wheel AUDI R8 SPYDER 2012 Repair Manual

soon as possible, and inflate them to the
proper pressure . Driving on a significant ly un­
der-inflated tire causes the tire to overheat
and can lead to tire failure. Under-inflation a l­
so reduces fuel efficiency and tire tread l ife,
and may affect the veh icle 's handling and
stopping ab ility.
Please note that the TPMS is not a substitute
for proper t ire maintenance, and it is the dr iv­
er's responsib ility to ma inta in correct t ire
p ress ure , even if under- inflation has not
reached the leve l to t rigger illumination of the
TPMS low tire pressure telltale .
Your veh icle has also been equ ipped with a
TPMS malfunction indicato r to indicate when
the system is not ope rating properly. The
TPMS malfunc tion indica to r i s combined wi th
the low t ire pr essu re tellta le. When the sys ­
tem detec ts a ma lf u nct ion, the te lltale will
flash for approximately one minute and then remain continuo usly ill uminated . This se­
q uence will continue upon subsequent vehicle
start-ups as long as the malfunction ex ists.
When the malfunction indicator is ill uminat ­
ed, the system may not be able to detect or
signa l low t ire pressure as intended . TPMS
malfunct ions may occ ur for a variety of rea­
sons, including the ins talla tio n of replace­
ment or a lternate tires o r whee ls on the veh i­
cle that prevent the TPMS from funct io ni ng
p roperly . Always check the TPMS malfunct ion
t ellta le afte r replacing one o r more t ires or
wheels o n your veh icle to ensure tha t the re­
p lacemen t or a lternate tires and wheels allow
the TPMS to continue to function properly .
Introduction
The tire pressure monitoring system monitors
air pressure in all four road wheels while the
vehicle is moving .
As soon as the tire pressu re mo nitor ing sys­
tem senses a s ignificant loss of a ir pressure in
one or severa l ti res, text messages and yellow
symbo ls appear in the instr ument cluster dis ­
p lay to alert the driver. The
[ti warning light
Tire s an d wheel s 201
in the instrument cluster comes on when the
ti re is significant ly underinflated .
T he wa rni ng lig ht
[ti also illu minates i n the
case of a system mal funct io n.
Be aware that t ire pressure is a lso dependent
o n the tempe ratu re of the t ire. For eve ry 18 ° F
(10 °C) incre ase in tir e te mper ature, tire pres­
s u re inc reases by about 1.5 psi (0 .1 bar). The
ti re warms up while the ve hicle is moving and
tire p ress ure rises . So you sho uld ad just tire
pressure only when they a re
cold, when the
temperature of the tires is ro ughly the same
as the ambient a ir temperature.
In order to keep the tire press ure monito ring
system p roperly ca librated, t ire press ure on
all four tires sho uld be checked at regu lar in­
terva ls.
The tire pressure is shown on the label located
on the dr iver's side B-pillar (v is ib le when the
door is open) .
A WARNING
When the tire pressure mo nitoring system
war ning light is lit , one o r m ore of your
tires is s ignificantly under-infla ted . You
shou ld stop and check your tires as soon as
pos sib le, and in flate t hem to the proper
p ress ure a s in dic ate d on the ve hicle's ti re
p ress ure lab el
¢page 187. Driving on a
significantly under -inflated ti re causes t he
tire to over heat and can lead to tire failure .
Under-inflat ion also is like ly to impair the
vehicle's handling and stopping ab ility.
@ For the sake of the environment
D riving wit h un der -inflated tires red uces
fuel efficiency an d tire t read life.
(D Tips
- E ach tire should be chec ked monthly
w hen the tem perature of the tires is
about the same as amb ient a ir tempera­
t u re and set to the recommended infla­
tion press ure as specified on the tire
pressure label¢
page 187.
•
•

202 Tire s and whee ls
- The tire pressure monitoring system
helps the driver to keep an eye on tire
pressures. But the driver st ill has the re­
spons ibility for maintaining the correct
tire pressure.
- Tire pressure must only be adjusted
when the temperature of the tires is
about the same as ambient air tempera­
ture.
- When t ires are replaced, the sensors and
valves should not be exchanged . The
valve core, nut, valve sealing and seal
washer (rep lacement kit) needs to be re­
placed. If necessary, the valve and the
whee l electronics have to be rep laced.
- The tire pressure monitoring system on
your Audi was calibrated us ing tires w ith
"RO" identification. We recommend us­
ing these tires.
