warning lights AUDI Q5 2013 User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 2013, Model line: Q5, Model: AUDI Q5 2013Pages: 316, PDF Size: 78.89 MB
Page 31 of 316

warning goes out after about 5 seconds, but it
can be brought up at any time by pressing the
ISETI button again.
Usu ally, you can still drive to the nex t dea ler
ship. Turn off all but the most necessary elec
trica l consumers, since these drain the vehi
cle's battery.
@ Note
If the . warning symbo l (coolant system
malfunction) also lights up on the instru
ment panel during the trip¢
page 30,
then you have to stop immediately and
turn off the eng ine. The coolant pump is
not working anymore -danger of damage
to the eng ine!
BRAKE/( (j)) Brake system malfunction
A malfunction in the brake system must be
repaired as soon as possible .
If the warn ing /indicator light ~ (USA
models)/ . (Canada mode ls) in the instru
ment cluster flashes, there is a brake system
malfunct ion . A dr iver message appears as
well to explain the malfunction in mo re de
tail. The d rive r warning goes out after about 5
seconds, b ut i t can be brought up at any time
by pressing the
I SE T! button aga in .
Stop vehicle and check brake fluid l evel
~ Stop the vehicle.
~ Check the brak e fluid leve l¢ page 242.
~ Seek professiona l assistance if necessa ry.
Warning! Fault in brake system. Contact
workshop
~ Drive carefu lly to the nearest authorized
Audi dealer or other qualified workshop and
have the malfunct ion correc ted ¢
&-
Par king brake system fault! See owner's
manual
~ If t his symbol appears when t he ve hicle is
stationary or afte r the ign ition is turned on,
chec k to see if the parking bra ke can be re
l eased. Drive to an authorized Audi dealer or
other qualified workshop as soon as possi-
Dri ver information di spla y 29
ble and have the malfunction cor rected . If
the parki ng brake cannot be opened, then
take it to an expert at an authorized Audi
dea ler.
~ If the symbo l appears while you are driving,
it is possible that the traction co ntrol o r the
emerge ncy brake has malfunctioned .
It is
possible that th e parking b rake cannot be
app lied.
It is also possible t hat the parking
b ra ke cannot be re le ased after i t has been
app lied . D rive to an authorized Aud i dea ler
or ot her qualified workshop to have t he mal
function corrected.
If t he ABS system malfu nctions, the ABS
warning/indicator light illumina tes together
with the brake system ma lfunction wa rning/
indicator light ¢.& .
A WARNING
-A lways observe the warn ings in
¢ page 226, Engine compartment, be
fore opening the hood and check ing the
bra ke fluid.
- Driving with low brake fluid is a safety
hazard . Stop the car a nd get professiona l
assistance .
-USA models: If th e ~ warning light
a nd the
B warning light come on to
gethe r, the rear whee ls cou ld lock up
fi rst under hard bra king. Rear wheel lock
up can ca use loss of vehicle co ntrol and
an ac cident. Have yo ur vehicle rep aire d
immediate ly by yo ur authorize d Au di
dea ler o r a qua lified wor kshop. Drive
slowly and avo id sudden, hard brake ap
plications.
- Canada models: If the brake warning
light . and the ABS warning light
El]
come on together, the rear wheels could
lock up first under hard braking. Rear
wheel lock-up can cause loss of vehicle
control and an acc ident. Have yo ur vehi
cle repaired immed iately by your author
i z ed A udi dealer o r a q ual ified wor kshop.
Drive s low ly and avoid s udden, hard
brake applications .
Page 32 of 316

30 Driver in formation d isplay
...L Engine cooling system malfunction
A malfunction in the engine cooling system
must be repaired as soon as possible .
If the . symbol flashes in the display, either
t he eng ine cool ant
temperature is too h igh or
the eng ine coolant
level is too low . A dr iver
message appears as well to explain the mal
function in more detail. The d rive r warning
goes out afte r about 5 seconds, but it ca n be
b rought up a t any time by p ress ing the
!SE TI
button again.
Turn off engine and ch eck coolant l evel
• Pull off the road .
• Stop the vehicle .
• Turn off the engine.
• Check coo lant level¢
page 240.
• Add coolant if ne cessa ry ¢ page 241 .
• Co ntin ue d riving only after the eng ine cool
ant warn ing/ indicato r light goes o ut.
• Contact your a uthorized Audi dea ler for as-
sistance if necessary.
