brake light AUDI RS5 CABRIOLET 2015 Owner's Manual

M N
a! u.. co ,...., \!) ..,.,
,...., ..,., ,....,
@ Tips
Your vehicle may be equipped with Audi
connect. Your use of certain Aud i connect
features req uires wireless serv ices that are
provided by a third party wireless telecom­
municat ions provider. For details regard­
ing how information obtained through
Aud i connect is collected, processed,
transmitted, used, and shared, please see
your contra ct w ith the wire less telecom ­
municat ions provider and the "About A udi
connect" tab in your vehicle's MMI*:
!MENU ! button> Audi connect > About
Audi con nect .
Electronic Stabilization
Control (ESC)
Description
ESC helps to improve road holding and vehicle
dynamics to help reduce the probability of
skidd ing and loss of veh icle control. It works
only when the eng ine is running. ESC detects
certain difficult driv ing situations, including
when the vehicle is beginning to spin (yaw) out of cont ro l and he lps you to get the vehicle
back under control by select ively b rak ing the
wheels, and/or red ucing engine power and
p roviding steering assistance to help hold the
ve hicle on the driver's intended course . The in­
dicator light
DJ in the instrument cluster
blinks when ESC is taking action to help you
control the vehicle.
ESC has limitations.
It is important to remem­
ber that ESC cannot overcome the laws of
phys ics. It will not a lways be able to help out
under all conditions you may come up against.
For example, ESC may not always be able to
help you master situat ions where there is a
sudden change in the coefficient of fr iction of
the road surface. When there is a sect io n of
d ry road that is s udden ly cove red with water,
slush o r snow, ESC canno t perform the same
way it would on the dry su rface.
If the vehicle
hydroplanes (rides on a c ush ion of water in­
stead of the road surface), ESC wi ll not be
ab le to he lp you steer the veh icle because con-
Int ellig ent technolog y 171
tact with the pavement has been interrupted
and the vehicle cannot be braked or steered .
D uring fast corner ing, particular ly on wind ing
roads, ESC cannot always deal as effectively
with difficult dr iv ing s ituations than at lower
speeds. When towing a trailer, ESC is not able
to help you regain control as it would if you
were not tow ing a trailer.
Always adjust your speed and driving style to road, traffic and weather conditions . ESC can­
not override the vehicle's physical lim its, in­
crease the availab le tract ion, or keep a veh icle
o n the road if road departu re is a result of
driver ina ttent io n. Instead , ESC imp roves the
poss ibility of keep ing the vehicle under con­
trol and on the road during extreme maneu­
vers by using the driver's steering i nputs to
help keep the vehicle go ing in the intended di­
rect ion. If you are traveling at a speed that
causes you to run off the road before ESC can
provide any assistance, you may not experi­
ence the benefits of ESC.
ESC is switched on all the time. In certain sit­
uat ions when you need less traction, you can
switch off ASR by pressing the butto n
[ill
~ page 173, fig. 166 or~ page 173,
fig. 167. Be sure to sw itch ASR on aga in when
you no lo nger need less traction.
The following systems are integrated in the
ESC:
Anti-lock bra king sy stem (ABS )
ABS prevents the whee ls from locking up
when brak ing. T he vehicle can st ill be steered
even dur ing hard braking. App ly steady pres­
su re to the brake peda l. Do not pump the ped­
al. A pulsing in the brake pedal ind icates that
the system is helping you to brake the veh icle .
Brake assi st system
The brake ass ist system can decrease braking
distance. It increases brak ing power when the
drive r presses the brake peda l quickly in emer­
gency s ituations. You must press and hold the
brake pedal unti l the s ituation is over. In
vehicles with adaptive c ruise control*, the
brake assis t system is more sensitive if the
•
•

172 Intelligent technology
distance detected to the vehicle ahead is too
smal l.
Anti-slip regulation (ASR )
ASR reduces eng ine power when the drive
wheels begin to spin and adapts the fo rce to
the road condit ions. This makes it eas ier to
start, accelerate and drive up hills .