- If you should put different whee ls and
ti res on yo ur vehicle (e.g. w inter wheels
and tires), yo u m ust be certain that the
whee ls and tires are compatible with the
tire pressure monitoring system . Other­
wise the system w ill reg ister a ma lfunc­
tion and a fault message will be d is­
played . For more information, contact
your authorized Audi dealer .
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions
~ page 222 .
Programming a new set of tires
App lies to vehicles: with tire pressure monitoring system
When driving with a new set of ti res, you can
program them to the t ire pressure monitoring
system using the menu disp lay.
"' Turn the ign ition on.
"' Se lect the menu :
Set> Tir e pr essu re >
Wh eel cha ng e.
"' Co nfirm that you wou ld like to begin the
programming process. The message
Wh eel
s en sors a re being in it ia lised. Thi s ma y ta ke
a fe w minute s .. .
appears in the instrument
cluster disp lay. You can switch between programmed tire sets
at any time without reinitializing the system .
(D Tips
If the programming process was not com­
pleted successfully, the message
Wheel
s en sors could not be initi alis ed
appears in
the disp lay and the
IIQIS, indicator light
turns on. If this happens, repeat the pro­
cedure.

What do I do now? Trunk escape handle
Appl ies to vehicles: with trunk escape handle
In case of an emergency, the front lid can be
opened from the inside using the trunk es­
cape handle.
.. To open the front lid pull the handle.
The trunk escape handle inside the luggage
compartment is made of fluorescent materia l
to g low in the dark.
.&_ WARNING
The trunk escape handle is to be used only
in an emergency.
Breakdown kit
The breakdown kit consists of vehicle tool kit
and tire mobility system.
Fig. 152 Breakdown kit in luggage compartment
@ Vehicle tool kit
@ Tire mobility system c::> page 203
The breakdown kit is located in the luggage
compartment under the cargo floor .
The tool kit consists of the following items :
- Hook for removing hub cap
- Lug wrench
- Alignment pin for changing wheels
- Screwdriver w ith reversible blade
- Towing eye
- Jack* (not a vehicle component; contact your
authorized Audi dealer if needed)
Before returning the jack* to its place, retract
the jack arm fully .
What do I do now ? 203
Note: some of the items listed above are pro­
vided on certain mode ls only or are optional
extras.
.&_ WARNING
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts .
- The jack* (available as a replacement
part) is intended only for your vehicle
model. Under no circumstances use it to
lift heavy vehicles o r other loads; you risk
injuring yourse lf.
- Never start or run the eng ine while the
veh icle is supported by the jack *.
- If you must work under the veh icle, al­
ways use safety stands specifically de­ signed fo r th is purpose.
- Using a bumper jack to ra ise the vehicle
wi ll damage the bumpe r system. The
jack may slip, caus ing injury.
Tire repair
General and safety pointers
Tire repair is intended only for temporary,
short-term use .
Fig. 153 Ti re damage for which the Tire Mob ility Sys ­
tem is not suited
-
Your vehicle is equipped wi th a tire repa ir k it,
the
Tire M obility Sy stem (T M S).
In the event of a t ire failure, the TM S is in the
luggage compartment under the floor.
It con ­
s ists of the tire sealan t and an elec tric air
pump.

206 What do I do now?
• Switch the electric air pump off -switch in
position
0. If the required tire pressure of at
l east 1.8 bar has not been reached, it is not
poss ible to make a repa ir with the tire seal­
ant. Seek professional ass istance.
Disassembling Tire Mobility System
• Remove the hose from the valve and pull
the p lug out of the socket .
• Screw the dust cap onto the valve.
• Place the empty sealant bottle back in the
original packaging and clip it in place under
the floor so that no tire sealant can run out into the vehicle .
• Start driving r ight away so that the sealant
is distributed in the tire.
.&_ WARNING
- Follow the manufactur er's safety instruc­
tions on the decal for the air pump and
the sea lant bott le .
- If a tire pressure of 1.8 bar cannot be
achieved after pumping for 5 minutes,
the tire is too severely damaged. Do not continue to drive.
- Seek professional assistance if it is not
possible to repair the tire with the tire
sealant.
(D Tips
- Do not operate the electric air pump for
more than 8 min utes without stopping,
otherwise it can overheat. When the air
pump has cooled down, you can continue
to use it.
- If sealant has escaped, allow it to dry,
then you can peel it off.