If the engine coolant level is co rrec t, then the
radia tor fan may be the cause o f the malf unc
tion .
A WARNING
-If your veh icle should break down for
mechanical or other reasons, park at a
safe distance from moving traffic, turn off the engi ne and turn on the hazard
wa rning lights ¢
page 52, Emergency
flash ers.
-
- Never open the hood if you see or hea r
steam o r coolant esca ping from the en
gine compa rtme nt - you risk being s cald
ed. Wait until you can no longe r see or
hear steam or coo lant es caping.
- T he e ngine compartmen t of a ny veh icle
is a dan gerous area. Before you perform
any wor k in the engine compartment,
t ur n of the engine and allow it to coo l.
Follow the wa rning stickers ¢
page 226,
Engine compartment.
(D Note
Do not continue driv ing if the . symbo l
ill um inates . There is a mal function in the
engine cooling system -you could damage
your engine.
"l:::r. Engine oil pressure malfunction
T he red engine oil pressure warning symbol
requires immediate service or repair. Driving with a low
oil pressure indication is likely to
cause severe engine damage .
If the . symbo l on the disp lay flashes, the
engine oil pressure is too low. A driver mes
sage appears as we ll to exp la in the malfunc
t io n in more detail. The dr iver warning goes
o ut afte r abo ut 5 seconds , but it can be
brought up at any t ime by p ressing the
~ 1s =ET= I
button ag ain.
Turn off engin e! O il pressure too low
• Stop the vehicle.
• Turn the engine off.
• Chec k the engine o il level ¢
page 238 .
• Contact yo ur au thorized Aud i deale r for as-
sistance if necessa ry.
Eng ine oil level too low
If the engine oil level is too low, add engine
o il
¢page 238.
Engine oil leve l correct
If the symbol . flashes even tho ugh the en
gine oil leve l is correct, please contact your
nearest authori zed Aud i Dea ler for assistance.
Do not continue dr iving . Do not leave the en
gine running
idle, either .
(D Tips
- The engine oil pressure symbol. is
not an indicator for a low eng ine oil lev
e l. Do not rely on it. Instead, check the
oil level in your engine at regular inter
vals, preferably each time you refuel, and always before going on a long trip .
Page 33 of 316

-The yellow oil level warning indication
II requires oil refill or workshop serv
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil
level warning
11-By then, your engine
may already have suffered serious dam
age .
~ . Fill engine oil now
WARNING: Please add oil immediately
If the . symbol lights up, then the o il has to
be re plenished r ight now ~
page 238 .
~- Steering malfunction
If there is a malfunction in the electronic
steering column lock, the steering cannot b e
unloc ked .
If the . symbol i n the display blinks , th ere
i s a malfunction in the electronic steer ing col
u m n lock . A driver message a ppears as well to
e xplain t he malfu nction in m ore deta il. The
d river war ning goes ou t a fter abou t
5 se c
on ds, but it can be brough t up at an y time by
p ress ing t he
ISE TI but ton again.
Steering defective! Do not drive vehicle!
.,. Co ntact your nearest authorized Audi deal
er .
.,. Do
not tow yo ur vehicle .
A WARNING
Your vehicle must not b e towe d in th e
eve nt of a m alfu nction in the ele ctronic
s t eerin g colum n lo ck bec ause i t ca n not be
steered due to the l ocked steering . If it is
towed with the stee ring loc ked, t here is
the risk of an accident.
© -Ignition lock malfunction
A mal function in the ignition lock mus t be re
paired immediately .
If th e. symbol in the d isp lay blink s, there
i s a ma lfunc tion in the elec troni c ignition lo ck.
Driver information display 31
A dr iver message appea rs as we ll to ex plain
t h e malfunction i n mo re deta il. The dr iver
warning goes out after a bout 5 seconds, b ut it
can be b roug ht up at any time by pressing the
ISE TI b utt on again.
Ignition lock defective. Contact dealer!
.,. Do not tu rn th e e ngine o ff.
.,. Drive imme diate ly to an a uthor ized A udi
dea le r to have t he mal funct io n corrected .
If there is a mal fun ctio n in t he ele ct ro nic igni
tio n loc k, the igni tion can not b e turne d off.
Drive immediate ly to an au tho riz e d se rvice fa
c ili ty to have t he cause of t he malfunct ion cor
r ected .
