the sunroof completely, slide the~
button forward briefly to the second level
c:;> .&,.
"To select a partia lly open pos ition, slide the~
button forward/back to the first level until the
desired posit ion is reached.
© Opening and closing the sun shade
"To completely open the sun shade, briefly press
the right button .
" To completely close the sun shade, br iefly press
the left button.
" To stop the sun shade , press the corresponding
button again.
You can st ill operate the panorama glass roof for
about 10 minutes after the ignit ion is switched
off. The switch is deactivated once the driver's or
front passenger's door is opened.
& WARNING
Be careful when closing the panoramic sun­
roof -otherwise serious inju ry could result!
For this reason, always remove the ignition
key when leaving the vehicle.
(D Note
-
Always close the panorama g lass roof when
l eav ing yo ur vehicle. Rain can cause damage
to the interior equipment of your veh icle, par­
ticularly the electronic equ ipment.
(D Tips
- For information about convenience open­
ing/closing, refer to
c:> page 32.
- The panorama roof will only open down to
-4°F (-20°).
33

a:,
a:,
...... N r--. N
'"' 0 0 ::, a:,
Lights and Vision
Exterior Lighting
Switching lights on and off
Fig. 32 Instrument panel: l ig ht switc h
Light switch ·'!;5- ·
Turn the switch to the corresponding position.
When the lights are sw itched on, the
;oo: symbol
turns on.
0 -lights off. On some market-specific vers ions,
the daytime running lights* will switch on when
the ign ition is switched on in this position .
-USA model s: the daytime running lights sw itch
on automatically when the ignition is switched
on and the light switch is in the
O position or in
the
AUTO position (on ly in daylight) . The Day ­
tim e running lights
can be switched on and off
in the radio or the MMI*
c:> page 36, c:> A.
-Canada models: the dayt ime running lights
switch on automatically when the ignition is
switched on and the light switch is set to the
0
pos ition, ;oo: o r the AUTO position (o nly in day­
li gh t)
c::> A .
AUTO* -automatic headlig hts switch o n and off
dependi ng on br ightness, fo r example in tw ilight,
d ur ing ra in or in tunne ls .
::oo: -Parking lights
io -Low beam headlights
~- All weat he r ligh ts. T urn the swi tch to pa rking
light
; oo : or low beam head light io . Pull the
sw itch up to the first notch@.
@il -Rea r fog lig hts . T urn the sw itch to par king
l ight
;oo; o r low beam head lig ht gD. Pull the
sw itch up to the secon d no tch @.
Lights and V ision
All-weather lights
T he fro nt lights a re adju sted au to mat ic a lly so
t h at there is less g lare for the driver from his o r
her own lights, fo r example whe n roads a re wet.
Automatic dynamic headlight range control
system
Your vehicle is equip ped with a headlight r ange
contro l system so that there is less g lare for on­
coming traff ic if the vehicle load changes . The
headlight range also adjusts automatically when
braking a nd accelerat ing .
Static cornering light*
The s tat ic co rnering light may be available de­
pending on vehicle equipment and it only works
whe n the light switc h is in t he AUTO position. The
corner ing light sw itches on automat ically at
speeds up to approximately 44 mph (70 km)
whe n the steeri ng wheel is at a certain angle. The
area to the side of the veh icle is illuminated be t­
te r when tur ning .
A WARNING
-Automatic headlights * are on ly inten ded to
assis t the driver. They do n ot relieve the
d river o f respons ibility to check the head ­
lights and to turn them on manua lly based
on the current light and vis ibility conditions.
For examp le, fog cannot be detected by the
light sensors . So always switch on the low
beam under these weat her condit ions an d
when dr iv ing in the da rk
gD .
-The rear fog lights shou ld only be turned on
in acco rdance w it h traffic regulations, to
p revent glare for traffic behind your vehicle.
- Always observe legal regulations when us­
i n g the lighting systems desc ribed.
(D Tips
- The light sensor for the automat ic head­
lights * is in the rearview mir ror mount. Do
not p lace any st ickers in this a rea on t he
w indshield.
- Some exter io r light ing funct ions can be ad­
justed
c:> page 36.
35