Final check
After driving for a short distance, t ire pressure
must be checked .
• After driving for about 10 minutes, stop
and check the t ire pressure .
• If tire pressure is still at least 1.3 bar, in­
flate the tire to specified p ressure (see driv­
er's side B-pillar), drive to the next repair shop and have the tire and the sealant
bot­
tle replaced.
• If tire pressure is less than 1.3 bar, the t ire
is too severely damaged. Do not continue to
drive. Seek professional assistance.
.&_ WARNING
If tire pressure is less than 1.3 bar after
driving for 10 minutes, the tire is too se­
ve rely damaged. Do not continue to drive.
Seek professional assistance.
(D Tips
After a tire repair, have the sealant bottle
replaced at a dealership. This restores full
functionality to the Tire Mobility System .
What should I be
aware of when
changing a tire?
Tires with unidirectional tread design
-
Tires with unidirectional tread design must be
mounted with their tread pattern pointed the
right direction.
A unidirectional tire can be identified by ar­
rows on the sidewall, which point in the direc­
tion of the rotation. You must follow the
specified direction of rotation. This is necessa­
ry in order for these tires to develop their op­
timum characteristics regarding grip, road
noise, wear, and hydroplaning .
· Anti-theft wheel bolts
A special adopter is needed to turn the anti­
theft wheel bolts.
Fig . 156 A nti-theft wheel bolts wit h adapte r

.. Install the adapter @ as far as it wi ll go on ­
to the anti-theft wheel bolt
(D .
.. Push the wheel wrench over the adapter @
as far as it will go.
.. Loosen or tighten the wheel bolt
i=>page 209.
We recommend a lways keeping the wheel
bolt adapter with you in the vehicle . It should
be stored in the vehicle tool k it.
There is a
co de number for the wheel bolt
l ocking device, stamped on the face of the
adapter . You can use th is number to obtain a
replacement adapter at an authorized Aud i
dealership, if necessa ry .
{!) Tips
Write down the wheel bolt locking dev ice
code number and store it in a safe place,
away from the vehicle.
Raising the vehicle
Ap plies to vehicles: with origina l Audi jack
The vehicle must be li~ed with the jack* first
before the wheel can be removed.
•
Fi g. 157 Sill pane ls: markings
Fig. 158 Sill: posit ion ing the vehicle jack
0 co
~
"' ;g
The description for using the vehicle jack only
appl ies to the or ig inal jack* (no t a veh icle
What do I d o now ? 207
component; contact your authorized Audi
dealer if needed) .
.,. Engage the
parking brak e to prevent your
veh icle from rolling unintentionally .
.. Shift into 1st gear.
.. Find the
liftin g po int in the sill on the side
w ith the affected wheel
c:> fig. 157 .
.. Extend the jack under the lifting point on
the door s ill until its arm is positioned di­
rectly under the lifting point
c:> /.1. .
.,. Align the jack so that its arm @c::> fig. 158
engages in the designated lifting point in
the door s ill and the movable base @ lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point @ .
.. Wind the jack up further until the flat tire
comes
off the ground c:> /.1. .
Position the veh icle jack only under the desig­
nated lifting points on the sill ¢
fig. 157.
There is exactly one locat io n for eac h side of
the vehicle . The jack must not be positioned
at any other location
c:> & c:>Q) .
An un stable surfac e under the jack can cause
the ve hicle to slip
off the jack . Always provide
a firm base for the jack on the ground . If nec­
essary place a sturdy board or simi lar s upport
under the jack. On
hard , sl ipper y sur faces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping c::>
&.
A WARNING
-You or your passengers co uld be in jured
while changing a wheel if you do no t fo l­
low safety precautions:
- Position the vehicle jack on ly at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could slip a nd cause an injury if it does not
have sufficient hold o n the vehicle.
- A soft or unstable surface under the
jac k may cause the ve hicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessary, u se a st urdy board under the jack.

208 What do I do now ?
-On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- D o not raise the vehicle u nti l yo u a re
sure the ja ck is sec urely engaged.
- P assenge rs must not rema in i n the ve­
h icl e when it is ja ck ed up.
- M ake sure t hat passengers wait in a
safe p lace away fro m the vehicle and
well away from the road and traffi c.
- M ake sur e jac k position is correct, ad­
just as necessary and then co ntinue to
r ai se the j ack .