Electronic differential lock (EDL )
The EDL brakes wheels that are spinn ing and
transfers the d rive powe r to the other wheels.
This f unct ion is available up to abo ut 60 mph
(100 km/h) .
In extreme cases, ED L automat ica lly switches
off to help keep the brake on the braked whee l
from ove rheating. EDL wi ll switch on aga in a u­
tomatically when conditions have returned to
norma l.
Steering recommendation
The ESC helps to stabilize the ve hicle by
changing the steering to rque.
In vehicles with dynam ic steeri ng*, ESC also
helps to stabilize the stee ring in critical s itua­
tions.
Select ive wheel torque control
Selective whee l torque control is used when
driving on curves . The front wheel on the in­
side of the curve or both wheels on the inside
of the curve are braked selective ly as needed.
This a llows mo re prec ise d riving in curves. The
appl icable system may no t activate when d riv­
i ng in wet or snowy condi tions.
A WARNING
- The ESC and its integrated systems can ­
not overcome the laws of physics. This is especia
lly important on slippery o r wet
roads. If the systems begin acting to sta­
bilize your veh icle, you should immedi­
ately change your speed to match the
road and traffic cond itions. Do not let
the increased safety provided by these
systems tempt you to take risks. Do ing
so will in crease the r is k of a loss of vehi­
cle control, collision and serious person al
in juries.
- Always adap t your speed to road, traffi c
and weather conditions . The risk of los ­
ing control of the vehicle increases when
driving too fast, especially through
curves and on slippery or wet roads, and
when dr iv ing too close to vehicles up
ahead. The ESC and its integrated sys­
tems cannot a lways p revent collisions -
there is still a risk of acc idents!
- Always accelerate with special care on
even, smooth s urfaces such as those that
are wet or covered with ice and snow.
T he drive w heels can spin even w ith
these assistance sys tems that cannot al­
ways he lp to re duce the risk of loss of ve ­
h icle control.
(D Tips
- ABS and ASR o nly wo rk correctly when
a ll four wheels are equipped wi th iden ti­
c al tires. D ifferen t tire sizes can lead to a
reduction in engine powe r.
- Yo u may hear noises when the systems
descr ibed are workin g.
-If the ind icator light DJ or Ea (USA
mode ls)/ lCOj t here may be a malfunction
~ page 18,
<=>page 19.

174 Intelligent technology
Braking
What affects braking efficiency?
New brake pad s
Du ring the first 2 50 miles (400 k m), new
b ra ke pads do not possess their fu ll braking
effect , they have to be "broken in" first¢.&. .
The break-in period can be considerably lon­
ger for vehicles with ceramic brake rotors*.
You can compensate for this slightly reduced br aking power by push ing harder on the brake
pedal. Avoid heavy braking loads during the
b reak-in per iod.
Operating conditions and d riving h abits
The brakes on today's automobi les are st ill
subject to wear, depend ing largely on operat­
ing conditions and dr iv ing habits ¢.&. . On
vehicles that are e ithe r dr iven mostly in stop­
and-go city traffic o r are driven ha rd, the
b rake pads should be checked by you r aut hor­
iz ed A udi de aler more often than specified in
the
Warrant y & Maintenan ce booklet . Fail ure
to have your b ra ke pads inspected can resu lt
in red uced brake performance.
On steep slopes, yo u sh ou ld use t he b ra ki ng
effect of the eng ine. Th is w ay, you preven t un­
necessa ry wear on the brake system . If you
must use yo ur brakes, do not ho ld the brakes
down continuously. P ump the brakes at inter ­
va ls.
Operating noise
N oises may occur when braking depending on
the speed, braking fo rce and outside condi­
tions s uch as temperature a nd h umidity.
Due to the na ture of the mate rials used i n ce­
ramic brake rotors*, noises may become more
apparent at low speeds.