On vehicle s wi th Conven ien ce key* , the eng ine
s h ould not b e swi tc h ed off usin g th e S tart/
Stop button because t he engine cannot be
started again afte r th e ignit io n has been
switc hed off.
· Yellow symbols
A yellow symbol me ans WA RNING .
Fig. 24 Display: Yellow wa rning symbo l
N ..,
I
Yellow symbo ls ind icate a prior ity 2 malfunc
tion -Wa rning!
When a yellow warn ing symbol appears,
one
warning to ne sounds . A d river message ap
p ears as well to exp lai n the ma lfu nction in
m ore d etail. T he d rive r war ning goes out aft er
abo ut 5 seconds, but it ca n be broug ht up a t
any ti me by press ing t he
ISE TI button again .
Check the function displayed as s oon as possi
ble. The yellow symbol will not go out again
u nti l th e re ason fo r the mal func tion has bee n
cor rected.
Page 34 of 316

32 Driver in formation d isplay
If several priority 2 malfunctions a re present,
the symbols appear in succession and remain
for about 2 seconds .
,1,ij
Electromechanical steering,
Dynamic steering*
¢ page 201
•
Worn brake pads
¢page 33
&1
Battery voltage
¢page34
;....
J:J
Defective light bulb
¢page33
II
Fog lights
¢page 33
.... -
II
Rear fog ligh ts
¢page33
•
Check engine oil leve l
¢page34
Ill
Engine oil sensor malfunc-
tion
¢page34
•
Engine temperature*
¢page229
II
Low fuel level
¢page33
•
Windshield washer flu id level
low
¢ page33
!I
Convenience key *
Key not
in vehicle
¢page32
m
Light/rain sensor defective
¢page33
II
Dynamic headlight range
control defective
¢page34
I!
Battery in remote control key
¢ page 37
-
rm
.,
-
Ill
m
B
m
[DJ
11NIB
6HVBRID
(D Tips
E
lectromechanical parking
bra ke
¢page 91
Engine speed limitation *
¢ page 34, ¢ page 99
Adaptive light defective *
¢page34
Ignition lock malfunction
¢ page34
Adaptive dampers *
¢page35
Windshield wiper defective
¢page35
Tire pressure monitoring sys
tem*
L oss of tire pressure
¢page267
Tire pressure monitor ing sys
tem*
System not avai lab le
¢ page 267
Automatic transmission mal-I
function
¢page 128 j
Hybr id dr ive *
¢page99
The speed warnings warn ing thresho ld 1
Ct] and warning thresho ld 2 [i] are also
yellow symbo ls in some models . The warn
i ng is always shown as a small symbo l in
the upper a rea of the display ¢
page 93.
.Je Key not in vehicle
Applies to veh icles: w ith Convenience key
!I Is the key in the vehicl e?
Th is rem inder appears along with the !I sym
bo l if the master key is removed from the ve
hicle with the eng ine runn ing. It is intended
to rem ind you (e.g . whe n ch ang ing dr ivers) .,.
Page 35 of 316

not to continue the journey without the mas
ter key.
If the master key is no longer in the vehicle,
you cannot sw itch off the ignition after stop
ping the engine and you a lso cannot start the
engine again . You also cannot lock the vehicle
from the outs ide.
~ o Light/rain sensor defective
ral A utom atic he adlight s/ autom atic wi pers
d efect ive
If the symbol illuminates, the light sensor has
fa iled. For safety reasons the low beams are
turned on permanently with the switch in
A U
TO . However, you can continue to turn the
lights on and off us ing the light switch . In the
case of a defect in the rain sensor, the w ind
sh ie ld wiper lever functions are st ill available .
H ave the light/rain sensor checked as soon as
possible by an autho rized Aud i dea ler.
(0) Worn brake pad s
[IJ Brake pad s!
If the warn ing l ight illum inates, immediately
contact your authorized A udi dealer or quali
fied workshop to have all brake pads inspect
ed . On USA models the warning light
[IJ
comes on together with the warning light
1111 . Both sets of brake pads on an axle
must always be replaced at the same time.
A WARNING
Dr iv ing with bad brakes can cause a coll i
sion and serious personal injury.
- If the warning light
[IJ and the warning
light
11111> w ith the message B rak e
pads!
comes on in the instr ument cluster
display, immediately contact your au
tho rized Aud i deale r or qualified work
shop to have a ll brake pads checked or
replaced if necessary.
