ESP AUDI RS5 CABRIOLET 2015 Repair Manual

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
Vehicl e ca re a nd cl eanin g 18 7
Component Situ ation Solution
P las tic parts
Dirty Damp cloth
Heavily soiled Mild soap solutional, solvent-free plastic cleaning solu-
t ion, if necessary
Di spl ays Dirty Soft cloth with LCD cleaner
Co nt rols Dirty Soft brus
.h, then a soft cloth with a mild soap solutio nal
S afe ty be lt s Dirty Mild soap solutional, allow to dry before letting them re-
tract
Tex tile s, Stains adhering to
Vacuum cleaner
Vin yl, the surface
Alcantara Water-based stains Absorbent cloth and m ild soap solutional
such as coffee, tea,
blood, etc.
Oil-based stains Apply a mild soap solutional, blot away the dissolved oil
such as oil, make- or dye, treat afterward w ith water, if necessary
up, etc.
Special stains such Special
stain remover, blot with absorbent material,
as ballpoint pen, treat afterward with mild soap solutional, if necessary
nail polish, latex
paint, shoe polish,
etc.
N atur al lea ther Fresh stains Cotton cloth with a mild soap solutiona>
Water-based stains Fresh stains: absorbent cloth
such as coffee, tea, Dried stains: stain remover suitable for leather
blood, etc.
Oi l-based stains Fresh stains: absorbent cloth and stain remover suitable
such as oil, make- for leather
up, etc. dried stains: Oil cleaning spray
Special stains such Sta in remover sui table for leather
as ballpoint pen, nai l polish, latex
pa int, shoe polish,
etc.
Ca re Regularly apply condit ion ing c ream that protects from
light and penetrates into the mater ial. Use specially-col-
ored condit ioning cream, if necessary.
Carb on p art s Dirty Clean the same way as plastic parts
al Mild soap solution: maximum two tablespoons neu tral soap in 1 quart ( 1 lite r) of water
& WARNING
T he windshie ld may not be treated with
wate r-repelling windshie ld coating agents .
Unfavorab le conditions such as wetness,
darkness, or low sun can result in in-
-
creased glare. Wiper b lade chatter is also
possib le.
(D Note
- Hea dlight s/tail ligh ts
•
•

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
Many gasoline grades are blended to perform
especia lly we ll for winter or summer driving.
During seasonal change-over , we suggest that
you fill up at busy gas stations where the sea­ sonal adjustment is more likely to be made in
time.
Q;) Note
- Methanol fuels which do not meet these
requirements may cause corrosion and
damage to plastic and rubber compo ­
nents in the fuel system.
- Do not use fuels that fail to meet the
spec ified criter ia in this chapter .
- If you are unable to determine whether
or not a particular fuel blend meets the
spec ificat ions, ask your service station or
i ts fuel supplier .
- Do not use fuel for which the contents
cannot be identified.
- Fuel system damage and performance
problems resulting from the use of fuels
different from those specified are not
the respons ibility of Audi and are not
covered under the New Vehicle or the
Emission Control System Warranties.
- If you experience a loss of fue l economy
or driveability and performance prob­ l ems due to the use of one of these fuel
blends, we recommend that you switch
to unblended fuel.
Gasoline additives
A major concern among many auto manufac­
turers is carbon deposit build-up caused by
the type of gasoline you use .
Although gasoline grades differ from one manufacturer to another, they have cer tain
things in common. All gasoline grades contain substances that can cause deposits to collect
on vital engine parts, such as fuel injectors
and intake valves. Although most gasoline
brands include additives to keep engine and
fuel systems clean, they are not equally effec­
tive.
Fuel supply and filling your fuel tank 191
Audi recommends using TOP TIER Detergent
Gasoline . For more information on TOP TIER
Detergent Gasoline, please go to the official
website (www .toptiergas .com) .
After an extended period of using inadequate
fuels, built -up carbon deposits can rob your
engine of peak performance.