Effect of water and road salt
I n ce rtain situat ions, for exampl e after d riving
throug h wate r, in heavy ra in, after overn igh t
conde nsation or afte r washi ng your c ar, the
b ra ki ng effect can be reduced by moisture or
ice on the bra ke rotors and b rake pads. The brakes must be dr
ied first with a few careful
brake applications .
At highe r speeds and with the winds hield wip­
ers t urned on, the b ra ke pads press against
the b rake roto rs fo r a short amount o f time .
This occurs at regular intervals without the drive r not icing and p rov ides for better brake
response time under wet conditions.
The effectiveness of the brakes can be red uced
whe n the vehicle is driven on a sa lt -covered
road and the brakes are not used . Likewise,
you clean off accumulated salt coating from brake d iscs and pads with a few cautious ap­
plicat ions of the bra ke
¢ .&. .
D ue to the ir s urface characteristics, ceramic
brake rotors* absorb moisture in such condi­
tions . T his can cause a temporary reduction in
braking force compared to dry brakes . You can
compensate for th is by pressi ng the brake
p eda l harde r.
Corrosion
There may be a tende ncy for dirt to build up
on the brake pads and corros ion to form on
the d iscs if the car is not driven regu larly or
only for short trips w it h litt le use of the
brakes .
If the brakes are not used frequently, or if cor­
ros io n has formed on the discs, it is adv isable
to clean off the pads and discs by braking
firmly a few times from a moderately h igh
speed ¢.&. .
Faults in the brake system
If you shou ld notice a sudden increase in
brake pedal trave l, then one of the two brake
c ir cuits may have fa iled
c::> .&. .
Low brake fluid level
Malfunctions can occur in the brake system if
t h e brake fluid level is too low. The brake flu id
level is monitored electro nically .
Brake boo ster
The brake booster increases the pressure that
yo u generate with the brake peda l. It works
on ly when the engine is running
. ¢ .&. .,.

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
Brake lining w ear sta tus
Brake lining we ar may be che cked by visual in­
spection of the condition of the brake pads
through the openings in the whee l. If neces ­
sary, the wheel may be remove d for this in­
spection
c> page 244, Changing a wheel.
.&_ WARNING
- New brake pads do n't have the best sto p­
ping power and must be "broken-in" dur­
ing the init ial 100 to 1 50 m iles (150 to
200 k ilometers) of normal city driving.
T he break-in period can be considerably
longer for veh icles with ceram ic br ake ro­
tors*. You can compensate for this by pressing the brake pedal more firmly.
T his also applies later when new pads are
installed .
- You should perform braking maneuvers
for the purpose of cleaning the brake
system on ly if road condit ions permit.
Other road users must not be put at r isk -
you may cause an acc ident!
- Before descending a steep grade, reduce
speed and shift transmiss ion into a lower
gear or lower driving range. Do not ride
the brakes or hold the pedal down too
long or too ofte n. This cou ld cause the
brakes to get hot and d imin ish b raking
efficiency.
- Do not "r ide the brakes" by resting your
foot on the pedal when you do not inte nd
t o brake. Th is may cause the b rakes to
overheat, prema ture wear and inc reased
stopping distance .
- Under certa in climat ic and operating
conditions such as passing through wa ­
ter, driving in heavy rain or after wash ing
the vehicle, the effectiveness of the brakes can be reduced. In winter, ice can
accumulate on the brake pads, linings,
discs and drums. Carefully apply brakes
for a test. Brakes will dry and ice coat­ ings will be cleaned off after a few ca re­
ful brake applications.
- Driv ing fo r an extended pe riod of time on
salt-covered roads w ithout using you r
Intellig ent technolog y 175
brakes can a lso affect braking efficiency .
Clean off accum ulated salt coating from
brake discs and pads with a few careful
brake applications.
- If you damage the front spoiler, or if you
install a different spoiler , be sure the air
f low to the front brakes is not obstruct­
ed. Otherw ise the brake system could
overheat reducing t he effectiveness of
the entire brake system.