1) - : USA mod els only
-
Dri ver information di spla y 33
~!}010 $ Defective light bulb warning
I -If the ind icator light tu rns on, a bulb has
failed . The message ind icates the location of
the bu lb.
II -If a front fog lamp has fa iled, the ind ica
tor light tu rns on to indica te the location on
the vehi cle.
ml -If a rear fog lamp has fa iled, the indica
tor light turns on to indicate the location on
the ve hicl e.
Veh icl e light s: Sys te m fault!
If the message appears, there is a malfunc
tion in the headlights or light sw itch.
Drive to your authorized A udi dealer immedi
ate ly to have the malfunction corrected.
A WARNING
- Light bulbs are pressurized and could ex
plode wh ile they are being changed caus
ing serious personal injury.
- Work with due care when handling the high-voltage section of gas discharge
(xenon) lights* . Failure to do so could re
sult in death or serious injury .
(D Tips
Have the bulb replaced or the connection
repaired by your authorized Audi Service
department .
o:> Windshield washer fluid level too
low
- Please re fill w asher fluid
If the symbol il lum inates, add w indshield
washer flu id to the washer system and also to
the headlight washe r system
c::> page 247.
Eli) Fuel supply too low
When the Ii'] symbo l ill uminates, this means
there a re abo ut 2.6 gallons (10 liters) o f fuel ..,.
Page 46 of 316

44 Opening and closing
Automatic rear lid/
trunk lid operation
App lies to vehicles: with automat ic rear l id/trunk lid oper ·
ation
The trunk lid con be opened and closed auto
matically.
Fig. 36 Driver's doo r: Unlock ing the rear lid
Fig. 37 Locking switch in the rear lid
Opening the luggage compartment lid
.,. Press the button c::5 on the master key for
at least one second, or
.,. Pull the release button
c::5 in the dr iver's
door ~
fig. 36, or
.,. Press the handle in the lu ggage compart·
ment lid~
page 43, fig . 35 .
Closing the luggage compartment lid
.,. Press the button in the luggage compart·
ment lid
~ fig . 3 7 . The lid will automat ica lly
close and lock ¢.&, .
Setting the luggage compartment lid
open position
.,. Bring the luggage compartment lid into the
desired open position. The position can be
stored at only one specific height.
.,. Press and hold the
¢fig. 37 button for at
least four seconds until the lights blink to
store the desired open position. .,.
Push the luggage compartment lid by hand
against the resistance if you want to set a
higher open posit ion .
.,. Press and hold the¢
fig. 37 button again
for at least four seconds and this will store
the new open position .
Opening will be stopped immediately when:
- You press the
c::5 button on the remote key
for at least of one second, or
- press the unlock button
c::5 in the dr iver
door, or
- press the lock button the in the luggage
compartment lid, or
- push the handle in the luggage compart
ment lid, or
- when something blocks the rear lid or
makes it d ifficul t for the lid to move.
By pressing one of the button
c::5 repeatedly ,
you can stop or continue the opening process .
The pressing the lock button or the handle re·
peatedly, you can open/stop the lid ¢
,&..
Opening will be stopped immediately when:
- press the lock button the in the luggage
compartment lid, or
- push the handle in the luggage compart·
ment lid, or
- when something blocks the rear lid or
makes it difficult for the lid to move .
Th e pressing the lock button or the handle re ·
peatedly, you can open/stop the lid ¢
& .
You can manua lly stop the automatic open
ing/closing of the luggage compartment lid.
In this situation, the lid can be manually
opened. Press down on the lid and the auto
matic closing will resume once again.
A WARNING
-- Never close the rear lid inattentively or
without checking first . Al though the
clos ing force of the rear lid is limited,
you can still seriously injure yourself or
others .
.
Page 48 of 316

46 Opening and clo sing
Child safety locks
Child safety locks in the rear doors
The child safety locks t prevent the rear
doors from opening from the inside .
Fig. 39 Child safety locks on th e rear doors
I ti:: 00 (0
The rear doors are equipped with c hild safety
l ocks . The lock is only v is ible when the door is
open . Take the mechan ica l key out of the mas
ter key ¢
page 3 7.
Switching the child safety locks on
.,. Turn the key in the direction of the ar row
Qfig. 39.
Switching the child safet y locks off
.. Turn the key in the opposite d irection of the
arrow .
When the child safety locks are activated, the
inside door handles do not work and the doors
can only be opened from the outside .
Power windows
Controls
The driver can control all power windows.