Lights and Vision
-If you turn off the ignition whi le the exter ior
lights are on and open the door, a warning
tone sounds.
- In cool o r damp weather, the inside of the
headlights, turn s ignals and tail lights can
fog over due to the temperature d if f erence
between the inside and outside. They will
clear short ly after switch ing them on. This
does not affect the serv ice life of the light­
i ng .
Turn signal and high beam lever
The turn signal lever operates the turn signals,
the high beams and the headlight flasher .
Fig. 33 Turn signal and high beam lever
Tu rn signals ¢ 9
The turn s ignals activate when you move the lev­
er into a turn s ignal position w hen the ign ition is
sw itched on.
@ -righ t turn signal
@ -left turn s ignal
The turn signal blinks three times if you just tap
the lever.
High b eams and headl ight flasher ~D
Move the lever to the co rrespo nd ing pos it ion .
@ -high beams on
© -high beams off or headlight flasher
The
II indicator light in the instrument cluster
turns on .
A WARNING
High beams can cause glare fo r other drivers,
w hi ch increases the risk of an accident. For
36
this reason, only use the high beams or the
headlight flasher when they will not create
glare for other dr ivers.
Adjusting the exterior lighting
The functions are adjusted in the Infotainment
system .
.,.. Sele ct: !CAR ! function b utton> (Car ) Systems *
control button > Vehicle settings > Exte rior
lighti ng.
Coming home, Leaving home*
The coming home fun ction ill umin ates the a rea
outside the vehicle when you tu rn the ignit io n off
and open the driver's doo r. To turn the func tion
on, select
Light s when leaving car > On .
The leaving home illum ina tes the area ou tside
the ve hicle when yo u un lo ck the vehicle . To turn
the function on, se lect
Lights when unlocking >
On .
The coming home and leav ing home func tions
on ly opera te when it is dar k and the l ight switc h
i s in the
AUTO position.
Daytime running lights*
USA models :
the daytime running lights can be
swit ched on/off. Sele ct
On or Off .
Canada models:
this function cannot be sw itched
off . They activate automatically each time the ig­
nit ion is switched on .
Emergency flashers
Fig. 3 4 Center conso le: emerge ncy flasher button
The emergency flashers makes other drivers
aware of your veh icle in dange rous situations.
In N 0
~ Cl) m

Lights and Vision
and the ignition is switched on . The illum ina ­
tion reduces automatica lly and eventually
turns
off as brightness outs ide decreases.
This function reminds the driver to turn the
low beams on at the appropriate time .
Vision
Adjusting the exterior mirrors
Fig . 38 D river's doo r: kn ob fo r th e ex te ri or m irrors
T u rn the knob to the desired pos ition:
Q/P -Adjus ting the left/ righ t exterior m irror .
Move the knob in the desired dire ction .
®l-Heating * th e mirror glass d epending on the
outs ide temperature .
8 -Folding exterior mirrors*.
Front passenger's exterior mirror tilt
function*
To he lp you see the curb w hen ba cking into a
parking space, the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger 's outs ide
mir ror .
You can adjust the tilted mirror surface by turn ­
ing the knob in the desired direction. When you
move out of r everse and into another g ear, the
new mirror position is stored and assigned to the
key you are us ing .
The mirror goes back into its origina l position
once yo u drive forward faster than 9 mph
( 1 5 km/h) or turn the ignition
off.
38
A WARNING
Curved mirror surfaces (for example convex)
e nla rge the field of vision. However, they
make ob jects in the mirro r appear smaller
a nd farther away . Your may est imate inco r­
rect ly w hen you use these mirro rs to gauge
your dista nce from the veh icles beh ind you
when chang ing lanes , whi ch in cr eases the risk
of an acc ident .
(D Note
-If the m irror housing w as moved by outside
f o rces ( such as a n impac t when maneuve r­
ing), yo u m ust use the power folding fu nc­
tion to fo ld the mirror all the way out. The
mi rror housing must not be moved back in­
to place by hand because t his wou ld impair
the funct ion of the mirror mechanism .
- If you wash the vehicle in an automatic ca r
wash, you must fold the exter ior mirrors in
to reduce the r isk of damage to the m irrors.
Never fold power fo ld ing exterior mirrors*
by hand . Only fold them in and out using
the power con trols.
(D Tips
If the power ad justing function ma lfunctions,
the glass in both m irrors can be adjusted by
pressing on the edge of it by hand .
Dimming the mirrors
Your vehicle is equipped with a manual or auto ­
matic dimming rearview mirror .
Fig. 39 A uto mat ic dimmin g rearview m irro r*
Manual dimming rearview mirror*
....
0 0
> ~ m
"" Pull the lever on the bot tom of the m irro r b ack . Ill-