- Failure of one b rake circuit will impa ir
the braking capab ility result ing in an in­
creased s topping distance. Avoid driving
the vehicle and have it towed to the near­
est a utho rized Audi dea le r or q ualified
workshop.
- Never let the vehi cle roll to a stop with
the engine shut off.
- If the b ra ke booste r is no t working, the
brake peda l must be p ressed considera­
b ly harder to make up for the lack of
booster assistance .
Electro-mechanical
power assist, dynamic
steering
The electro-mechanical power assist helps
the driver when steering.
Power steer ing adapts electronically based on
t he ve hicl e speed.
Indicator lights and messages
• Steering defect ive! Do not drive vehicle!
If this indicator light turns on and stays on
and this message appears, the power steer ing
may have failed.
Do
not continue driving. See your authorized
Audi dealer or a qualified repair facility for as ­
s istance.
E!'Y D ynamic stee ring: System fault! You can
continue dri ving
If the indica tor ligh t turns on and the mes-
sage appears, the stee ring may be more diffi ­
cu lt to move o r more sensit ive than usual. The ..,.
•
•

180 Driving and en vironm ent
8_ WARNING
After driving through water, mud, slush,
etc ., the brakes may be slow to take effect
because of wet brake rotors and pads. Dry
the brakes first by braking carefully to re­
store the full braking effect.
(D Note
Vehicle components such as the engine,
transmiss ion, suspension or electrical sys­
tem can be severely damaged by driving
through wate r.
@ Tips
- Check the depth of the water before dr iv­
i ng through it.
- Do not stop the veh icle, dr ive in reverse
or switc h the engine off when driving
t hr ough water.
- Keep in mind that oncoming vehicles
may c reate waves that raise the water
l evel and make it too deep fo r you r vehi­
cle to dr ive through safely.
- Avoid dr iving thro ugh salt water because
i t can ca use corrosion.
Warming up and
cooling down
-
By carefully warming up and cooling down
your ve hicle, you can he lp ensure that it is not
overstressed unnecessarily dur ing sporty driv ­
ing.
When warming up, the vehicle is d riven at a
maximum engine speed of 6000 RPM in order
to raise the engine oi l temperature to a mini ­
mum of 140
°F (60 °(). The tires also only
reach their full road holding capability once
they have warmed up .
The cooling fan can contin ue to run in your ve­
h icle after the engine is switched off. Howev­
er, driving the vehicle to cool it down is part ic­
ularly important. During sporty driving, the
engine and brakes, the ex ha ust system, and
the transm ission all become extremely hot.
B efore you park the vehicle, you shou ld drive it for a few miles/kilometers at
light load in
the low rpm range to allow it to cool down.
Catalytic converter
It is very important that your emission con­
trol system (catalytic converter) is function­
ing properly to ensure that your vehicle is run­
ning in an environmentally sound manner.
.. Always use lead-free gasoline c:> page 190,
Fuel supply.
.. Never run the tank down all the way to emp­
ty .
.. Never put too much moto r oil in your engine
c:> page 199, 't::71 Adding engine oil .
.. Never try to p ush- or tow -sta rt yo ur vehicle.
The catalytic converter is an efficient "clean­
up" device bu ilt into the exhaust system of
t h e vehi cle. The cata lytic conve rter bu rns
many of the pollu tan ts i n t he exh aust gas be­
f ore they are re lease d into the atmosphere.
T he exclusive use of unleaded fue l is critica lly
impor tant for the life of the catalyt ic convert­
er and prope r fu nct ion ing of the engi ne.
8_ WARNING
- T he temperature of the exhaus t system
is high, both when driving and after stop ­
p ing the engine.
- Never touch the exhaus t tail pipes once
they have become hot . This cou ld result
in burns .
- Do not park or operate the vehicle i n
areas where the hot exha ust system may
come in contact with dry grass, brush,
fue l spill or other material wh ich can
cause a fire.
