oil temperature AUDI Q7 2015 Owner´s Manual

M
"' 0 _,
"". rl I.O
"' rl
"' rl
Instrument s and warning /indicator lights 11
too high, or the coolant level is too low
¢ page 32.
If the needle is well in the upper area of the
ga uge , the coolant temperature is too high.
Stop the vehicle , switch the eng ine off and
allow the engine to cool.
If the warning light
comes on again after driving a short distance,
contact an authorized dealer.
A WARNING
- Always observe the warning in
¢
page 256, before opening the hood
and checking the engine coolant level.
- Never open the engine hood if you see or
hear steam, or if you see engine coolant
dr ipping from the engine compartment.
You could bu rn yourself. Let the engine
cool off first until you can no longer see
or hear steam or coolant escaping.
0 Note
- Mount ing additional lights or accessories
i n front of the a ir inlets reduces the cool­
i ng effect of the radiator. At h igh outside
temperatures or high eng ine load , the
engine could overheat.
- The front spo iler has been designed to
properly distribute the cooling air when
the veh icle is moving. If the spoiler is
damaged, this cou ld reduce the cooling
effect and the engine could then over­ heat. Ask your authorized Audi dealer for
ass istance.
Tachometer (engine rev counter)
The tachometer indicates the engine RPM
(revolutions per minutes).
The tachometer @¢ page 10, fig. 3 is the left
of the two large clock-type displays.
The engine turns at a speed 1,000
times the
single digit in the display, e.g . if the needle is
pointing at the "2" the engine is turning at
2,000 RPM.
If engine RPM drops be low 1,500, you should
downshift to the next lower gear. The red area at
the end of the scale indicates maximum
permissible engine RPM after the break-in pe­
riod. Before reaching this area , move these­
lector lever to position D (Drive) or ease your
foot off the accelerator pedal.
(D Note
The tachometer needle should not move
into the red range. If it does, then only for
a very short per iod of t i me. You could
damage your engine by driving at high RPM .
@) For the sake of the environment
Upshifting early saves fuel and reduces en­
gine noise .
Digital clock with date display
Fig. 4 In st ru m en t cluster : time a nd da te
The date, time of day, and time and date for ­
mat can be set in the MMI. You can learn more
about this in the MMI manual.
(D Tips
-When open the driver door, the time,
date and odometer are disp layed for an
add itional 30 seconds.
- You can also call up the display with the
!CHECK I button q page 12 while the ig­
nition is sw itched off.

108 On the road
Starting and stopping
the engine
Starting the engine
The engine can only be started with your orig­
inal Audi key.
Fig. 123 I gni tion key positio ns
Vehicles with gasoline engine:
.. Step on the brake .
.. Move the selector lever into P or N
~ ,&. .
.. Tu rn the ignition key to position @
~ fig. 123 -do not depress the gas pedal
when starting the engine.
Vehicles with diesel engine:
.. Step on the brake .
.. Move the selector lever into P or N
~ ,&..
.. Turn the ign ition key to position ©- the
glow plug indicator light
II illuminates
when the glow plug system is act ive .
.. When the indicator l ight
II switches off,
turn the ignition key to pos it ion @ but do
not press the accelerator pedal.
.,. Re lease the ignition key once the engine
sta rts. The starter must not continue run­
ning.
A cold engine may sound loud after it has
been started . This is due to the hydraulic
va lves building up oil pressure. This is normal
and is not a need for concern.
If the engine does not start immediately, stop
trying after 10 seconds and then try to restart
the engine abo ut 30 seconds later.
Glow plug system*
Diesel engines are equipped with a glow plug
system whose preheating t ime is controlled by the coo
lant and outs ide temperature . Start
the engine
immediately after the glow plug
indicator light
II switches off.
The glow plug indicator light will only illumi­
nate for approximate ly 1 second when the en­
gine is warm or the outside temperature is
higher than 46 °F (8 °C). That means you can
start the engine
immediately .
A WARNING
-Never start or let the engine run in a con-
fined or enclosed area. Exhaust fumes
from the engine contain carbon monoxide,
a colorless and odorless gas . Carbon mon­
oxide can be fatal if in haled.
- Never leave the engine idling unattend­
ed. An unattended veh icle w ith a runn ing
engine poses a danger of personal injury
or theft .
(D Note
- Avo id high engine speeds, fast accelera­
tion or heavy engine loads while the en­ gine is still cold. This could damage the
eng ine .
- Th e engine cannot be started by pushing
or towing the vehicle .