Fig . 40 Sect io n of the driver's door: Controls
All power window switches are provided with
a two-position fun ction :
Opening the windows
.. Press t he switch to the first stop and ho ld it
until the window re aches the desired posi
tion.
.. Press the switch briefly to the
second stop
to automatically open the window .
Closing the windows
.. Pull the switch to the first stop and hold it
until the window reaches the desired posi
tion .
.. Pull the switch briefly to the
se cond stop to
automatically close the window .
Power window switches
@ Driver's door
® Passenger's door
© Left rear door
@ Right rear door
® Safety button
Child safety locks
When the safety button® Q fig. 40 is p ress
ed, the@symbol in the button lights up. The
power window switches in the rear doors are
switched off.
A WARNING
-
-When you leave your vehicle -even if on-
ly br iefly -always remove the ignition
key . T his app lies pa rticularly when chil
dren remain i n the vehicle . Othe rwis e the
children could start the eng ine or ope r
a te electrical eq uipment (e.g. power win
dows) . The power w indows are func tion
al un til the dr iver's door or passenge r's
door has been opened .
- Pay close attention when closing the win
dows to p revent pinching of hands or
lim bs.
- When locking the vehicle from outside,
the vehicle must be unoccupied since the
windows can no longer be opened in an
emergency.
Page 51 of 316

Clear vision Lights
Switching the lights on and off
F ig . 43 Instrument pane l: light sw itch
Sw itching on AUTO - Automatic headlight
contr ols
• Turn the light switch to AUTO ¢ fig. 43.
S w itchin g on the side m arker light s
• Turn the light switch to :oo~.
Switching on low beams
• Turn the light switch to @-0.
Swi tchin g off the light s
• Turn the light switch to 0.
The low beams only i lluminate with the igni
tion turned on.
With the s ide marker lights or headlights
switched on, the symbol next to the light
switch illuminates
:oo:.
AUTO -Automatic headlight control
With the switch in the AUTO position, the low
beams are swi tched on a utomatica lly depend
ing on the ambient light, for example in a tun
ne l, at dusk and when it is raining or snowing.
When the low beams are switched on, the
:oo:
symbol comes on. The low beams remain
switched on regardless of the ambient light
when you turn on the fog lights.
When you turn
off the ign ition, the low beams
are automatically switched
off.
W ith automatic headlight control, you also
have the high-beam function avai lab le . How -
Clear vi sion 49
ever, if you have not switched h igh beams
back to low beams while driving with auto
matic headlight control, only the low beams
come on the next time you turn on automatic
headlight control. In order to return to high
beams aga in, you first have to pull the high
beam lever back to the normal position and
then push the lever forward .
Light sen so r malfunct ion
In the event of a light sensor malfunction, the
driver is notified in the instrument cluster dis
play :
fal Automat ic headlight s/ automati c wipers
defec tive
For safety reasons, the low beams are turned
on permanently with the switch in
AUTO .
However, you can continue to turn the lights
on and
off using the light switch . Have the
light sensor checked as soon as possible at an
authorized Audi dealer or other qualified
workshop.
A WARNING
- Automatic headlights are only intended
to assist the driver. They do not relieve
the dr iver of his respons ibility to check
the head lights and to turn them on man
ually accord ing to the current lig ht and
visibility conditions. For example, fog cannot be detected by the light sensors.
So always sw itch on the headlights @-0
under these weather conditions and
when dr iving in the da rk .
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other moto rists. Always turn on
the head lights so that you can see ahead
and so that others can see your car from
the back.
- Please obey all laws when using the
lighting systems described here.
(l'} Tips
-The light sensor for head light control is
located in the rear
view mirror mount.
Yo u should therefore no t apply any
Page 55 of 316

Notes o n these featur es
-The turn signals only work with the ignition
turned on. The indicator lights
II or Ill in
the instrument cluster
¢page 14 also b link.
- After you have turned a corner, the turn sig-
nal switches off automatica lly.
- The
high beam works only when the head
lights are on. The indicator light
II in th e
instrument cluster illuminates when the
high beams are on.
- The
headlight flasher wo rks only as long as
you hold the lever -even if there are no
lights turned on. The indicator light
II in
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
Do not use the high beam or headlight
flasher if you know that thes e cou ld blind
oncoming traffic.