CD Note
A floo r jack or the pads o n the hoist arms
m ust
not be posit ioned at the points
s hown
-arrows-.
Remov ing the wheel
Follow these instructions step-by-step for
changing the wheel.
F ig. 1 59 Whee l change: alignment pin inside the top
hole
Afte r you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, perform the
following steps to remove a nd rep lace the
wheel :
Removing the wheel
" Use the hexagonal socket in the screwdri v­
er handle
to comp lete ly tu rn out the top­
most wheel bo lt and set it as ide on a
clean
surface. "
Sc rew the th readed end of the
alignment
pin
from th e tool kit hand-tight into t he
now vacant bolt ho le
c::> fig . 159.
" Then complete ly unscrew the other wheel
bolts as described above.
" Take off the whee l leaving the a lignment
p in in the bolt hole
c::>(D .
Putting on the wheel
" Lift the spare whee l and carefully s lide it
over the alignment pin to guide it in place
c::>(D .
" Use the hexagonal socket in the screwdriver
ha ndle to screw in and tighten a ll whee l
bolts
slightly .
" Uns crew the alignment p in and insert and
tighten the rem aining wheel bol t slightly
like the res t.
" Tur n t he jack hand le co unter-clockwise to
lower the vehicle until the jack is fully re­
leased.
T he wheel bo lts must be clean and turn easily.
Check the contact s urfaces of whee l and hub.
Remove contaminants on these surfaces be ­
fore insta lling the w heel.
T he hexagonal socket in the screwdriver ha n­
dle makes it easier to handle the w heel bo lts.
The reversible blade should be removed.
When mounting
unidirectional ti res, observe
the d irection o f rotation
c::> page 206.
CD Note
W hen remov ing or inst alling the whee l,
t he r im cou ld hi t the b ra ke ro tor and dam­
age the ro tor . Wor k caref ully an have a
second pe rson hel p you.
(D Tips
Neve r use the he xagona l socket in the han ­
d l e of t he screwdriver to loosen or tighten
the wheel bo lts .

Tightening wheel bolts
~ Fit the wheel bolt wren ch over the wheel
bolt and push it down as far as it will go
1l.
~ Close your gr ip around the end of the
wrenc h handle fo r maximum torque and
turn each whee l bolt
clockwi se u nti l it sits
t ight.
H ave the
tightening torque of the whee l bolts
checked as soon as possible with a torque
wrench. It shou ld be 120 Nm.
Chec k the
tir e pre ssure as soon as possible .
Return the vehicle tool kit to its proper place .
A WARNING
Loosening the wheel bo lts is prohib ited;
da nger of an accident!
@ Tips
- Never try and use the hexagona l socke t
i n the handle of the screwdr iver to loos­
en or tighten the w heel bolts.
- If yo u have dete rm ined t hat wheel bolts
a re cor roded and difficult to t urn, the
bo lts must be rep laced befo re checking
the to rque.
- Unti l the tig hte ning torque is checked,
d rive at redu ced speeds as a precaution .
Notes on wheel change
Please read the information ¢ page 193, New
tires and replacing tires and wheels ,
if you are
going to use a spare t ire which is different
from the tires on you r veh icle.
Afte r you change a tire :
- Check the tire pressure on the spare imme­
diately after mounting.
- Have the wheel bolt t ightening torque
chec ked w ith a torq ue wrench as soon as
poss ib le by your author ized A udi dealer or a
qualified service sta tion .
1) You need t he appro pria te adapte r to t ig hte n th e an ti­
t h eft whee l bolt s
c:> page 206 .
What do I do now? 209
- With stee l and alloy wheel rims, the whee l
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice while changing a tire that the
wheel bo lts are corroded and difficu lt to
turn, then they shou ld be rep laced before
you check the tightening torque.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible . Remount the wheel cover.
Until then , d riv e with e xtra care and at re­
duced speeds.
A WARNING
- If you are going to equ ip your vehicle
with tires or rims which differ from those
which were facto ry installed, then be
sure to read the information ¢
page 193,
New tires and replacing tir es and
wheels.
- Always sto re the tools secu rely in lug­
gage compartment. Othe rwise, in a n ac­
cident o r su dden maneuver they cou ld fly
forwdrd, CciU5ing injury to pd55enger5 in
the vehicle.
(D Note
Do not use comme rcially avai lab le tire
sea lants . Otherwise, the e le ctr ic al compo­
nen ts of t he tire p ressu re monitoring sys­
tem * wi ll no longe r work proper ly and the
sensor fo r the tire pressure mon itor ing
system will have to be rep laced by a quali­
fied workshop.