@ For the sake of the environment
To avoid unnecessary engine wear and to
reduce exhaust emissions, do not let your
vehicle stand and warm up. Be ready to
drive off immediately after starting your
vehicle. Maintain moderate speed until the
engine is completely warm . Remember,
the engine performs best at operating
temperature.
· Stopping the engine
.,. Turn the ignition key to posit ion @
~page 108, fig . 123.
A WARNING
-
- Never turn off the engine until the vehi-
cle has come to a complete stop.

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
-The brake booster and servotronic on ly
work when the engine is running. With
the ignition turned off, you have to apply
more force when steering or braking .
S ince you cannot steer and stop normal­
ly, this can lead to accidents and ser ious
injuries.
- The rad iator fan can continue to run for
up to 10 min utes even after you have
turned off the engine and removed the ign ition key. The radiator fan can also
turn on again if the engine coolant heats
up because of intense sunlight or heat
build -up in the engine compartment.
«I) Note
Do not stop the engine immed iate ly after
hard or extended dr iving. Keep the engine
running for approximately two minutes to
prevent excessive heat build-up .
Starting and stopping
the engine with
Convenience key
Starting the engine with the~
button
App lies to vehicles: with Convenie nce key
This bu tton swi tches on the ign ition and
starts the engine .
Fig. 124 Co nvenie nce k ey: ENG INE START b utton
The I STAR T! button is provided w ith two -sta ge
o p era tion
¢ fig. 124.
Sw itching the ignition on
.. Press the !STAR T I button once to the firs t
stage to switch on only the ign ition .
On th e road 109
Gasoline eng in e: St arting the engine
.. Step on the brake.
.. Move the s elector lever to the P or N posi­
tion ¢.&, .
.. Press th e
r:: 1s =T:--:- A=RT= i button to the secon d
stage to start the engine .
Diesel en gine : Starting the engine
.. Step on the brake.
.. Move the selector lever to the P or N posi­
tion ¢.&, .
.. Press th e
r:: 1s =T A c:--=RT= I button down to the first
level to begin the preheating process . The
glow plug indica tor light
II illum ina tes
when the glow plug sy stem is active .
.. When the ind icator light
II switches off,
press the
I ST ART ! button down to the se c­
ond
level to star t the eng ine .
After a cold engine is started, there may be a br ief period of inc reased no ise because oil
pressure must first build up i n the hydraulic
valve adjuste rs. This is norma l and not a cause
for concern .
If the engine does not start immediately, stop
trying after 10 seconds and then try to restart
the engine abou t 30 seconds later .
Glow plug system*
Die sel engines
are equ ipped with a glow plug
system whose preheating time is controlled
by the coo lant and outs ide temperature . Start
the engine
immediately afte r the glow plug
indicator light
II swi tches off .
The glow plug indicator light will only illumi ­
nate fo r approximate ly 1 second when the en­
gine is warm or the outs ide temperature is
highe r than 46 °F (8 °C) . That means yo u can
start the eng ine
immediately .
WARNING
Never allow the engine to run in confined
spaces -danger of asphyxiation .
(D Note
-Avo id h igh engine rpm, full thrott le and
heavy engine loads until the eng ine has

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Catalytic converter
Applies to vehicles: with gasoline engine
It is very important that your emission con­
trol system (catalytic converter) is function­
ing properly to ensure that your vehicle is run­
ning in an environmentally sound manner .
... Always use lead-free gasoline c::> page 248,
Gasoline .
... Never run the tank down all the way to emp­
ty .
... Never put too much motor oil in your engine
c::> page 261, Adding engine oil 't=r..
.,. Never try to push-or tow-start your veh icle.
The catalytic converter is an eff icient "clean­
up" device built into the exhaust system of
the vehicle. The catalytic converter burns
many of the pollutants in the exhaust gas be­
fore they are released into the atmosphere.
The exclus ive use of unleaded fuel is cr it ically
i mportant for the life of the cata lytic convert­
e r and proper functioning of the engine.
& WARNING ,~
T he temperature of the exhaust system is
high, both when driving and after stopping
the engine .
- Never touch the exha ust tail pipes once
they have become hot. This could result
in burns.
- Do not park or operate the vehicle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fuel spill or other material which can
cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust
manifold, exhaust p ipes, catalytic con­
verter or heat shields . During driving, the
substance used for undercoating cou ld
overheat and cause a fire.
(D Note
- Be aware that just one tank f illing with
leaded fuel will already seriously de-
grade the performance of the catalytic
conve rter.