Automatic dimming rearview mirror*
• Press the button @to switch the dimming
function on the mirror on or off. If the indicator
light @ turns on, the interior and exterior mir­
rors* are dimmed when light shines on them
(for example headlights shining from a vehicle
behind you) .
A WARNING
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out . This liquid
can irritate the skin, eyes and respiratory sys­
tem. If there is contact with the fluid, flush
immediately with plenty of water. Consult a
physician if necessary.
- Repeated or long-term exposure to electro­
lyte fluid can lead to irritation of the air­
ways, especially in people with asthma or
other respiratory conditions. Take deep
breaths immediately after leaving the vehi­
cle or, if this is not possible, open all of the
doors and windows as wide as possible.
- If electrolyte fluid enters the eyes, flush
them thoroughly with a large amount of
clean water for at least 15 minutes and then
seek medical attention.
- If electrolyte fluid comes into contact with
the skin, flush the affected area with clean
water for at least 15 minutes and then clean
with soap and water and seek medical at­
tention. Clean affected clothing and shoes
thoroughly before wear ing again .
- If the fluid was swallowed and the person is
conscious, flush the mouth with water for at
least 15 minutes. Do not induce vomiting
unless this is recommended by medical pro­
fessionals. Seek medical attention immedi­
ately.
(D Note
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
damages plastic surfaces and paint. Clean
this liquid as quickly as possible, for example
a:,
~ with a wet sponge.
N r--. N .... 0 0 ::, a:,
Lights and Vision
(D Tips
-If the light reaching the rearview mirror is
obstructed, the automatic dimming mirror
will not function correctly,
- The automatic dimming mirrors do not dim
when the interior lighting is turned on or
the reverse gear is selected.
Sun visors
Fig. 40 Driver 's s ide: sun viso r
The sun visors for the driver and front passenger
can be released from their mounts and turned to­
ward the doors
(D . The sun visors can also be
moved* back and forth lengthwise in this posi­
tion.
The mirror lighting* switches on when the cover over the vanity mirror @opens.
39

Lights and Vision
Windshield wipers
Switching the windshield w ipers on
F ig. 4 1 Wind shield wiper le ver
F ig. 42 Act uate t he re ar windo w wipe r
Move the windshield wiper lever to the corre­
spond ing pos ition:
@ -wipers off
(D -interval mode. To i ncrease/decrease the wip ­
er intervals, move the switch @ to the left/right.
In vehicles with a ra in sensor *, the wipers turn on
in the rain once the vehicle speed exceeds ap­
proximate ly 2 mph (4 km/h) . The higher the rain
sensor sensitivity is set (switch @to the right),
the earlier the windshield wipers react to mois ­
ture on the windsh ield .
@-slow wiping
@-fast w iping
© -sing le w ipe If yo u hold the leve r in th is posi­
tion longer, t he wipers sw itch from s low w iping
to fast wiping.
® -clean the windsh ie ld The wipe rs wipe one
time afte r several seconds of dr iv ing to remove
water drop lets . You can swi tch this func tion off
by moving the lever to position ® within 10 sec­
onds of the afterwipe . The afterwipe function is
40
reactivated the next time you switch the ignit ion
on .
®-wipe the rea r window. The rear wiper moves
about every 6 seco nds.
0 -clean the rea r window . The number of wipes
depends on how long the lever is held in pos it ion
(i) .
& WARNING
-The rain sensor is on ly intended to ass is t th e
driver . The driver may still be responsible
for manually switch ing the wipers on based
on visibility conditions .
- Th e windsh ield may not be treated with wa­
ter-repelling windshield coating agents . Un­
favorable conditions, such as wetness, dark­
ness, and when the sun is low, can ca use i n­
creased glare, wh ich increases the r isk of an
accident . Wiper blade chatter is also possi­
b le .
- Properly functioning windshield wipe r
blades are required for a clear v iew and safe
driving
~ page 41, Replacing front wind­
shield wiper blades.
(D Note
- If there is frost, make sure the windshield
w iper blades are no t frozen to the wind­
shield . Switch ing on the w indshield w ipers
when the blades are frozen to the win d­
shield can dam age the w iper blades.
- Pr ior to using a car was h, the w indshie ld
w iper sys tem mus t be sw itche d off (lever in
posit ion @). This preven ts the w ipers from
switching on unin tentionally and causi ng
damage to the windsh ield wiper system .
(D Tips
- The windshie ld wipers switch off w hen the
ignition is switc hed off . You can activate t he
windshield wipe rs after the ignition is
switched back on by moving the w indshield
wiper lever to any position .
- Wor n or dirty w indshield w iper blades resu lt
in streaking. Th is can affect the rain senso r*
function. Check your w indshield wiper
blades reg ularly. .,.