CJ) Note
Damage or malfunction due to poor fuel
quality is not covered by the Audi New Ve­
hicle Limited Warranty.
Fuel tank
Fuel filler neck
The fuel filler neck is located on the right rear
s ide panel behind the fuel filler flap.
If the power locking system should fail, you
can still open the flap manually -for detailed
instructions see
~ page 193.
You can find the fuel tank capacity of your ve ­
hicle in
~page 262 .
The label on the inside of the fuel filler flap
tells you the correct fuel for your vehicle. For
more information about fuel specifications,
see
~ page 190 .
Your vehicle fuel tank has an on-board refuel­
ling vapor recovery system. This feature helps
to prevent fuel vapors from escaping from the
tank and pollut ing the environment while you
refuel your vehicle. In order to fill the tank
properly while protecting the environment,
please follow this refueling procedure careful­
ly.
A WARNING ~
Under normal operating conditions, never
carry additional fuel containers in your car.
Gas canisters and other containers used to
transport fuel can be dangerous. Such con­
tainers, full or empty, may leak and could
cause a fire in a collision . If you must
transport fuel to use for your lawn mower, ..,.
•
•

"' N
a: LL co
rl I.O
"' rl
"' rl
fuel container in your vehicle. The con­
tainer, full or empty may leak and co uld
cause a fire, especially in a crash.
- If, under exceptional circumstances, yo u
must transport a portable fuel container,
please observe the following:
- Never fi ll a po rtable fue l container
while it is anywhe re in or on the vehicle
(for examp le, in the luggage compar t­
ment, or on the tr unk). Static electric i­
ty can bui ld up while fi lling and can ig­
n ite fue l vapors causing a fire .
- Always p lace a portable fuel container
on the gro und before filling.
- Always keep the fi ller nozzle comp lete­
ly inside the po rtable conta iner before
and during filling.
- If filling a portable container made of
metal, the filler nozz le must always be
in contact with the container. Th is w ill
he lp prevent static electricity from dis­
charging and cause a fire .
- Never sp ill fuel inside the vehicle or
luggage compartment. Fue l vapors are
h ighly f lammable .
- Always observe local and state/provin­
cial laws regarding the use, storage
and tra nsporta tion of fuel co ntainers .
- Make certai n the fuel container meets
industry standards (ANSI/ ASTM
F852 -86) .
(D Note
If any f uel has spilled onto the car, it
should be removed immediate ly to prevent
damage to the paint.
~ For the sake of the environment
As soon as the correctly operated nozzle sw itches off automatically fo r the fi rst
time, the tank is full. Do not try to add more fue l because fue l may spill out . In
add it io n, th e expans ion space in the fuel
t ank will be fi lled -cau sing the fue l to
overflow whe n it be come s w arm and pol ­
lu te the env iro nment.
Fu el suppl y and filli ng your fuel t ank 193
@ Tips
- Running your eng ine whi le refue lli ng
may cause vapors to escape or even
cause fuel to sp ill out of the tank. T his
would then shut off the fuel nozzle be­
f o re the ta nk is f ull.
- Do not refuel your vehicle with the ign i­
tion turned o n. The fuel gauge may oth­
erwise not indicate the correct f uel level
after refuelling .
- The fue l filler flap of yo ur vehicle is not
locked when you lock t he veh icle from
t he insid e.
Unlocking the fuel filler flap
by hand
You can open the fuel filler flap by hand if the
power locking system should fail .
Fig. 1 70 Luggage compa rtme nt: ope ning th e side trim
Fig . 1 71 Luggage co mpa rtme nt: Eme rgency ope ning
of fue l fil le r flap
The emergency opening mechanism is located
behind the right side trim panel in the lug­
gage compartment .
Opening the side trim .,. Insert a tool such as a screwdriver
¢
page 242 or the emergency key into the
r ight side of the upper gap¢
fig. 170 . .,.