Dri vin g and en vironm ent 231
-Do not exceed the correct engine oil level
c::> page 261.
- Do not drive until the fue l tank becomes
completely empty. The engine cou ld mis­
fire. Unburned fuel could also get into
the exhaust system and this cou ld cause
the catalytic converter to overheat.
- Do not turn off the ignition while the ve­
hicle is mov ing.
- Do not continue to operate your veh icle
under these conditions, as otherwise fuel
can reach the catalyt ic converter. Th is
cou ld result in overheating of the con­
verter, requir ing its replacement.
- To assure efficient operation of the Emis­
sion Control System:
- Have you r vehicle main tained properly
and in accordance w ith the se rv ice rec­
ommendations in your Warranty & Maintenance book let.
- Lack of proper maintenance as we ll as
improper use of t he vehicle will impair
the function of the emission contro l
system and could lead to damage.
@) For the sa ke of the env ironment
Even when the Emission Control System is
operating properly, the exhaust gas can have a sulfur-like exhaust gas smell under
some operat ing states. This depends on
the sulfur content of the fuel being used .
Using a different brand of fuel may help,
or filling the tank with lead-free s uper
g rade gasoline.
Diesel particulate filter
App lies to vehicles: wit h diese l eng ine
The diesel part iculate filter filters nearly all of
the soot pa rticles out of the exhaust . T he fil­
te r clea ns itself automat ica lly under no rma l
driv ing cond itions. If the filter cannot clean it ­
self (for example, because you are on ly driving
short distances), the fi lter becomes clogged
with soot and the
II symbol for the diese l
particulate filter i lluminates
c::> page 36. ..,_
•
•

232 Driving and en vironm ent
,8. WARNING
-Do not park your vehicle over flammable
materials such as grass or leaves because
the high temperature of the diesel par­
t icu late filter could start a fire .
- Do not apply an underbody protectant in the exhaust system area or a fire could start.
Avoid damaging the vehicle
When you are driving on poor roads, or over
curbs, steep ramps, etc., make certain that
low-lying parts such as spoilers and exhaust
system parts do not bottom out and get dam­
aged.
This is especia lly true for vehicles with low­
slung chassis (sports chassis)* and fully load­
ed vehicles.
Shutting down vehicle
If you would like your vehicle to remain inop­
erative for a longer period of time, contact an
Audi or other specialized dealer . They can ad­
vise you on necessary precautions e.g . corro­
sion prevention, maintenance and storage. Pay attention to additional information con ­
cerning the battery. Refer to
c::> page 266 .
Operate your vehicle
economically and
minimize pollution
General
Your personal style of driving will determine
the economy of your vehicle, as well as ex­
haust and noise levels .
Fuel economy, environmental impact, and
wear on your engine, brakes and tires largely
depend on three factors:
- your personal driving style
- operating conditions
- technical limitations
If you anticipate what you need to do next and
drive economically, you can easily cut your
fuel consumption by 10-15 percent . This sec­
tion will give you some tips on how you can help the environment and your pocketbook.
(D Tips
The consumption estimates as published by ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the road, which will vary depending upon vehi­
cle load and speed, road and weather con­
dit ions, trip length, etc.
· Drive smoothly and keep a lookout
ahead
Vehicles use the most fuel when they ore ac­
celerating.
., Avo id unnecessary accelerating and brak ing .
Vehicles use the most fuel when they are ac ­
celerating . If you anticipate what is going to
happen next, you will need to brake less and,
thus, acce lerate less. Let the vehicle coast
whenever possible -for examp le when you see
that the next traffic light is red.
Avoid full throttle
Driving at moderate speeds saves fuel and
improves your mileage.
., Try and keep well below your car's maximum
speed.
Accelerating gently reduces fuel consump­
tion, engine wear, and does not disturb the environment.
Fuel consumption, exhaust emissions and en­
gine noise increase disproportionately at high
speeds. If you drive at approximately three
quarters of top speed, fuel consumption w ill
be reduced by one half. Never drive faster
than the posted speed limit and weather con­
ditions permit.

M N
0 ..J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Reducing unnecessary idling
Even when your car is just idling it burns up
fuel.
11-Shut the engine off when you are not driving
the vehicle.
11-Do not warm up the vehicle by letting the
engine run at idle .
It makes sense to shut
off the engine in traffic
jams, when waiting for trains to pass at rail­
road cross ings, or at traffic lights that have
long waits on red. Turning the engine
off for
just 30-40 seconds saves more fuel than is
burned starting the engine again.