- Do not app ly additional undercoating or
rustproofing on or near the exhaust
manifold, exhaust pipes, catalytic con­
ver ter or heat shields . Dur ing driv ing, the
substance used for undercoating could
overheat and cause a fire.

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
(D Note
-Be aware that just one tank fi lling with
le ad ed fuel will already seriously de­
grade the performance of the catalytic
converter.
- Do not exceed the correct engine oil leve l
c>page 199.
-Do not drive until the fuel tank becomes
complete ly empty. The engine could mis ­
fire. Unburned fuel could also get into
the exhaust system and this could cause
the catalyt ic converter to overheat.
- Do not turn off the ignition while the ve­
hicle is moving .
- Do not continue to operate your vehicle
under these condit ions, as otherwise fuel
can reach the catalytic converter. This
could result in overheat ing of the con­
verter, requ iring its replacement.
- To assure efficient operat ion of the Emis­
s ion Control System:
- Have your vehicle maintained properly
and in accordance with the service rec­
ommendations in your Warranty
&
Ma intenance booklet.
- Lack of proper maintenance as well as
improper use of the vehicle will impa ir
the funct ion of the emission control
system and could lead to damage .
@) For the sake of the environment
Even when the Emission Control System is
operating properly, the exhaust gas can
have a sulfur-like exhaust gas smell under
some operating states. This depends on
the s ulfur content of the fuel being used.
Using a d ifferent brand of fuel may help,
or filling the tank w ith lead-free super
grade gasoline .
Shutting down vehicle
If you would like your veh icle to remain inop­
erat ive for a longer period of time, contact an
Audi or other specialized dealer. They can ad­
vise you on necessary precautions e .g. corro ­
sion prevention, maintenance and storage.
Dri vin g and en vironm ent 181
Pay attention to additional information con ­
cerning the battery . Refer to
c> page 205 .
Operate your vehicle
economically and
minimize pollution
General
Your personal style of driving will determine
the economy of your vehicle, as well as ex ­
haust and noise levels.
Fuel economy, environmenta l impact, and
wear on your engine, brakes and tires largely depend on three factors:
- your personal d riving style
- operating conditions
- technical limitat ions
If you ant ic ipate what you need to do next and
drive economically, you can easily cut your
fuel consumpt ion by 10-15 percent . This sec­
tion w ill give you some tips on how you can
help the env ironment and your pocketbook.
(D Tips
The consumption estimates as published
by ENVIRONMENTAL PROTEC TION AGENCY
( E PA) and Transpo rt Canada may not cor re­
spond to your actual consump tion on the
road, which will vary depending upon vehi­
cle load and speed, road and weather con ­
dit ions, trip length, etc.
Drive smoothly and keep a lookout
ahead
Vehicles use the most fuel when they are ac­
celerating.
.,. Avoid unnecessary accelerating and braking.
Vehicles use the most f uel when they a re ac­
ce lerat ing. If you ant icipate what is going to
happe n next, you will need to brake less and,
th us, acce lerate less . Let the vehicle coast
whenever possible -for examp le when you see
that the next traff ic light is red.
•
•

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
Vehicl e ca re a nd cl eanin g 18 5
Rinse the vehicle thoroughly with water. Then
clean using a neutral shampoo and a soft mi­
crofiber cloth.
Rinse the vehicle tho roughly again and let it
air dry. Remove any water residue using a
shammy .
A WARNING
-Only wash the vehicle when the ignition
is off and follow the instructions from
the car wash operator to reduce the risk of accidents .
- To reduce the risk of cuts, protect your­
self from sharp metal components when
wash ing the underbody or the inside of
the wheel housings .
- After washing the vehicle, the braking ef­
fect may be delayed due to mo isture on
the brake rotors or ice in the winter. The
brakes must be dried first with a few
careful brake applicat ions.
- If you wash the vehicle in an automatic car wash, you must fold the exterior m ir­
rors in to reduce the r is k of damage to
the mirrors. Power folding exterior m ir­
rors* must only be folded in and out us­
i ng the power folding function. -
To prevent paint damage, do not wash
the vehicle in direct sunlight.