"' N
a: LL co
rl I.O
"' rl
"' rl
Checking and filling Engine hood
Releasing and opening the engine hood
The engine hood is released from inside the
vehicle .
Fig . 172 Dr iver's side footwell: eng ine hood release
lever
F ig . 173 Re lease lever un der the engine hood
Before opening the engine hood, make sure
that the windshield w ipers are flat against the
windshield. Otherwise, they could damage the
paint on the hood.
.. With the driver's door open, pu ll the lever
under the instrument panel in the direction
of the arrow
q fig. 172.
.. Raise the hood slightly q &.
.. Press the rocker switch under the hood up­
ward
c::> fig . 173 . This re leases the catch .
.,. Open the hood.
& WARNING
Hot engine coo lant can burn you.
- To redu ce the r isk of being burned, never
open the hood if yo u see or hear steam
or coolant escaping from the engine
compartment. Wait until no steam or
Checkin g and fillin g 195
coolant can be seen or heard before care­
fully opening the hood.
Closing the engine hood
.. Pull the hood down until the pressure from
the struts is reduced .
.. Let the hood
drop down and latch in place .
Do not try to push it shut; it may fail to en­
gage
q &, .
_&. WARNING
-
A hood that is not comple tely latched
could fly up and b lock your view while dr iv­
ing.
- When you close the engine hood, chec k it
to make sure the safety catch has p ro pe r­
ly engaged . The hood sho uld be flush
with the surrounding vehicle body parts .
-If you notice while driv ing that the hood
is not secured prope rly, stop at once and
close it.
Working in the engine compartment
Be especially careful whenever you work in the engine compartment .
Whenever yo u mu st p erform an y w or k in th e
eng in e compa rtment, for example checking
and filling differ ent fluid s, there i s a ri sk of
injury , burns and accidents. To prevent per­
sonal injury always obser ve the following
WARNINGS . The eng ine compa rtment of an y
v ehicle is a hazardous are a
q A.
_&. WARNING
To help avoid injury, before you check any­
thing under the hood:
- Turn off the engine.
- Remove the ignition key.
- Apply the parking brake .
- Move selector lever of automatic trans -
mission to "P" (Park).
- Always le t the engine cool down . Hot
components wi ll bur n skin on contact .

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro ­
tects the engine from freezing in the winter .
The cooling system is sealed and generally re­
quires little attention.
T he cooling system has been filled at the fac­
tory with a permanent coolant which does not need to be changed. The coolan t consists of a
mixture of specially conditioned water and the
manufacturer 's glycol-based coolant addi-
tive G13 antifreeze with ant icorros ion addi­
tives (50% for USA models ; 60% for Ca nadian
models) . Th is mixture both assures the neces­
sary frost protection and protects metal com­
ponents in the engine's coo ling system from
corrosion and scaling. It a lso raises the boil­
ing point of the coo lant.
D o not reduce the concentration o f the coo l­
ant in the summer by adding plain water .
The
proportion of coolant additive mu st be at
least 50 % but not more than 60 %
to main­
tain antifree ze protection and cooling efficien­
cy. If the coolant frost protect ion is too low,
the coolant could freeze and damage the veh i­
cle heating and eng ine cooling system .
For year-round driving, antifree ze is added at
the factory for temperatures down to:
- -31° F(-35°C)USA
- - 4 0 ° F ( -40 °C) Canada.
I f you must add coo lant, use a m ixture of wa­
ter and coolant addit ive. Mixing the coolant
addi tive wi th disti lled wate r is recommended.
A WARNING
Be fore yo u check any thing in the engine
compartment, always read and heed all
WARNI NGS
~ .&. in Working in the engine
compartment on page 195.
(D Note
- Befo re win ter sets in, have the coolan t
checked to see if t he coolant ad dit ive in
-
Checkin g and fillin g 201
your vehicle is sufficient to meet the cli ­
mate conditions . This is especia lly impor ­
tant if you live in a region where the win ­
ter is extreme ly co ld. If necessary, in­
c rease the p ropo rtion of coo lant add itive
to 60% .