Interior lights
Front interior lights
-
The front interior lights also contain reading
lights for the driver and passenger .
r ,,,,, , 11111
~8 ,~
G) Gl
,o . . o
I
Fig. 49 Headliner: Fro nt inte rior/rea ding lights
The rocker switch @¢ fig. 49 for operating
the interior lighting has the following func
tions :
Door cont act swi tch
.,. Place the switch @ in the middle position.
Inte rior light switched on
.,. Place the switch@ in posit ion I.
Clear vision 5 3
Interior light switch ed off
.,. Place the sw itch @ in position 0.
Front re ad in g lights ~
.,. Press one of the switches@ to turn the
r ight or left reading light on or off .
With the door contact switch turned on, the
interior lights turn on as soon as you unlock
the vehicle or open the doors. The lighting is
also turned on when the ignition key is re
moved. The lights go out about 30 seconds af
ter the doors are closed. When the vehicle is locked or when the ignition is turned on, the
interior lights are turned off.
When a doo r is open, the interior lights are
tu rned off after about 10 minutes to prevent
draining of the battery .
The brightness of the lights is controlled au
tomat ica lly by a d immer when they are
swi tched on and off.
Rear interior lights
There are reading lights in the rear for the
passengers .
Fig . 50 Headliner: Rear read ing lig hts
The read ing l ights are switched on and off us
ing the buttons ~-
Depending on your model, the appearance
and the location of the reading lights may be
different .
Page 57 of 316

while driving. You can switch this function off by moving the lever to position ® within 10
seconds of the afterwipe operation. The after
wipe function is reactivated the next time the ignit ion is switched on.
The rear wiper automatically switches on
when the reverse gear is engaged and the
front w indshield wipers are on and in opera
tion .
C lea ning the headlights *. The headlight wash
er system * operates on ly when the headlights
are on. If you move the lever to pos ition ®,
the headlights are washed in interva ls .
® -Wipe the rear window. The rear wiper
moves about every 4 seconds .
0-Clean the rear window. The number of
wiping operations depends on how long the l ever is held in positio n 7.
A WARNING
-The ra in sensor is only intended to assist
the driver. The driver is still responsible
for man ually sw itching the w ipers on ac
cording to the v is ibility conditions.
- The windshie ld may not be treated w ith
water-repe lling windshie ld coat ing
agents. Unfavorable conditions, such as
wetness, darkness, low sun, can res ult in
increased glare. W iper b lade chatter is
also possible .
- Proper ly functioning w indshie ld w iper
blade s are required fo r a clear view and
sa fe dr iv ing .
(D Note
-In the case of frost, check whether the
windsh ield wiper b lades a re fro zen to
t h e windshie ld. Swit ching on the wind
s h ield wipers can d amage t he wipe r
blades!
- Prior to using a car w ash, the windshield
wipe r system m ust be swit ched off (lever
i n position 0) . This helps to prevent unin
tentiona l switching on and damage to
the windshie ld w iper system.
Clear v is ion 5 5
(D Tips
- The windshie ld w ipers are switched off
when the ign it ion is tu rned off . Act ivate
the windsh ield wipers after the ignition
is switc hed back on by moving t he wind
shield wipe r lever to any position .
- Worn or d irty windshield wiper blades
result in streaking. This ca n affect the
rai n sensor function. Check your wind
shield w iper blades regularly.
- The washer fluid nozz les of the wind
shield washe r system a re heated at low
tempe rat ures whe n the ignition is on .
- When stopping temporarily, e .g. at a
t raffic light, the set spe ed of the wind
shield wiper s is automatically reduced by
one speed.
Service position
The windshield wiper blades ore replaced in
the service position.
"' If the w iper blades are no t frozen to t he
w indshield, br ing the w indshie ld w iper lever
to the basic position @¢
page 54, fig . 53 .
"' Sele ct: !CAR !func tion butt on> Windshield
wipers
> Service position . Or
"' Sele ct: I CAR I func tion b utton > Car sy s
tem s*
contro l butto n > Servicing & checks >
Wiper service position . Or
"' Switch the ignit ion off and move the wind
shield w iper lever to position ©¢
page 54,
fig . 53.
- On -changing the windshield wiper b lades
can only be done if you b ring the wiper arms
to the service position . You will also avoid
pai nt damage to the hood when working on
the wipe rs in th is posit ion .
-Off -the w indshield w ipers are moved to
their in itia l position again .
(D Note
Neve r mane uver yo ur vehicle with t he
front windshie ld w iper arms raised s ince
they wi ll automatically be moved back to