brake AUDI R8 SPYDER 2014 Workshop Manual

216 What do I do now?
Removing the wheel
.. Use the hexagonal socket in the screwdriv­
er handle
to comp letely turn out the top­
most wheel bolt and set it aside on a
clean
sur face .
.. Screw the threaded end of the
alignment
pin
from the tool kit hand-tight into the
now vacant bolt hole
o fig. 162.
.. Then completely unscrew the other wheel
bolts as described above .
.. Take off the wheel leav ing the alignment pin
in the bolt hole
o(D .
Putting on the wheel
.. Lift the spare wheel and carefully slide it
over the alignment pin to guide it in place
o@.
.. Use the hexagonal socket in the screwdr iver
handle to screw in and tighten all wheel
bolts
slightly .
.. Unscrew the alignment pin and insert and
tighten the remaining whee l bolt slig htly
like the rest.
.. Turn the jack handle counter-clockw ise to
lower the vehicle until the jack is fully re­
leased .
The wheel bolts must be clean and turn easily.
Check the contact surfaces of wheel and hub. Remove contaminants on these surfaces be­
fore installing the wheel.
The hexagonal socket in the screwdriver han ­
dle makes it easier to handle the wheel bolts.
The reversible blade should be removed.
When mounting
unidirectional tires, observe
the direction of rotation
o page 214.
«I) Note
When removing or installing the wheel,
the rim could hit the brake rotor/ceramic
brake rotor* and damage the rotor. Work
carefully an have a second perso n he lp
you .
1l You need the appropriate adapte r to tigh ten the anti­
theft whee l bo lts
c:> page 214.
(D Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bo lts.
Tightening wheel bolts
.. Fit the wheel bolt wrench over the wheel
bolt and push it down as far as it will go
ll.
.. Close your grip around the end of the
w rench handle for maximum torque and
turn each wheel bolt
clockwise until it sits
tight .
Have the
tightening torque of the wheel bolts
checked as soon as possible with a to rque
wrench. It should be 120 Nm .
Check the
tire pressure as soon as possible.
Return the veh icle tool k it to its proper place.
A WARNING ..,___
Loosening the wheel bolts is prohibited;
danger of an acc ident!
(D Tips
- Never try and use the hexagonal socket
in the handle of the screwdriver to loos­
en or t ighten the wheel bo lts.
- If you have determined that wheel bolts are corroded and difficult to turn, the
bolts must be replaced before check ing
the torque .
- Until the t ightening torque is checked,
dr ive at reduced speeds as a precaution.
Notes on wheel change
-
Please read the information o page 199, New
tires and replacing tires and wheels,
if you are
go ing to use a spa re tire wh ich is different
from the tires on your vehicle.
After you change a tire:

4. Secure the other end to the jump start pin
© for the discharged battery@.
Starting the engine
.,. Start the eng ine of the vehicle providing as­
s istance and allow it to run at id le.
.,. Now start the engine of the vehicle with the
discharged battery .
.,. If the engine does not start: Stop trying af­
ter 10 seconds and then try again after
about 30 seconds .
.,. Disconnect the cable while the engine is
running in exactly
reverse order to that de­
scribed.
The battery is vented to the outside to prevent
gases from entering the vehicle interior. Make
sure that the jumper clamps are well connect­
ed with their
metal ports in full contact with
the battery termina ls.
A WARNING
To avoid serious personal i njury and dam­
age to the vehicle, heed all warnings and
instructions of the jumper cable manufac­
turer.
If in doubt, ca ll for road service .
- Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the engine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c:> page 172, Working in the
engine comportment.
Improper hook-up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
ce lls are screwed in firmly. If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
-
What do I do now? 219
- Please note that the procedure for con ­
necting a jumper cable as described
above applies specifically to the case of
your vehicle being jump started. When
you are giving a jump start to another ve­
hicle, do
not connect the negative(-) ca­
ble to the negative(-) terminal on the
discharged battery@. Instead, securely
connect the negative(-) cable to eithe r a
solid metal component that is firmly
bolted to the engine block or to the en­
gine block itself. If the battery that is be­
ing charged does not vent to the outside,
escaping battery gas could ignite and ex­
plode!
Emergency towing
with commercial tow
truck
' General hints
Your Audi requires special handling for tow­
ing.
The following information is to be used by commercial tow truck operators who know
how to operate their equipment safely.
- Never tow your Audi, towing will cause dam­
age to the engine and transmission.
- Never wrap the safety chains or winch cables around the brake lines.
