warning light AUDI Q7 2011 Owner´s Manual

_________________________________________ I_ n_ t_ e_ ll_,igent technology ,__E~-
fore-and-aft and lateral directions, the brake pressure and the
steering angle are all measured.
The direction in which the driver wishes to travel is determined with
the aid of the steering angle and vehicle speed and is continually
compared with the actual behavior of the vehicle. If the two do not
match, for example, when the vehicle starts hydroplaning on a wet
road, ESP will automatically brake the appropriate whee l to correct
the problem.
The vehicle is then stabi lized by the forces acting on the whee l during
braking. If the vehicle is
oversteering (rear tends to skid out of the
turn), the brakes are main ly applied on the wheel that is on the
outs ide of the curve. In the case of a vehicle that is
understeering
(tendency to slide out of the curve), the brakes are applied as needed
on the wheel that is on the inside of the curve or additionally on the
other wheels. An acoustic s ignal indicates when ESP brake application
cuts in=> &.
The system operates across the entire speed range in combination
with the ABS system ~
page 260 . If the Anti -Lock Brake System
(ABS) ma lfunctions, the ESP wi ll be out of action as well.
Activating
When you turn on the engine, ESP will automatically be activated and
wi ll perform a self-test. As soon as the test is comp leted, the system
is in normal operating mode .
Offroad mode
ESP should normally be operated in normal mode because this
ensures maximum vehicle stability. If necessary, you can activate the
ESP offroad mode by pressing the button=>
page 256, fig. 222 to
obtain maximum traction and braking ability when driving off paved
roads at low speeds. In ESP offroad mode, the indicator light illu­
minates and the message
ESP Offroad Caution! Limited driving
stability
appears briefly in the d isp lay.
The ESP offroad mode can be useful in the following exceptiona l situ­
ations when slip or a highly effe ctive different ial loc king funct ion is
desirable. Examples:
Controls and equip­ ment Safety first Vehicle operation
•
when driving w ith tire chains,
• when driving in deep snow or on loose ground,
• when driving on uneven surfaces with the wheels severely
unloaded (articulation), and
• when rocking the vehicle loose a fter it has become stuck.
When the unusual situation is past, you should sh ift back to the
normal ESP operating mode by pushing the button again. The
message
ESP/ ASR on then appears briefly in the display.
Hill descent control
The hill descent control is switched on in ESP offroad mode. When
slowly descending steep gradients on loose ground or when the axles
are art iculated, hill descent control provides assistance by automati­
cally applying the brakes to keep vehicle speed constant. The vehicle
is also rende red easier to steer by select ive distribution of braking
force. Hill descent control intervenes when:
• the accelerator pedal is not pressed,
• the vehicle is travelling less than 12 mph (20 km/h),
• a steep gradient is detected,
• wheel behavior indicates loose ground or conditions with poor
adhesion (e.g. also axle articulat ion).
Hill descent control operates both dr iving forward and in reverse.
Active hi ll descent control is deactivated by pressing the accelerator
pedal until the conditions for activation already listed are met aga in.
& WARNING
• The Electronic Stabilization Program is nevertheless subject to
the laws of physics . It is particularly important to pay attention to
this fact on wet and slippery roads. It is therefore important that
you always adapt your driving to the condition of the road and
traffic conditions. Do not allow the increased safety provided by
the Electronic Stabilization Program system to lull you into
accepting additional safety risks. ..
Vehicle care Do-it-yourself service Technical data

Intelligent technology
'-----------------------------------------------
& WA RNING (conti nu ed )
• Plea se be aware th at in ESP offroad mode , particularly on a
s mooth and slippery road, the wheels may have an incr eased
tendency to spin and the vehicle may break awa y -danger of skid ­
ding!
• Stabilit y is limited in the ESP offroad mode. •
Electronic differential lock (EDL)
The electronic differential lock monitors the rotational
speed of the drive wheels.
General notes
The electronic differe ntia l lock (EDL) helps the ca r to sta rt moving,
acce lerate and climb a gradient on surfaces provi ding poor or almost
no grip. W ithout ED L, th is would be d iff ic ul t, if not impossible .
How the system works
The EDL operates automatically . It mo nitors the rotational speed of
w heels wi th the help of the ABS sensors ==>
page 260. If a not iceab le
slip is detected at the wheels (e .g . o n slippery g round on one side),
the spin ning whee ls are braked and power is transferred to the other
wheels. This is done up to a speed of about 60 mph ( 100 km/h) .