It takes a long time for the engine to warm up
fully when it is running at idle. However, wear
and noxious emissions are especially high
when the engine is warming up. So you should
drive away as soon as you start the engine and
avoid running at high rpms while the engine is
still warming up .
(D Note
Do not leave engine idling unattended af­
ter starting. If warning lights should come
on to indicate improper operation, they
wou ld go unheeded. Extended idling also
produces heat, which cou ld result in over­
heating or other damage to the vehicle or
other property .
Regular maintenance
A badly tuned engine unnecessarily wastes a lot of fuel .
11-Have your vehicle serviced at regular inter-
vals.
By having your vehicle regularly serviced by an
authorized Audi dealer helps to ensure that it
runs properly and economically. The condition
of your vehicle not only affects its safety and
ab ility to hold its value, it also affects fuel
consumption.
Check your oil each time you fill your tank.
Driving and environment 233
The amount of oil used is re lated to engine
load and speed.
It is normal for the oil consumption of a new
engine to reach its lowest value after a certain
mileage has been driven.
You must drive your vehicle about 3,000 miles
(S,000 kilometers) before you can properly
assess oil consumpt ion.
This also app lies to fue l consumption and en­
gine output.
(D Note
- Have your veh icle ma inta ined properly
and in accordance with the service rec­
ommendations in your Warranty
& Main­
t enance booklet. Lack of prop er mainte­
nance as well as improper use of the ve­
hicle will impair the function of the
emission cont ro l system and could lead
to damage.
- Do not alter or remove any component of
the Emission Control System unless ap­
proved by the manufacturer.
- Do not alter or remove any device, such
as heat shields, switches, ignition wires,
valves, which are designed to protect
your vehicle's Emission Control System and other important vehicle compo­
nents.
Fewer short trips
Fuel consumption will always be relatively
high on short trips .
11-Try to avoid driving short distances w ith a
cold engine.
T he engine and cata lytic converter have to
reach their optimal operating temperature to
reduce fuel consumpt ion and noxious emis­
s ions effectively .
Just after starting, a co ld engine in a mid-size
car only achieves a fuel economy of 6-8 mi les
per gallon (30-40 l/l00km). After about a
half a mile, fuel economy climbs to 12 mpg
(20 l/100 km). After about
2.5 miles (4 km), liJI,
•
•

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
-Blend must contain not more than 1S%
MTBE.
Seasonally adjusted gasoline
Many gasoline grades are blended to perform
espec ially we ll for winter or summer driving.
During seasonal change-over, we suggest that
you fill up at busy gas stat ions where the sea­
sonal adjustment is more likely to be made in
time .
(D Note
-Methanol fuels which do not meet these
requirements may cause corrosion and
damage to plastic and rubber compo­
nents in the fuel system.
- Do not use fue ls that fail to meet the
specified criter ia in this chapter.
- If you are unable to determine whether
or not a particular fue l blend meets the
specifications, ask your service station or
its fuel supp lier.
- Do not use fuel for which the contents
cannot be identified.
- Fuel system damage and performance
problems resulting from the use of fuels
different from those specified are not
the responsibility of Audi and are not
covered under the New Vehicle or the Emission Control System Warranties.
- If you experience a loss of fuel economy
or driveability and performance prob­ l ems due to the use of one of these fuel
blends, we recommend that you switch
to unblended fuel.
Gasoline additives
Applies to vehicles : wit h gasoli ne e ng in e
A majo r concern among many auto manufac­
ture rs is carbon deposit build-up caused by
the type of gasoline you use.
Although gasoline grades differ from one manufacturer to another , they have certain
things in common. All gasoline g rades contain
substances that can cause deposits to collect
on vital engine parts, such as fuel injectors
and intake valves. Although most gasoline
Fuel supply and filling your fuel tank 249
brands include additives to keep engine and
fuel systems clean, they are not equally effec­
tive .
Audi recommends using TOP TIER Detergent
Gasoline . For more information on TOP TIER
Detergent Gasoline, please go to the official
webs ite (www.toptiergas.com).
After an extended per iod of using inadeq uate
fuels, carbon deposit build-ups can rob your
engine of peak performance.
CD Note
Damage or malf unct ion due to poor fuel
quality is not covered by the Audi New Ve­
hicle Limited Warranty.
Diesel fuel
Applies to veh icles: w ith diesel engine
Always use ULSD (Ultra Low Sulfur Diesel)
No. 2. The ULSD No. 2 meets the ASTM D97S.