- To prevent unnecessary damage, your Audi
must be transported w ith a car carrier (flat
bed truck) .
- To load the vehicle on to the flat bed, use
the towing loop found in the vehicle tools
and attach to the front anchorage
c:> page 220 .
A WARNING
A vehicle being towed is not safe for pas­
sengers . Never allow anyone to ride in a
vehicle be ing towed, for any reason.
•
•

222 Fuses and bulbs
Fuse panel @
Consumer Amps
Automatically dimming in-
side mirror, garage door
8 opener (Homel
ink), washer
10
pump relay, power outlets
relay
10
[ru button 10
11 Pressure sensor, climate
5
controls
12 Airbag 5
Fuse panel@
No . II Consumer
II Amps
1 Radiator fan (1)
40
2 Radia
tor fan (2)
40
3 Exterior lighting
40
4 Exterior lighting 40
6 Blower regulator 40
Fuse panel@
No . II Consumer
II Amps
1 Rear view camera
5
2
Tire pressure monitoring
system 10
4 Cell phone package, te
le-
7.5
phone antenna amplifier
5 Instrument cluster 5
6 Networking gateway
5
7 Steering column lever 5
8 Diagnostic interface, brake
10
pedal switch, selector lever
9 Rain/light sensor 5
10 Light switch 5
11 Special functions control
5
module
15 Sound amplifier 30
Radio 20
Fuse panel E
No. Consumer Amps
3 Auxiliary water pump 10
5 Supply terminal 15, starter 30
Fuse panel @
No. Consumer Amps
6 Pump for brake booster 15
7 Horn
20
8 Wiper motor 30
9 Wiper motor
30
10 Headlight washer system 30
12 Power outlets and cigarette
20
lighter
Fuse panel ®
No. !!Consumer
ll Amps ,
1 E
lectronic Stabilization Pro -
10
gram
2 Electronic
Stabilization Pro-
25
gram
3 Partition window
defogger
15
Rear window defogger/RB
4 Spyder: Rear window defog- 30/20
ger
5 Power lock
ing system 20
6
Interior Lights, washer noz-20
zles
7 Anti-theft alarm system 5
8 Climate controls 10
9 Heated seats 25
10 Lumbar support 10
11 Control module for doors 30
12 Control module for doors
10
Bulbs
Note
Your vehicle is equipped with maintenance­
free headlights and rear lights. However, if a
bulb has to be changed, please consult your
authorized Audi dealer or other qualified
workshop.

228 Con sum er Inf ormation
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Als o, sa fe ty a nd en vir onm ent al con­
cerns place very strict limits on the nature of
repairs and adjustments to engine and trans­
miss ion parts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment available to specially trained
workshop personnel in order to assure proper pe rformance, reliab ility and safety of the vehi­
cle and its many systems.
Improper maintenance, adjustments and re­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­
ranty. Therefore, proof of servic ing in accord­
ance w ith the ma intenance schedule may be a
condition for upholding a poss ible warranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any se rv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop.
We strong ly urge you to give yo ur autho rized
Audi dealer the opportunity to perfo rm all
schedu led maintenance and necessary repairs.
Your dea ler has the facilities, original parts
and trained specialists to keep your vehicle
running properly.
Performing limit ed m aint enance yours elf
The following pages describe a limited num­
ber of proced ures which can be performed on
your vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given . Always rigorously observe the
WARNINGS p rovided.
Before you ch eck anything in th e eng ine
co mpartm ent , alway s re ad and h eed all
WA RNINGS
c::> .&. and c::> ..&. in Working in the
engine compartment on page 173.
A WARNING
- Serious personal injury may occur as a re­
sult of improperly performed mainte­
nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r is k personal
injury.
- Do not attempt any of the maintenance,
checks or repairs descr ibed on the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re ­
spect to the vehicle, or are uncertain how
to proceed .
- Do not do any work without the proper
too ls and equipment. Have the necessa ry
work done by your authorized A udi deal­
er or another proper ly equipped and
qualified workshop.
- Always remove the ignition key before
anyone gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work under­
neath the vehicle. The jack* is not ade­
quate for this purpose and cou ld collapse
causing ser ious personal inju ry.
- If you must work underneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on level ground,
that the wheels a re a lways secure ly
b locked and that t he engine cannot be
started.
- Always make sure the transmission se­
lec to r l ever is in
"N" (Neut ral) (R t ron ic)
or Neutral (manual transmission) and
the hand bra ke is f irmly app lied.