Noises from the brake system signa l that wheel spin is being
cont rolled.
Driv ing off
W hen d rivi ng off, always be sure to keep road conditions in mind as
you acce lerate. If one drive wheel spins because it is on a surface with
less grip, apply
plenty of th rottle until t he car starts to move .
Overheating of brakes
To prevent the disc b rake of the bra ked wheel from overhea ting if
subjected to excessive loads on this whee l, t he EDL cuts out tempo ­
ra rily. The vehicle rema ins operat iona l and behaves in the same way
as a veh icle without EDL. As soon as the brake has coo
led down, EDL sw itches on again auto­
m atically.
& WARNING
• When accelerating on slippery surfaces, such as on ice or snow,
always be careful when depressing the accele rator pedal. Even
with the EDL working , the drive wheels c an spin and reduce your
ability to control your car . Risk of crash!
• The increased safety afforded by EDL does not mean that you
can take safety risks . Always adapt your d riv ing style to the road
c ondition s and traffic situation.
[ i ] Tips
If a fa ult occurs in the A BS, the ED L is also no t fu nct io ni ng. This is
ind icated by the ABS warn ing light==>
page 19. •
Anti-Slip Regulation System (ASR)
The Anti- S lip Re gula tion System preven ts the drive n
w heels from spin ning wh en the car is acc ele rating .
General notes
The Anti-S lip Reg ulation Sys tem (ASR) is in tegr ated in the ele ctroni c
stabilization program (ESP) . When the ve hicle starts up and acceler­
a tes, the whee ls are p reven ted from sp inning by adjust ing t he engine
power to match the amoun t of grip ava ilable from the road surface.
How the system works
ASR performs automatica lly, i.e. witho ut the driver 's intervent ion.
With the aid o f th e ABS sensors ==>
page 260, ASR moni to rs the speed
of the driven wheels. If the whee ls start to spin, engine torque is
reduced automatically unt il the tires find enough gri p to lock onto
the road s urface. The system is active ac ross the en tire speed range .
'1>

_________________________________________ I_ n_ t_ e_ ll_,igent technology ,__E~-
If an individual wheel begins to rotate too slowly in relation to vehicle
speed and tends to lock, the ABS automatically reduces brake pres­
sure to prevent that wheel from locking .
Thi s automatic adjustment process wi ll cause a
slight vibration of
the brake pedal and some noises to alert you that vehicle speed must
be adapted to existing road and traffic conditions.
_& WARNING
Although the ABS is very effective, always remember that braking
capability is limited by tire traction. Always adjust your driving
speed according to the road and traffic conditions. Do not let the
extra safety afforded by the ABS tempt you into taking extra risks.
The ABS cannot overcome the laws of physics .
(I) Tips
• If ABS is not funct ioning properly, a warning light will come on .
See ~
page 19.
• If a fault occurs in the ABS, the EDL is also not functioning. This is
ind icat ed by the ABS warning light. •
Brake assistant
The brake assistant is designed to achieve the optimum
braking effect.
The brake assistant helps to increase the effective braking power and
thus to achieve a shorter stopping distance.
If the driver presses the
brake peda l very qu ickly , the brake assistant automatically boosts the
braking force to the maximum level, up to the point where the anti­
lock brake function (ABS) intervenes to stop the whee ls from locking.
You should then keep the brake pedal pressed until the vehicle has
braked to the required speed. The brake assistant switches itself off
as soon as you release the brake pedal.
Controls and equip­ ment Safety first Vehicle operation
Automatic full braking
assist
This function allows full braking in spite of high brake pedal forces
(e .g . when the brakes are severely stressed because the veh icle is fully
loaded). The driver notices this function through a reduction of pedal
force and increased pedal travel. When the brake pedal is released,
full braking assist switches off again automatically.
If there is an ABS failure, the brak e assistant and automatic full
braking assist are not available.
Th e brake assistant will not be operative if there is a ma lfunction in
the ABS .
_& WARNING
Please remember that the accident risk always increases if you
drive too fast, especially in corners or on a slippery road, or if you
follow the vehicle ahead of you too closely. Increased risk of an
accident cannot be compensated for even by the brake assistant ,
so always maintain a safe speed.•
Servotronic® -advanced power
steering system
The power steering systems uses the power of the
running engine to allow precise steering with little effort.
The advanced Servotronic ® power steering system senses the road
speed and electronically adjusts power assistance to provide
comfortable and safe steering response exactly matched to the
vehicle speed .