Diesel fuel with concentrations of biodiesel
highe r than S % such as Bll, B2O or BlOO are
strictly prohib ited .
Se rv ice stat ion fuel pumps are labeled with
the cor rect fuel informat ion for easy recogn i­
tion by the user. If the diesel fuel pump is not
labeled ask the station operator what fuel is
being dispensed before filling up your vehicle.
ULSD No. 2 may not be available outside the
USA and Canada. Be sure to check before trav­
eling to other countries .
ULSD No. 2 can become thicker in very cold
temperatu res, and this can impair the en­
gine's start ing and running. Depending on the
season, gas stations provide ULSD No. 2 that
flows better in cold temperatures so that you
can continue operating your vehicle as usua l.
CD Note
-Yo ur vehicle's diesel engine was de­
signed soley for use with ULSD No. 2.
Therefore, never use gasoline, heating oil, other fuels or flow improvers. These
conta in substances that will severely
damage the fuel system and the engine . .,.
•
•

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-Apply the parking brake.
- Move selector lever to P (Park).
- Always let the engine cool down. Hot
components will burn skin on contact.
- To reduce the risk of being burned, never
open the hood if you see or hear steam
or coolant escaping from the engine
compartment. Wait until no steam or
coolant can be seen or heard before care­
fully opening the hood.
- Keep children away from the engine com­
partment .
- Never spill fluids on hot engine compo­
nents. They can cause a fire.
- Never touch the radiator fan. The auxili­
ary electric fan is temperature controlled
and can switch on suddenly.
- Never open the coolant reservoir cap
when the engine is still warm. The cool­
ant system is pressurized and hot cool­
ant could spray out .
- Protect your face, hands and arm from
steam or hot engine coolant by placing a
thick rag over the cap when you open the
coolant reservoir .
- Do not remove the engine cover under
any circumstances . This increases the
risk of burns.
- If work on the fuel system or the electri­
cal system is necessary:
- Always disconnect the battery .
- Never smoke or work near heaters or
open flames. Fluids in the engine com­
partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and personal in­
jury while the engine is running or being
started, never touch:
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repair
with the engine running:
Checking and filling 257
- First, fully apply the parking brake,
move selector lever to P (Park).
- Always use extreme caution to prevent
clothing, jewelry, or long hair from get­
ting caught in the radiator fan, V-belts
or other moving parts, or from contact­
ing hot parts . Tie back hair before
starting, and do not wear clothing that
will hang or droop into the engine.
- Minimize exposure to emission and
chemical hazards~&. .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the State of
California to cause cancer and birth de­
fects and reproductive harm. In addition,
certain fluids contained in vehicles and
certain products of component wear con­
tain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
Q) Note
When adding fluids, always make sure that
they are poured into the proper container
or filler opening, otherwise serious dam­
age to vehicle systems will occur .
@ For the sake of the environment
To detect leaks in time, inspect the vehicle
floor pan from underneath regularly . If
you see spots from oil or other vehicle flu­ ids, have your vehicle inspected by an au­
thorized Audi dealer. •
•

M N
0 ..J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Adding engine oil~
Fig. 2 45 Eng ine co mpa rtment : cove r on the e ngin e o il
filler neck
Before you c heck anything in the engine com­
partment,
a lw ays r ead and h eed all WARN ­
ING S
9 A in Working in the engine compart­
ment on page 256 .
"' Shut the engine off.
"' Unsc rew the cap~ to the engine oil fill ing
hole
9 fig . 245, 9page 258, fig. 242 .
"'Carefu lly top off with 0.5 q uarts (0.5 liters)
of the appropriate oi l
9page 258.
"'Check the oil leve l again after two minutes
9 page 260, Checking the engine oil level.
"' Top off the oil again, if necessary.
"' Screw the cap back on the filling hole and
slide the oil d ipst ick in as far as it will go .
A WARNING
Stop! Before working in the engine com­
pa rtment, always read and heed all WARN­
INGS
9 .&. in Working in the engine com ­
partment on page 256.
The engine com ­
partment of any motor vehicle is a poten­
tially dangerous area and can cause ser i­
ous personal injury.
A WARNING
Spilled o il is a fire hazard.
- The oil fille r cap must be properly se­
c u red to prevent oil from being sprayed
on the hot engine and exhaust system
when the eng ine is running.
- The oil leve l must not be above range ~
- danger of converter or eng ine damage!
Checkin g and fillin g 261
Contact an authorized deale rship to draw
off oil, if necessary .