@ For the sake of the environment
- Changing the engine sett ings will ad­
verse ly affect emission leve ls. Th is is det­
r imental to the environment and increas­
es fuel consumpt ion .
- Always observe environmenta l regu la­
tions when disposing of old eng ine oil,
used brake flu id, dirty engine coo lant,
spent batteries or worn out tires.

232 Index
B
Battery .......... ......... ... .... .
Charging ... .. .............. ..... .
Connecting ................. ..... .
Disconnecting ............... .... .
Important warnings ...... .... .... .
Location
. ...... .... ..... .... .. .. .
184
187
184
184
185
185
Low ..... .. ............ ... .. .. ... 150
Replacing the battery ...... ... .. .. . 185
State of charge ........... .. .. .. .. . 150
W inter operation ......... .. .. .... . 184
Working on the battery .. .. .. .. .. .. . 185
Battery voltage . . . . . . . . . . . . . . . . . . . . . . 18
Before driving . . . . . . . . . . . . . . . . . . . . . . . 93
Blended gasoline
Booster seats
Brake system 167
139
Anti-lock brake system ..... ... .... .. 16
Brake assist system ........ ... .... .
Brake fluid
.................. .....
144
183
Brake light defective . . . . . . . . . . . . . . . . 18
General information ...... .. .. .. .. . 146
How does the moisture or road salt affect
the brakes? ... .. ...... .... ... .. .. . 146
Malfunction ............. .... ...... 13
Warn ing/ indicator lights ....... .. .. . . 13
Worn brake pads symbol . . . . . . . . . . . . . 17
Break -in period . .......... ... .. .. ... 153
Bulbs .. ... .................. ..... . 222
C
California Proposition 65 Warning . ... . 173
Battery specific . . . . . . . . . . . . . . . . . . . 186
Capac it ies . ................. .. .. .. . 225
Carbon-fiber parts Exterior · · ............... .. .. .. .. . 160
Inter ior .. .. ... .... ...... ... ... .. . 162
Car care ..... ................ ..... . 156
Inter ior ...... ........... .. .. .... . 161
Cargo area
refer to Luggage compartment . . . . . . . . 98
Catalytic converter ........ ... .. .. .. . 153
Certification ................. ..... . 230
Changing a flat tire ....... .. .. .. .. .. . 214
Chassis
refer to Audi magnetic ride ... .. .. .. . . 75 Checking
Engine coolant level
................
Tire pressure ... .. ................ .
Child restraint
Danger of using child restraints in the
front seat
. .... .. ................ .
Child restraints
Where can I get additional informat ion
about child restraints and the ir use? ..
Child safety . .... .. ... .......... ... .
Convertible locking retractor . .. .. .. . .
Important safety instructions for using
child safety seats . ... .......... .. . .
Important things to know when driving
with children
................. ....
Child safety seat . .. ... ......... ... . .
Convertible locking retractor .. ... .. . .
Installing . .. .. .. .... .... ..... .. . .
Child safety seats Booster seats
................. ....
Convertible child seats .......... ...
How do I properly install a child safety
seat in my veh icle? ...... ....... .. . .
Infant seats
......... ' . ' . ' ' . ' .....
182
195
112
143
132
140
135
132
137
140
140
139
138
135
137
Safety instructions ... .......... .. .. 135
Cigarette lighter . . . . . . . . . . . . . . . . . . . . . 60
Cleaning Alcantara (synthetic suede) .......... 164
Engine compartment . . . . . . . . . . . . . . . 165
Exhaust tail pipes .................. 161
Fabrics and fabric coverings .. ... .. .. 162
Interior ....... .. ..... ..... ... .. .. 161
Leather . .. ... ... ... ......... ... .. 164
Matte finish paint ............. .... 158
Nav igat ion d isplay ............... .. 161
Radio display .... ................ . 161
Safety belts ... .. ................ . 165
Cleaning and protect ion . ...... ... .. . .
Climate controls
.....................