Power steering will not work if the engine is off. As a result , the
steering wheel will be hard to turn .
Th e power steering fluid level is checked during the scheduled main­
tenance services.
Vehicle care Do-it-yourself service Technical data

Intelligent technology
'-------------------------------------------------
Take into consideration that when you unlock your vehicle, some
convenience functions, such as the remote key or power seat adjust­
me nt, may not be available. The convenience functions will be avail­
able again when you turn on the ignition and start the engine.
With the engine turned off
If you listen to the radio, for example, with the engine turned off or
use other MMI functions, the battery is being discharged.
If start ing capability is jeopardized due to energy consumption, the
following warning appears in the MMI display:
Please start engine, otherwise system will switch off in
3 minutes .
The warning indicates that the system will be turned off automati­
cally after 3 minutes. If you wish to continue using the functions, you
have to start the engine.
With the engine running
Although electrical energy is generated when the vehicle is being
driven, the battery can become discharged. This happens mostly
when little energy is being generated and a great deal consumed and
the battery's state of charge is not optimal.
To bring the energy balance back into equilibr ium, consumers which
require especially large amounts of energy are temporarily cut back
or switched off. Heat ing systems in particular require a great deal of
energy. If you notice, for example, that the heated seats* or the
heated rear window are not heating, they have been temporarily cut
back or switched off. These systems will be available again as soon as
the energy balance has been restored .
You will also notice that engine idle speed has been increased
slightly. This is norma l and not a cause for concern. By increasing
engine idle speed the additional energy required is generated and the
battery is charged.
Driver notification in the instrument
cluster display
If battery power drops into the range where it can limit the ability of
the engine to start, this is shown in the instrument cluster display
with the following driver message:
i...-3 Low battery charge: battery will be charged while driving
This notification reminds you that the starting capability of the
engine may be limited. As soon as you start driving again, the battery
w ill be recharged and the notification will go out.
Driver notification appears and goes out again
If th is driver notification appears after the ignition is turned on or
whi le driving and it goes out again after a while, the battery has been
adequately recharged.
Driver notification appears and does not go out
again
If this driver notification appears after the ignition is turned on o r
wh ile driving and does not go out again, the battery's state of charge
is not in the optimal range. Starting ability is restricted. Have the
battery checked as soon as possible by an authorized Audi dealer or
qualified workshop. •

• Driving and environment
------------------------------------------------'
ffi For the sake of the environment
Even when the Emission Control System is operating properly, the
exhaust gas can have a sulfur-like exhaust gas smell under some
operat ing states. This depends on the sulfur content of the fue l being
used. Using a different brand of fuel may help, or filling the tank with
lead-free supe r grade gasoline. •
Applies to vehicles: with d iesel engine
Diesel particulate filter
The diesel particulate filter filters nearly all of the soot particles out
of the exhaust. The filter cleans itself automatica lly under norma l
driving conditions. If the filter cannot clean itself (for example,
because you are only driving short distances), the fi lter becomes
clogged with soot and the symbol for the diesel particulate filter
illuminates ~
page 40.
& WARNING
• Do not park your vehicle over flammable materials such as
grass or leaves because the high temperature of the diesel partic­
ulate filter could start a fire.
• Do not apply an underbody protectant in the exhaust system
area or a fire could start. •
Avoid damaging the vehicle
When you are driving on poor roads, or over curbs, steep ramps, etc.,
make certain that low-lying parts such as spoilers and exhaust system
parts do not bottom out and get damaged.
Thi s is espec ially true for vehicles with low-slung chassis (sports
chassis)" and fully loaded vehicles. •
Controls and equip­
ment Safety first Vehicle operation
Operate your vehicle economically
and minimize pollution
General
Your personal
style of driving will determine the economy
of your vehicle, as well as exhaust and noise levels.
Fuel economy, environmental impact, and wear on your engine,
brakes and tires largely depend on three factors:
• your personal dr iv ing style
• operating conditions
• technical limitations
If you anticipate what you need to do next and drive economically,
you can easily cut your fuel consumption by 10-15 percent. This
section will give you some tips on how you can he lp the environment
and your pocketbook.
(I) Tips
The consumption est imates as published by ENVIRONMENTAL
PROTECTION AGENCY (EPA) and Transport Canada may not corre­
spond to your actual consumption on the road, which will vary
depending upon vehicle load and speed, road and weather conditions,
trip length, etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are accelerating.
-Avoid unnecessary accelerating and braking.