- When adding coolant additive to your
cooling system, remember:
- We re commend using on ly coola nt ad­
d itive G 12++ or G 13 for your veh icle .
T his coolan t ad di tive is availab le a t au­
thor ized Audi dealers. Other types of
antifreeze can significantly reduce cor ­
rosion protection. The resulting corro­
sion can cause a loss of coolant and se­
rious engine damage .
- Do not add any type of rad iator leak seal­
ant to your vehicle's engi ne coolant .
Add ing radiator repa ir flu id may adverse ­
ly affect the f unction and performance of
your cooling system and cou ld resu lt in
damage not covered by you r New Ve hicle
Li mited War ran ty.
•
•

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
@ For the sake of the environment
Because of the pr oblem of proper d isposa l
of brake flu id as we ll as the special tools
requ ired and the necessary expert ise, we
recommend that you have the brake fluid
changed by your author ized Audi dealer .
Battery
General information
Under normal operating conditions, the bat­
tery in your Audi does not need any mainte ­
nance. With
high outside temperatures or
long daily dr ives we recommend that you have
the electro lyte level checked by an authorized
Aud i dealer or qualified workshop . The elec­
trolyte leve l should also be checked each time
the battery is charged c>
page 207.
Have the battery checked when you take your
ve hicle in for service . You are well adv ised to
replace a battery that is older than 5 yea rs .
W ith certa in types of a irbag deployment, t he
battery is d isconnected from the vehicle elec­
tr ica l system for safety reasons c>
.&. in Re­
pair, care and disposal of the airbags on
page 144.
Disconnecting the battery terminals
Some vehicle functions (power w indow regu­
lators, for example) are lost if the battery ter­
m inals a re d isconnected. These func tions have
to be re lea rned after the batte ry term inals a re
connected agai n. T o prevent this, the bat tery
should only be d isconnec ted from the vehicle
e lec tric al system when absolu tely necessa ry
for repairs .
Vehicles not driven for long periods
If you do not drive you r vehicle over a period
of severa l days or weeks, elec trical compo­
nen ts are gr adually cut b ack o r swi tched off .
This redu ces energy cons umption and main­
tains starting capab ility over a longer per io d
c> page 177.
Some o f the conven ience f unctions m ay not
ope rate, su ch as the in ter ior lig hts or t he
Checkin g and fillin g 205
power seat adjus tment. The convenience
funct io ns w ill be available again when yo u
turn o n the ign ition and start the engine.
Winter operation
D ur ing the w inte r mon ths, bat tery capa city
tends to dec rease as tempera tures drop . This
is beca use more power is a lso consumed wh ile
starting, and the headlights, rear window de­
fogger, etc., are used more often.
Avoid unnecessary powe r consumpt ion, pa r­
ticular ly in city traffic or when traveling only
sho rt distances. Let yo ur authorized A udi
dealer check the capacity of the vehicle bat ­
tery before w inter sets inc>
page 207. A well
charged battery will not on ly prevent starti ng
problems w hen the weather is cold, but w ill
also last longer.
@ Tips
If your vehicle is left standing for seve ral
weeks at extremely low temperatures, the
vehicle battery s hou ld be removed and
stored where it will not freeze . This will
p revent it from be ing damaged and having
to be repla ced.
Working on the battery
Be especially careful when working on or near
the bat tery.
The battery is located in the luggage compar t­
ment under the floor . B efo re you che ck any­
thi ng in the luggage compartment,
read and
heed all WARNINGS
c> ,&. .
Always heed the safety warnings , when work­
i ng on the veh icle batte ry or t he vehicle e lec­
t rical sys tem to p reven t inju ry.
The following WARNINGS are very
important when working on the battery:
Always heed the following WARNING SYM· BO LS and safety precautions when working
on the battery .
®
Always wear eye protection.
•
•

208 Check ing and filling
- To r educe the danger of explosion, never
co nnect or disconn ect cha rger cables
wh ile the c harger is operating.