Jump-starting
General
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engi ne should fail to start because of a
discharged or weak battery, the battery can be
II>
•
•

Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through.
Fig. 163 Passenger's s ide wheel well: Foot rest w ith
fuse arrangement
The fuses are located in the footwell area on
the passenger's side behind a cover.
• Turn off the ignition and the affected e lec­
trical consumers .
• Check the following table to see which fuse
belongs to the consumer.
• Remove the floor mat .
• Fold the foot rest back
¢ fig. 163.
• Remove the clamp from the holder in the
fuse box.
• Remove the fuse using the clamp and re­
place the blown fuse w ith an identical new
one.
• Fo ld the foot rest down again .
A WARNING
Do not repair fuses and never replace a
blown fuse with one that has a higher amp
rating. This can cause damage to the elec­
trical system and a fire.
(D Note
If a new fuse burns out again after shortly
have you have installed it, have the electri­
cal system checked by your authorized Au­
d i dealer.
Fu se s and bulb s 213
@ Tips
-The following table does not list fuse lo­
cations that are not used.
- Some of the equipment items listed are
optional or only available on certain
mode l configurations.
Fuse assignment
Fig. 164 Passenge r footwell: Fuse assignment
Fuse panel @
Con sumer
1 VOA interface
2
3
4
5
Heated windshield washer
nozzle
Parking system
Engine compartment lid re­
lease
Diagnostic interface, light
switch, indicator light
Pa s­
se nger Air Ba g OF F,
selector
lever
6 Networking gateway
Amp s
5
5
5
10
10
5

220 Consumer Inf ormation
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Als o, sa fe ty a nd en vir onm ent al con­
cerns place very strict limits on the nature of
repairs and adjustments to engine and trans­
miss ion parts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment available to specially trained
workshop personnel in order to assure proper pe rformance, reliab ility and safety of the vehi­
cle and its many systems.
Improper maintenance, adjustments and re­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­
ranty. Therefore, proof of servic ing in accord­
ance w ith the ma intenance schedule may be a
condition for upholding a poss ible warranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any se rv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop.
We strong ly urge you to give yo ur autho rized
Audi dealer the opportunity to perfo rm all
schedu led maintenance and necessary repairs.
Your dea ler has the facilities, original parts
and trained specialists to keep your vehicle
running properly.
Performing limit ed m aint enance yours elf
The following pages describe a limited num­
ber of proced ures which can be performed on
your vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given . Always rigorously obse rve the
WARNINGS p rovided.
Before you ch eck anything in th e eng ine
co mpartm ent , alway s re ad and h eed all
WA RNINGS
c::> .&. and c::> ..&. in Working in the
engine compartment on page 169.
A WARNING
- Serious personal injury may occur as a re­
sult of improperly performed mainte­
nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r is k personal
injury.
- Do not attempt any of the maintenance,
checks or repairs descr ibed on the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re ­
spect to the vehicle, or are uncertain how
to proceed .
- Do not do any work without the proper
too ls and equipment. Have the necessa ry
work done by your author ized A udi deal­
er or another proper ly equipped and
qualified workshop.
- Always remove the ignition key before
anyone gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work under­
neath the vehicle. The jack* is not ade­
quate for this purpose and cou ld collapse
causing ser ious personal inju ry.
- If you must work underneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on level ground,
that the wheels a re a lways secure ly
b locked and that t he engine cannot be
s tarted.
- Always make sure the transmission se­
lec to r l ever is in
"N" (Neut ral) (R t ron ic)
or Neutral (manual transmission) and
the hand bra ke is f irmly app lied.
@ For the sake of the environment
- Changing the engine sett ings will ad­
verse ly affect emission leve ls. Th is is det­
r imental to the environment and increas­
es fuel consumpt ion .
- Always observe environmenta l regu la­
tions when disposing of old eng ine oil,
used brake flu id, dirty engine coo lant,
spent batteries or worn out tires.