Vehicles use the most fuel when they are accelerating . If you antici­
pate what is going to happen next, you will need to brake less and,
thus, accelerate less. Let the vehicle coast whenever possible - for
example when you see that the next traffic light is red. •
Vehicle care Do-it-yourself service Technical data

Driving and environment
Avoid full throttle
Driving at moderate speeds saves fuel and improves your
mileage.
-Try and keep well below your car's maximum speed.
Accelerating gently reduces fuel consumption, engine wear, and does
not disturb the environment.
Fuel consumption , exhaust emiss ions and eng ine no ise increase
disproportionately at high speeds . If you drive at approximately three
quarte rs of top speed, fuel consumption will be reduced by one ha lf.
Never drive faster than the posted speed limit and weather condi­
tions permit. •
Reducing unnecessary idling
Even when your car is just idling it burns up fuel.
- Shut the engine off when you are not driving the vehicle.
- Do not warm up the vehicle by letting the engine run at
idle .
It makes sense to shut off the engine in traffic jams, when waiting for
trains to pass at railroad crossings , or at traffic lights that have long
waits on red. Turning the engine off for just 30-40 seconds saves
more fuel than is burned starting the engine aga in.
It takes a long time for the engine to warm up fully when it is running
at idle . However, wea r and noxious emiss ions are especially high
when the engine is warming up. So you should drive away as soon as
you start the engine and avoid running at high rpms while the engine
is still warming up .
0 Note
Do not leave engine idling unattended after starting. If warning
lights should come on to indicate improper operation, they would go
unheeded. Extended idling also produces heat, which could result in
ove rheating or other damage to the vehicle or other property. •
Regular maintenance
A badly tuned engine unnecessarily wastes a lot of fuel .
-Have your vehicle serviced at regular intervals .
By having your vehicle regularly serv iced by an authorized Aud i dealer
helps to ensure that it runs properly and economically. The condition
of your vehicle not only affects its safety and ability to hold its value,
it a lso affects
fuel consumption.
Check your oil each time you fill your tank.
The amount of oil used is related to engine load and speed .
It is norma l for the oil consumption of a new engine to reach its
lowest value after a certain mileage has been d riven.
You must drive your vehicle about 3,000 miles (5,000 kilometers) befo re you can properly assess oi l consumption.
This also app lies to fuel consumption and engine output .
0 Note
• Have your veh icle ma inta ined properly and in accordance w ith the
service recommendations in your Warranty
& Maintenance booklet.
Lack of proper maintenance as well as im proper use of the vehicle will
impair the function of the emission control system and could lead to
damage .
• Do not alter or remove any component of the Emission Control
System un less approved by the manufacturer. ._

Driving off road
Driving off road
Driving in difficult road conditions
and offroad
General information
T he ope ra ti on of the Ele ctro nic Stabilization P rogr am ( ESP ) is
expanded for operation away from paved roads. In s ituations where
slip or a different ia l lock in g f unct io n is requ ired, t he ESP offroa d
mode can be activated~
page 256. Hill descent control is also avail­
able in the ESP offro ad mode, wh ich a utomatically bra kes the vehicle
and thereby keeps speed consta nt when d ifferent whee l speeds are
de te cted when descend ing a hill~
page 257. Your Audi also has
permanent all-wheel drive in add ition.
However , your Audi is not a pure offroad ve hicle.
It was not bui lt for
dr iv ing un der extreme cond it ions, e.g. for t rips that ar e in th e natur e
of an exped it io n.
Drive only on road s and offroad sections which match the design of
your vehicle and your abilities as a driver. Never take risks!
Before driving offroad
• Check the eng ine oi l level, tire pressure, coolant level, and the
fluid level in the w indshiel d wa sher rese rvoir.
• Stow luggage items and other objects in the luggage compart ­
me nt, and sec ure t hem agains t slid ing ar ound.
After driving offroad
• After tr ips offroad, remove a ny tw igs and other foreign objects
from the gr ill, the underbody an d the whee ls. Pay special attention to
fore ign obje cts (sto nes) wh ich have be come lodge d in the tire tr ead.
• Clean the body and the vehicle unde rside, and ins pect t he vehicle
for possib le dam age. •
Clean dirty w indows, headlamp lenses, rear lights, and lic ense
plates.
• Perform a bra ke check (pa rticul arly afte r travell ing t hrough
wate r).
& WARNING
• Drive especially attentively and plan ahead in difficult road
condit ions and when offroad. E xcessive speed or incorrect maneu­
vers can cau se injurie s and damage to the vehicle .