00
00
......
"' ,....
"' ...... 0 0 :::,
00
- The washer fluid nozzles for the windshie ld
washer system are heated at low tempera­
tures when the ignition is on.
- When stopping temporarily, such as at a
traffic light, the speed of the windshie ld
wipers automatically reduces by one level.
Cleaning windshield wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner .
Windshield wiper
.. Place the windshield wiper arms in the service
pos it ion ¢
page 41.
"' Fold the w indshield wiper arm away from the
windshield .
Rear window wiper
.. Fold the wiper arm away from the rear window .
.&_ WARNING
Dirty windshield wiper blades can impair vi­
sion, which increases the risk of an accident.
Replacing front windshield wiper blades
F ig . 43 Re mov ing w inds hield w iper blades
Windshield wiper service position/blade
replacement position
.. Switch the windshield wipers off (position @
¢ page 40, fig. 41).
-
"'Switch off the ignition and hold the windshield
wiper lever in position @¢
page 40, fig. 41 un­
t il the windsh ield wiper moves into the service
pos ition .
Lights and Vision
"'To bring the wiper b lades back into the original
position, switch the ignition on and operate the
w indshield w iper lever .
Removing the wiper blade
"' Fold the windshie ld wiper arm away from the
windshield .
.. Press the locking knob
(D ~ fig. 43 on the wiper
blade . Hold the wiper blade firmly.
.. Remove the w iper blade in the direction of the
arrow.
Installing the wiper blade
"'I nsert the new wiper blade into the mount on
the wiper arm @until it clicks into place.
.. Place the wiper arm back on the window.
"' To bring the wiper b lades back into the original
position, switch the ignition on and operate the
windshield wiper lever.
.&_ WARNING
-
For safety reasons, the windshield wiper
blades should be replaced once or twice each
year .
([) Note
-The windshield wiper blades must only be
replaced when in the service pos ition! Oth­
erwise, you ris k damaging the paint on the
hood or the windshield wiper motor.
- You should not move your vehicle or press
the windsh ield wiper leve r when the wiper
arms are folded away from the windshie ld.
T he windshie ld wipers wou ld move back in­
to their original position and could damage
the hood and windshie ld.
- To help prevent damage to the wiper sys­
tem, always loosen blades which are frozen
to the windshield before operating wipers.
- To help prevent damage to wiper blades, do
not use gasoline, kerosene, paint thinner, or
other so lvents on or near the wiper blades.
- To help prevent damage to the wiper arms
or other components, do not attempt to
move the wipers by hand.
41