- T o reduce the r isk o f damage, do not
wash the power top with a pressure
washer.
- To reduce the risk of damage to the sur ­
face, do not use insect removing spong­
es, kitchen sponges or similar items.
- Matte finish painted vehicle compo­ nents:
- To reduce the risk of damage to the surface, do not use polishing agents or hard wax.
- Never use car wash cycles that apply
protective wax. It can destroy the
matte fin ish effect.
- Do not place any stickers or magnet ic
signs on vehicle parts painted w ith
matte fin ish paint. The paint cou ld be
damaged when the stickers o r magnets
are removed.
@ For the sake of the environment
Only wash the vehi cle in facilities spec ial ly
designed for that purpose. This will red uce
the risk of dirty water contaminated with
oil from entering the sewer system.
Cleaning and care information
When clean ing and caring for individua l vehi ­
cle components, refer to the fo llowing tab les.
The information contained there is simply rec­ ommendations . For questions or for compo- nents that are not listed, re
fer to an author­
ized Audi dea ler or qualified workshop . A lso
follow the information found in
Q & .
Cle anin g ext erio r
Component Situation Solution
Wipe r bl ade s
Dirty <=> page 5 7, Cleaning windshield wiper blades
Hea dli ght s/ Dir ty Soft sponge with a m
ild soap solutional
tail li ghts
S en so rs /
Dirty Sensors: soft cloth with a so lvent-free cleaning product
c a mera l ense s Camera lenses: soft cloth with an alcohol -free cleaning
solution
Snow/ice Hand brush/so
lvent-free de-icing spray
•
•

"' N
a: LL co
rl I.O
"' rl
"' rl
Checking and filling Engine hood
Releasing and opening the engine hood
The engine hood is released from inside the
vehicle .
Fig . 172 Dr iver's side footwell: eng ine hood release
lever
F ig . 173 Re lease lever un der the engine hood
Before opening the engine hood, make sure
that the windshield w ipers are flat against the
windshield. Otherwise, they could damage the
paint on the hood.
.. With the driver's door open, pu ll the lever
under the instrument panel in the direction
of the arrow
q fig. 172.
.. Raise the hood slightly q &.
.. Press the rocker switch under the hood up­
ward
c::> fig . 173 . This re leases the catch .
.,. Open the hood.
& WARNING
Hot engine coo lant can burn you.
- To redu ce the r isk of being burned, never
open the hood if yo u see or hear steam
or coolant escaping from the engine
compartment. Wait until no steam or
Checkin g and fillin g 195
coolant can be seen or heard before care­
fully opening the hood.
Closing the engine hood
.. Pull the hood down until the pressure from
the struts is reduced .
.. Let the hood
drop down and latch in place .
Do not try to push it shut; it may fail to en­
gage
q &, .
_&. WARNING
-
A hood that is not comple tely latched
could fly up and b lock your view while dr iv­
ing.
- When you close the engine hood, chec k it
to make sure the safety catch has p ro pe r­
ly engaged . The hood sho uld be flush
with the surrounding vehicle body parts .
-If you notice while driv ing that the hood
is not secured prope rly, stop at once and
close it.
Working in the engine compartment
Be especially careful whenever you work in the engine compartment .
Whenever yo u mu st p erform an y w or k in th e
eng in e compa rtment, for example checking
and filling differ ent fluid s, there i s a ri sk of
injury , burns and accidents. To prevent per­
sonal injury always obser ve the following
WARNINGS . The eng ine compa rtment of an y
v ehicle is a hazardous are a
q A.
_&. WARNING
To help avoid injury, before you check any­
thing under the hood:
- Turn off the engine.
- Remove the ignition key.
- Apply the parking brake .
- Move selector lever of automatic trans -
mission to "P" (Park).
- Always le t the engine cool down . Hot
components wi ll bur n skin on contact .

"' N
a: LL co
rl I.O
"' rl
"' rl
Checking and fillin g 197
Engine compartment
Engine compartment
These are the most important items that you can check.