A
A/C operation . . . . . . . . . . . . . . . . . . . . . . . 68
Accessories .. ... .. .. ...... .. .. .. .. . 221
Active ro llover protection system . . . . . . . 99
Retract ing ro llover protection . .. .. .. .. 99
Add ing
Engine coolant . ....... ... .. .. .. ... 177
Engine oi l .. .. ... ..... ... .. .. .. ... 174
Addit io nal accesso ries ...... .. .. .. .. . 22 1
Addit ives . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4
Ad justab le steer ing column . ... .. .. .... 70
Adj usti ng front seats ....... .. .. .. .. .. 59
Advanced Airbag System Ch ildren . .. ............. .... .. .. . 131
Components .. ........... .. .. .. ... 116
Front airbags . . . . . . . . . . . . . . . . . . . . . 114
H ow the components work together . . 117
M oni toring . ................ ... ... 120
Weight-se nsing mat ...... .. .. .. .. . 13 1
Airbag War ning/ indicator lights . .. .. .. .. .. .. 14
Airbag system . . . . . . . . . . . . . . . . . 109, 128
Care ... .. .. .. .... .. .... ... .. .. ... 122
Child restra ints ........... .... .. ... 132
Components (front airbags) .. .. .. .. . 116
Danger of fitting a child safety seat on
the front passenger seat . . . . . . . . . . . . 11 1
Disposal . ................ ... ... .. 122
Fr ont airbags ............ .... .. ... 1 13
H ow do the front a irbags work? . .. .. . 118
H ow many airbags does my vehicle
have? ... .. .. .... .. .... ... .. .. ... 116
Important safety instructions on the
knee airbag system ....... .. .. .. .. . 126
Important things to know . . . . . . . . . . . 109
Indicator light ........... .. .. .. ... 120
Knee airbags . . . . . . . . . . . . . . . . . . . . . . 124
Mo nitor ing . ................ ... ... 120
P ASSENGER AIR BAG OFF l ight .. ... .. 120
Service . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2
Side airbags .. ........... .. .. .. ... 12 7
When mus t the system be inspected? . 120
Ai r cond itioni ng
A/C operation . . . . . . . . . . . . . . . . . . . . . . 68
A ir dist ribution ........... .. .. .. .... 67
A ir r eci rcula tion mode ..... .. .. .. .. .. 68
Automatic mode . . . . . . . . . . . . . . . . . . . 68
Inde x 223
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Defrost ... .. .. .... . ... ...... ... .. . 68
Econom ica l use . ... . .. ..... ... .. .. . 69
Fan ........ .. .. .................. 67
Rear window defogger . ............. . 69
Switching on and off ................ 67
T emperature ... .. .. . .. .... .... .. .. . 66
Air distribution . . . . . . . . . . . . . . . . . . . . . . 67
A ir recircu lation mode
Air condi tioning . . . . . . . . . . . . . . . . . . . . 68
All -wheel drive .. .. .. ..... .......... 147
Winter tires . . . . . . . . . . . . . . . . . . . . . . 197
A lternator
refer to Generator . . . . . . . . . . . . . . . . . . 14
Anti-freeze
refer to Engine coolan t sys tem ... .. .. 175
Anti- lock b rake system
Warning/ind icator lights .......... .. . 16
Anti- lock braking system ......... .... 142
Anti -slip reg ulation . .. ... .... ... .. .. 142
Anti-theft ala rm system ......... .... .. 38
Anti-theft whee l bolts ........... .... 206
Ashtray .. .. .. .. .. .... ........... .. . 62
Asterisk ...... .. .... .. ........ ...... . 5
Audi magnet ic r ide . . . . . . . . . . . . . . . 19, 75
Description . ... .... . ... ...... ... .. . 75
Ind icator light . .. ................. . 19
Audi Se rv ice Repair Manuals and Lit era-
ture .. ... .. .. .... ... .. .. ..... ... .. 219
Automated manual t ransmission
refer to R tronic . . . . . . . . . . . . . . . . . . . . 78
Automat ic be lt retractor ......... .. .. 104
A utomat ic car wash
refer to Washing . . . . . . . . . . . . . . . . . . 153
Automat ic head light . .............. .. 49
Auto Safety Hot line .................. 97
Ave rage fuel mileage . . . . . . . . . . . . . . . . . 24
Average speed . . . . . . . . . . . . . . . . . . . . . . . 24
B
Battery .... .. .. .. .. .. ........... .. 178
Charg ing .. .... .. ................. 180
Checking . . . . . . . . . . . . . . . . . . . . . . . . . 178
Disconnecting ... .. . .. .... .... .. .. 178
Low .... .. .. .. .. .. ............... 14 7
replacing .. .. .. .. .... ............. 181
•
•