Lights and Vision
@ Tips
-You can also use the service position, for ex­
ample, if you want to protect the windsh ield
from icing by using a cover.
- You cannot activate the service position
when the hood is open.
Replacing rear wiper blades
Fig . 44 Rear window wiper: removing the wiper blade
Removing th e wiper blade
16 M 0 ci: (X) a,
• Fo ld the w iper arm away from the rear window.
• Pull the wiper blade and holder out of the
mount.
Installing th e wiper blade
• Press the wiper b lade retainer in the direction
of the ar row into the mount.
• Fo ld the window wiper arm back onto the rear
window.
A WARNING
For safety reasons, the windshie ld wiper
blades should be replaced once or tw ice each
year.
42
Digital compass
Switching the compass on and off
App lies to: vehicles with digital compass
Fig. 45 Rearv iew m ir ror : d ig ita l compass is sw itched on
• To turn the compass in the mirror on or off,
press the butto n@ unt il the compass display
in the mir ror appears or d isappears.
0 N
I .,
The digital compass on ly works when the ignit ion
i s turned on. The directions are indicated with ab­
brev iat ions:
N (north), NE (northeast), E (east),
S E (southeast), S (south), SW (southwest), W
(wes t), NW (no rthwest).
(D Tips
To preve nt inaccurate compass read ings, do
n ot br ing any remote cont ro ls, elect rical dev i­
ces or metallic objects near the mirror.

a:,
a:,
...... N r--. N
'"' 0 0 ::, a:,
Adjusting the magnetic zone
Applies to: vehicles with digital compass
The magnetic zone must be adjusted correctly
for the compass to read accurately .
®
Fig. 46 Nort h Americ a: magn etic zone map
• Press and hold the button @i=> fig. 46 unt il the
number of the selected magnetic zone appears
in the rearv iew mirror.
• Press the button @repeatedly to select the
correct magnetic field zone . T he select io n
mode t urns off after a few seconds.
Calibrating the compass
Applies to: vehicles with digital compass
You must recalibrate the compass if it does not
display the correct direction .
• Press and hold the button @i=> page 42, fig . 45
unt il a C appears in the interior rearview mirror .
• Drive in a c ircle at about 6 mph ( 10 km/h) unt il
a d irection is disp layed in the rea rview mirror.
_& WARNING ,___
- T o reduce the risk to you rself and other driv­
ers, calibrate the compass i n an area where
there is no traffic.
Lights and V ision
-Always pay attention to the traffic and the
area around your vehicle if you are read ing
the compass while dr iv ing .
43

Sea ts and stor age
Seats and storage
General information
A WARNING
See c::> page 100, Driving safety for important
information, tips, suggestions and warnings
that you should read and follow for your own
safety and the safety of yo ur passengers .
Front seats
Manual seat adjustment
Appl ies to vehicles with manual adiustable seats
Fig. 4 7 Front seat: manual seat ad justment
@ -Moving the seat fo rwa rd/back: pull the lever
and slide the seat.
@ -Lengthen ing/shortening the upper thigh
support*: lift the hand le.
@ -Adjusting the angle of the seat surface*.
Pull/press t he lever.
© -Adjusting the lumbar support*: press the
button in the desired direction .
®-Moving the seat up/down: pull/press the lev­
er.
@ -Adjusting the backrest angle : turn the ad­
justing wheel.
WARNING
- Only adjust the front seat with when the ve­
hicle is stationary . Otherwise, this increases
the risk of an accident
- Exercise caution when adjusting the seat
height. Adjusting the seat care lessly or
44
w ithout checking can p inch hands and fin­
gers.
- The front seat backrests must not be re­
clined too far back when driving, because
this impa irs the effectiveness of the safety
be lts and airbag system, which increases
the risk of inj ury .
Power seat adjustment
App lies to vehicles w it h power adjustab le seats
Fig . 48 Front seat: power seat adjustment
@ -Adjust ing the lumbar support : press the but­
ton in the applicable position.
®-moving the seat up/down: press the button
up/down. To adjust the front seat cushion, press
the front button up/down. To adjust the rear seat
cushion, press the rear button up/down.
®-moving the seat forward/back : press the
button forward/back.
© -adjust ing the backrest ang le: press the bu t­
ton forward/back .
@-Lengthening/shortening the upper th igh
support*: lift the handle.
A WARNING
- Onl y adjust the front seat with when the ve­
hicle is sta tionary . Otherwise, this inc reases
the risk of an accident
- The power adj ustmen t for the front se ats al­
so works wi th the ignit ion sw itched off or
with the ignition key removed . For this rea­
son, chi ldren should never be left unattend­
ed in the vehicle -they could be injured!