Fig. 174 Typical layout for containers and engine oil filler cap
(D Coolant expansion tank (- L) . . . 202
@ Jump start point(+) under a cov-
er .. .. ... ....... ........ ..
207, 256
@ Engine o il filler cap ( @ Jump start point(-) with hex
head screw ............ .... .
207, 256
© Brake flu id reservoi r((())) . . . . . 204
® W indshie ld/headlight* washer
container
(0) . . . . . . . . . . . . . . 208
A WARNING
Before yo u check anything in the engine
compartment, always read and heed all
WARNINGS
q .& in Working in the engine
compartment on page 195.
-
Engine oil
Engine oil specifications
The engine oil used must conform to exact
specifications .
The service interval disp lay in the instrument
cluster of your vehicle will inform y ou when it
is time for an oil change. We recommend that
you have your oil changed by an authorized
Audi Se rv ice Advisor .
If you have to top off the o il between o il
changes, use the Audi o il quality standard
specified in the tab le.
Audi oil quality standard
Gasoline
VW 502 00 or
eng ine vw 504 00 ...

204 Checking and filling
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance .
N N ~ N
" (X) (0
Fig. 179 Engine compartme nt: Cover on the brake flu ·
id reservo ir
Before you check anything in the engine com­
partment,
a lwa ys re ad and heed all WARN·
ING S ¢.&._ in Working in the engine compart­
ment on page 195 .
.. Read the brake fluid level from the brake
fluid reservoir
¢ fig . 179 , ¢page 197,
fig . 174.
The brake fluid level must be be ­
tween the "MIN" and
"MAX" markings.
The brake fluid reservoir is located at the rear
partition of the engine compartment on the
left side
¢ page 197.
The fluid level may drop slightly after some
time due to the automatic adjustment of the
brake pads. This is not cause for alarm.
If the brake fluid level falls
considerably be­
low the "MIN" mark, the brake warning/indi­
cator light (U.S. models:
11111 , Canadian
models :. ) will come on
¢page 15. Do not
continue to operate the vehicle. The complete brake system should be thoroughly checked
by an authorized Audi dealer or qualified
workshop and the cause corrected .
If the
brake fluid level is too low, the brake warn ing/
indicator light w ill illuminate. Contact an au­
thorized Audi dealer
immedi atel y.
@ Tips
The brake fluid reservoir is located under­
neath the cover.
Changing brake fluid
Have the brake fluid changed by an experi­
enced technician .
Brake fluid absorbs moisture from the air. If
the water content in the brake fluid is too
high, corrosion in the brake system may result
after a period of time . The boiling point of the
brake flu id will also decrease conside rably and
decrease braking pe rformance.
Therefore, the brake fluid must be changed
every two year s. Always use new brake flu id
which conforms to Federal Motor Veh icle
Standard "F MVSS 116 DOT 4".
The brake fluid reservoir can be diff icult to
reach, therefore, we recommend that you
have the brake fluid changed by your author­
ized
Audi d ealer . Your dealer has the correct
tools, the right brake fl uid and the know -how
to do this for you .
A WARNING
- Brake fluid is poisonous . It must be stor­
ed only in the closed original container
out of the reach of children!
- Brake failure can resu lt from o ld or inap­
propriate brake flu id. Observe these pre­
cautions:
- Use only brake f luid that meets SA E
specifica tion
J 1 7 03 and conforms to
Federa l Moto r Ve hicle Standard 1 16.
Always check with yo ur authorized Aud i
dealer to make sure yo u are using the
correct brake fluid. The correct type of brake f lu id is also indicated on the
brake fluid reservoir.
- The brake fluid must be new. Heavy use
of the brakes can cause a vapor lock if
the brake fluid is left in the system too
l ong. This can seriously affect the effi­
c iency of the brakes as well as your
safety. This cou ld resu lt in an accident.
(D Note
Brake fluid will damage the paint of your
vehicle .