156
63
Dust filter . . . . . . . . . . . . . . . . . . . . . . . . . 63
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Pollen filter . . . . . . . . . . . . . . . . . . . . . . . 63
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . 63
Clock
............................... 9
Closing
Engine compartment lid ......... ... 17 4
Cold tire inflation pressure ..... ... .. .. 193

Tire pressure monitoring system .... .. . 206
Malfunctions .... ..... ... ... ... ... 208
Sensors . ... .... ........ ... .. .. .. . 201
Tires and whee ls ......... .. .. .. .. . 201
Valves ... .. ................. .. ... 201
Warn ing/ indicator light ....... .. .... . 19
Tire repair kit . ..... .... ... .. .. .. ... 210
T ires .. .. .. .. .... ............. .. .. . 189
P ressu re . .. .. ........... .. .. .. ... 206
Replacing . . . . . . . . . . . . . . . . . . . 199, 201
Service life ..... ...... ... .. .. .. ... 198
Speed rating letter code ... .. .. .. .. . 200
T ire manufacturing date ... .. .. .. .. . 200
Tire pressure monitoring system .. .. . 206
Tire specifications ........ .. .. .. .. . 200
T read depth . . . . . . . . . . . . . . . . . . . . . . 198
Uniform t ire quality grading .. .. ... .. 203
W inte r tires ................ ... ... 203
T ires/Wheels
Low aspect ratio tires ...... .. .. .. .. . 205
T ire mobility system ...... .. .. .. .. . 210
Tire repa ir kit ......... ...... .... .. 210
Tires and vehicle load limits . ... .. .. .. . 196
Tires and whee ls
C heck in g tire p ressu re ..... .. .. .. .. . 19S
Cold ti re inflation pressu re ... .. .. ... 193
D imensions ... .... .... ... .. .. .. .. .
General notes ... .. .... ... .. .. .. .. .
Glossary of t ire and load ing termino lo-
gy .. .. ' . .. ................. .. .. .
New tires and wheels ...... .. .. .. .. .
Replacing .. ................ ... .. . 199
189
190
199
200
Snow chai ns ... .. .. ...... .. .. .. .. . 204
T ire pressure monitor ing system .. .. . 20 1
Tires and vehicle load limits .. .. .. .. . 196
Wheel bol ts ............. .... .. .. . 205
W inter t ires . .... ..... ... .. .. .. ... 203
Tire serv ice life .... .. ...... .. .. .. .. . 198
T ool kit ... .. .. .. ........... .. .. ... 210
Touch -up paint ............ .... .. .. . 160
T owing
Tow truck procedures ........... .... 219
Towing loop .. .... .. .... ... .. .. .. ... 220
T railer towing ............. .. .. .. .. . 155
Transm ission
Manual transmission .......... ... ... 77
Transm ission ma lf u nct ion (indicator light) 81
Inde x 239
Transpor t Canada ..... .. .. ..... ... .. 100
Tread Wea r Ind icator (TWI) ........... 198
Tr ip comp uter . .. .. ............... .. . 21
S ingle-trip memory ............ .... . 21
Tota l-trip memory .. . ... .... ... .. .. . 21
T rip odometer ..... .. . .. .. ..... ... .. . 10
Turn signals . .. .. .... ... ....... ...... 47
Warning/ind icator lights ........ .... . 19
u
Un fastening safety belts 108
Un idirectional tires . ............. .... 189
Un iform tire qua lity gradi ng ...... .. .. 203
U ni versal Radio- Frequency Remote Con-
trol (Homelink ®) . . . . . . . . . . . . . . . . . . . . 90
U nl ocking
Power locking system .............. . 32
Remote contro l key . . . . . . . . . . . . . . . . . 31
V
Vanity mirro r .. .. .. .. .. .. .. .... ... .. . 51
Vehicle-ca re p roducts ............ .... 156
Vehicle electrical system . . . . . . . . . . . . . . 14
Vehicle Identification Number (V IN) . ... 223
Vehicle jac k .... ... .. ............... 214
Vehicle literature .. ................. .. 4
Vehicle sh ut-down . ............. .. .. 154
Vehicle tool kit .. ... ............... . 210
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . 63
Voltmete r display . . . . . . . . . . . . . . . . . . . . 11
w
Warning/ind icator lights . . . . . . . . . . . . . . . 8
Airbag syst em . . . . . . . . . . . . . . . . . . . . . 14
An ti- lock b rake sys tem (ABS) .... .. .. . 16
Br ake system . . . . . . . . . . . . . . . . . . . . . . 13
Cruise cont ro l .... .. . .. .. ..... ... .. . 19
E lectronic power contro l . . . . . . . . . . . . . 17
E lectronic Stabilization Contro l (ESC) . .. 15
Generator . . . . . . . . . . . . . . . . . . . . . . . . . 14
Malfunction Ind icator Lamp (MIL) .. .. . 17
Parking brake .. .. .. . ....... ..... .. . 13
Safety be lt . . . . . . . . . . . . . . . . . . . . . . . . 14
Safety systems . . . . . . . . . . . . . . . . . . . . . 14
•
•