• Always adapt your speed and driving style to road, offroad,
traffic, and weather condition s. Drive especially slowl y offroad
when your view is restricted.
• Please be aware that in ESP offroad mode, particularly on a
smooth and slippery road, the wheels may have an increased
tendency to spin and the vehicle may break away - danger of skid­ ding!
• Stability i s limited in the ESP offroad mode.
Avoid dama ge to t he e nvir onment and respect nature .
[ i ] Tips
O nly drive where i t is permi tted and st ay on mar ke d roads an d
paths .
Explanation of some technical terms
The follow ing data refer to ideal conditions. Depending on vehicle
load and g round condi tions a nd the enviro nment, t he num bers may ...

Trailer towing
Driving with a trailer
General information Your Audi was design ed primarily for passenger transpor ­
tation .
If you plan to tow a t rai ler, p lease rem emb er that the add itiona l load
wi ll affect durab ility, economy and performance.
T railer tow ing not on ly p laces mo re s tress on the vehicle, it a lso calls
for more concentrat ion from the driver.
For this reason, a lways follow the ope rating and dr iv ing instr uctions
prov ided and use common sense .
(D Note
If you are going to tow a t ra iler , you must ac tivate the tra ile r ope ra­
tion mode ::::;,
page 182, "Towing a trailer". •
Technical requirements
Trailer hitch
Use a we igh t-car rying hit ch confo rm ing to the g ross tra ile r weig ht.
The hitch must be suitable for your vehicle and tra iler and must be
mou nted secure ly o n th e veh icle's chassis a t a
te chnically sound loca­
tion. Use only a trailer hitch with a removab le ba ll mount. Always
check w ith the tra iler h itch manufacturer to ma ke sure tha t you are
using the correct hitch .
Do not use a bumper hitch .
The hitch must be i nstalled in such a way t hat i t does not interfe re
w ith the impact-absorbing bumper system. No mod ificat ions should
Controls and equip­
ment Safety first Vehicle operation
be made to the vehicle exhaust and b
rake systems. From time to
time, check that all hitc h mounting bo lts rema in securely fastened.
Whe n you are no t towing a trai ler, remove the trailer hi tch ba ll
mount. This prevents the hitch from caus ing damage should your
vehicle be s truck from behind::::;,& .
Trailer brakes
If your trailer i s eq uipped w ith a b raking system, che ck to be s ure that
it conforms to all regulat ions.
T he tra iler hyd raulic brake system must not be directly connected to
the vehi cle's hydraul ic brake system ::::;, & .
Safety chains
Always use safety chains betwee n your vehicle and t he tra iler .
Trailer lights
Trailer lights must meet all regulat ions. Be sure to check w ith your
au thor ized A udi deale r for co rrect wi ring, switc hes, and re lays.
Mirrors
If you are unab le to see the traff ic beh ind you us ing t he regular
outside m irro rs, then you
must install extended mirro rs. It is impor­
t an t th at yo u
always have cle ar vision to the re a r.
& WARNING
• If a trailer has electrical brakes please note that these brakes
are not activated by the factory-fitted control unit -ri sk of acci ·
dent!
• Afte r removing the trailer hitch, do not store it in your vehicle .
In case of sudden braking, the hitch could fly forward and injure
you or your passengers .
Vehicle care Do-it-yourself service Technical data

pressure label is located o n the dr iver's side B-pillar. Inflate trailer
t ires to tra ile r and t ire ma nufacturers' spec ifications.
Lights
T he headl ight settings shou ld be chec ked with the tr ailer attached
before driving off. Check to make sure both vehicle and trailer lights
are wo rking properly.
Safety chains
Be sure tra ile r safety cha ins are p roperly connected from the t rai ler
to the hitch on the vehicle. Leave enough slack in the chains to perm it
tu rning corners . When you install sa fe ty ch ains, ma ke sure they will
not drag on the road when you are driving.
T he chains should cross under the trai ler tongue to prevent it from
dropping in case of separation from the h itch .
0 Note
If you are goi ng to tow a trai ler , you must activate the trai ler opera­
tion mode =>
page 182, "Towing a trailer". •
Driving instructior,s
Driving with a trailer always requires e xtra care and
consideration.
To obtain the best possib le handling of ve hicle a nd trailer ,
please note the following :
- Do not tow a loaded trailer when your car itself is not
loaded.
- Be especia lly careful when pass ing other vehicles .
- Observe speed limi ts.
- Do not drive at the maximum pe rmissible speed.