-Audi doe s not re commend the u se of oil
additives. They m ay damage the engine
and ad ve rse ly affe ct you r New Vehicle
War ra nty.
@ For the sake of the environment
- Under no circumstances can the oil come
in contact with the sewage network or
the soi l.
- Observe and follow legal regulations
when disposing of empty oil containers .
· Changing the engine oil
Engine oil must be changed at intervals listed
in the Warranty
& Maintenance booklet.
T he eng ine oi l and oil fi lter m ust be changed
accord ing to the mileage and time intervals
specified in yo ur vehicle's Warranty
& Mainte­
nance booklet. Do not exceed these intervals -
harmful s ludge and deposits from old engine
o il can reduce engine performance and can
lead to expens ive engine repa irs .
Changing oi l at reg ular intervals is so very im­
portant because the lubricat ing properties of
o il decrease gradually during normal vehicle
use. If you are not sure when to have the oil
c h anged, ask your authorized Audi Serv ice Ad­
viso r.
Under some circumstances the engine oil
shou ld eve n be changed more often than
spec ified for normal use. Change o il more of­
ten if you often dr ive short d istances , operate
the ve hicl e in dusty a reas or mostly under
stop- and-go t raffic conditions, or when you
use your veh icle where temperatures stay be ­
l ow freezing point for long periods.
Dete rgent additives in the oil will make fres h
o il look dark after the engine has been ru n­
ning for a sho rt time. This is normal and is not
a reaso n to change the oil more often than
recommended.
ll>-
•
•

26 2 Ch eck ing and filling
8_ WARNING
Stop! Before working in the engine com­
partment, always read and heed all WARN ­
INGS
~ .&. in Working in the engine com­
partment on page
256 . The engine com­
partment of any motor veh icle is a poten­
tially dangerous area and can cause ser i­
ous personal injury.
8_ WARNING ,,,__
If you must change the engine oil in your
vehicle:
- Always wea r eye protection .
- T o reduce the ris k of burns from hot en-
gine oil let the engine cool down to the
touch.
- Whe n removing the oil drain plug with
yo ur fingers, stay as far away as poss ible.
Always keep your forearm paralle l to the
ground to he lp prevent hot oil from run­
ning down your arm.
- Drain the oi l into a container designed
for this pu rpose, one large enough to
hold at least the total amount of oil in
your engine.
- To reduce the risk of poisoning, never use
empty food or beverage containers that
might m islead someone into dr ink ing
from them.
- Engine oil is poisonous. Keep it well out
of the reach of children.
- Cont inuous contact with used engine oil
is harmful to your skin. Always protect
your sk in by washing thoroughly with
soap and water .
(D Note
Never mix oil additives with your engine
oil. These additives can damage your en­
gine and adverse ly affect your Audi Limit­
ed New Vehicle Warranty.
@i For the sake of the environment
- Before changing the oil, first make sure
you know where you can properly dispose of the old oil.
-
.
- Always dispose of used oil p roperly. Nev ­
er dump it on garden soil, in wooded
areas, into st reams or down sewage
dra ins.
- Recycle used oi l by taking it to a used en­
gine oil collection facility in your area, or
contact a service station.
- We strongly recommend that yo u have
your oil changed by an authorized Audi
dealer or a qualified workshop with the
special tools and expert ise required, and
proper means of disposal.
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro­
tects the engine from freezing in the winter.
T he cooling sys tem is sealed and genera lly re­
quires little attention.
The cooling system has been fi lled at the fac­
tory with a permanent coolant which does not need to be changed. The coo lant cons ists of a
mixtu re of specially conditioned water and the
manufacturer's g lycol -basedcoo la nt add
i-
tive G l3 antifreeze with anticorrosion addi ­
tives (SO% for USA mode ls; 60% for Canadian
models). This mixture both assures the neces­
sary frost protection and protects metal com­
ponents in the eng ine's cooling system from
corros ion and scaling.
It also ra ises the bo il­
i ng po int of the coolant .
Do not reduce the concentration of the cool­
ant in the summer by adding p lain wate r. Th e
proportion of coo lant additiv e mu st be at
l e as t 50 °/4 but not m ore than 60°/4
to main­
ta in ant ifreeze protect io n and cooling eff ic ien­
c y.
If the coo lant fros t protection is too low,
the coolant could freeze and damage the vehi­
cle heating and engine cooling system.
For year- round driving, antifreeze is added at
t h e factory fo r temperatures down to:
- -31°F(-35°C)USA
- - 40 °F ( - 40 °C) Canada.