Controls and equip­
ment Safety first Vehicle operation
- Always apply brakes early.
- Mo
nitor the temperature gauge.
Weight distri but ion
T owing a loaded trailer with an empty car results in a highly unstable
distribution of we ight . If t his cannot be avoided , drive at very low
speeds only to avoid the risk of losing steering control.
A "balanced" rig is easier to operate and control. This means that the
tow veh icle shou ld be loaded to the extent poss ible and permissib le,
wh ile keeping the tra ile r as lig ht as poss ible unde r the ci rc u mstances.
Whe never possible, transfer some cargo to the luggage compart ­
me nt o f the tow vehicle while observing tongue load requirements
and vehicle loading considerations.
Speed
The higher the speed, the more d ifficult it becomes for the driver to
control the r ig . Do not dr ive at the maxim um permiss ible speed .
Reduce your speed eve n more if load, weather or w ind conditions are
unfavorable -particular ly when going downhill.
Reduce vehicle speed
immed iately if the tra ile r shows the slightest
sign of swaying.
Do not tr y to stop the s wayi ng by a ccele rating .
Observe speed lim its. In some areas, speeds for veh icles towing
trailers are lowe r than for regular veh icles .
Always apply brakes early. When driving downhi ll, shift into a lower
gear to use the engine brak ing effect to slow t he ve hicle . Use of the
brakes alone can cause them to overheat and fa il.
Coolant temperatur e
The coo lant temperature gauge=> page 10 must be observed care­
fu lly. If the needle moves close to the upper end of the sca le, reduce
speed immediately and/or turn off the air conditioner.
If the coo lant temperature warning light in the instrument clus ter
starts flash ing
- F- , pull off the road, stop and let the engine idle for
about two m inutes to prevent hea t buil d-up.
Vehicle care Do-it-yourself service Technical data

-~_C_ le_ a_n_ i_ n_ g=- a_ n_d___. p_ ro_ t_e _c_ t_ i_o _n ___________________________________________ _
Cleaning and protection
General information
Regular care preserves vehicl e val ue.
Any automobile is exposed to industria l fumes, co rrosive road salt,
e tc. A well ca red for Audi c an look lik e new many ye ars after pur cha se.
Regu lar and correct care w ill contribute to mai nta in ing t he bea uty
a nd valu e of your Au di.
Furthermore, good care may be a condition for substantiating a
warranty claim should corrosion damage or paint defects occur.
Yo ur au thori zed Audi d eale r h as a var iety of dedicated vehicle-care
products
and can advise w hich ones to use for clea ning the exterior
a n d inter io r of your ve hicle.
W het her you use products recommended by Aud i or other comme r­
cia lly availab le cleaning agents , please make sure yo u appl y them
co rrectly .
& WARNING
• Cleaning agents may be poisonous . Keep them out of the reach
of children.
• Heed all caution labels .
• Always read directions on the container before using any
product. Follow the directions carefully.
• Most chemical cleaners are concentrated and have to be
diluted .
• Use spot removing fluids only in well ventilated areas.
• Do not use gasoline, kero sene , diesel fuel , nail polish remover
or other volatile fluids . They may be toxic, flammable or
hazardous in other ways. Do not wash, wax or dry the vehicle with
the ign ition on or the engine running .
& WARNING (continued )
• Do not clean the under sides of chassi s, fenders , wheel covers,
etc. without protecting your hands and arms. You may cut your­
self on sharp-edged metal parts.
• Moisture and ice on brakes may impair braking efficiency
~ page 259, "General information ". Test the brakes carefully
each time you wash the vehicle .
'£> For the sake of the environment
Select only envir onmenta lly fr iendly clea ning produc ts . Leftover
cleaning pro ducts sho uld not dis posed of i n the household waste .•
Care of exterior
Washing
F re quent w ashin g protec ts th e vehicle.
T he best protection aga inst env ironmental influences is frequent
w ashi ng and w ax ing. How oft en thi s is requ ired depen ds on :
• How m uch the vehicle is used
• Whe re the ve hicle is parke d (gar age, in the o pen un der tr ees, etc.)
• The seasona l and weather conditions
• Environ mental influences
T he longer bird droppings , insects , tree resin, road and industria l
gr ime, t ar, soo t, road sa lt and o ther ma ter ia ls remain on t he veh icle
body, the more lasti ng their destructive effects w ill be. H igh temper­
atu res cause d by ex pos ure to intense s unlight int ensify the co rrosive
effect, part icu larly when humid ity is high as we ll.
~