- Fast char ging a battery is dangerous and
shou ld on ly be attempted by a compe­
tent technician w ith the proper equip­
ment .
- Battery acid that may spill during charg­
ing should be washed
off with a solution
of warm water and baking soda to neu ­
tralize the acid.
(Q) Note
Never use a fast charger as a booster to
start the engine . This will seriously dam­
age sensitive electronic components, such
as control units, relays, rad io, etc., as we ll
as the battery charger.
Battery replacement
The new battery must have the same specif/·
cations and dimensions as the original equip­
ment battery.
Intell igent energy management in your veh i­
cle is respons ible for d istributing the e lectr i­
cal energy throughout you r vehicle
q page 177. The intell igen t energy m anage­
men t system w ill keep the engine ba tte ry
charged better then vehicles w ithout this sys­
tem . To make sure the additional e lectrica l en­
ergy is available once again after you have
changed the battery, we recommend that you install batteries o f the same type and ma nu­
facture only (the same as those installed at
the time your vehicle was delivered). Specifi­
cations are listed on the battery hous ing. Your
author ized Audi dealer must code the battery
in the ene rgy management system to enable
you to use the energy management functions
correctly after replac ing the battery.
I f it is not poss ible to use a battery of this
type, the new bat tery m ust h ave the s ame ca­
pac ity, voltage ( 12-volts), amperage, con ­
struction and plug sea ling. When installing the battery, make su
re the ig ­
nition and a ll electrical consumers are turned
off.
(D Note
Make sure the ventilation hose on the side
of the battery is connected, otherwise
fumes or battery acid can leak out .
@ For the sake of the environment
Because o f the p rob lem of p roper disposal
of a battery, we recommend your author ­
i zed Audi dealer change the battery for
you. Batteries contain sulfur ic acid and
l ead and must always be disposed of prop­
erly in comp liance with all environmental
regulations. Dispos ing of vehicle batter ies
i mprope rly is very dange rous to the envi­
r o nment .
Windshield/headlight*
washer container
Fig. 181 En gin e compa rt m en t: Cove r on the w ind·
s h iel d a nd h eadligh t• was her fluid conta in er
.., N
-~ (X) a,
The washer fluid conta iner is marked w ith the
symbol
O on its cap q fig . 181, qpage 197,
fig . 174 .
.. Before yo u check any thing in the engine
compa rtment,
always read and heed all
WARNINGS q A in Working in the engine
compartm ent on page 195 .
.. Lift the fi ller cap tongue to add washer flu­
id. You can f ill the container to the top.
.. Press the cap back onto the filler neck after
fi lling the conta iner .
You can find the reservo ir
capacity in the table
in
q page 262. .,.

Tires and wheels 211
and make of tire and the tread -New tires tend to be slip-•
pattern.
pery and must also be bro-• '
Hidden damage ken-in. To reduce the risk of
Damage to tires and rims is of -losing control, a collision
and serious personal inju-
ten not readily visible. If you ries, drive with special care
notice unusual vibration or the for the first 350 miles
vehicle pulls to one side, this (560 km).
may indicate that one of the -Driving with worn or dam-
tires has been damaged . The
aged tires can lead to loss of
tires must be checked immedi-
ately by an authorized Audi control
, sudden tire failure,
including a blowout and
dealer or qualified workshop.
sudden deflation, crashes
Unidirectional tires and serious personal inju-
A unidirectional tire can be ries. Have worn or damaged
identified by arrows on the tires replaced immediately.
sidewall, that point in the di rec- -Tires age even if they are
tion the tire is designed to ro- not being used and can fail
tate. You must follow the speci- suddenly, especially at high
fied direction of rotation. This is speeds. Tires that are more
necessary so that these tires than 6 years old can only be
can develop their optimum used in an emergency and
characteristics regarding grip, then with special care and
road noise, wear and hydro- at low speed.
planing resistance. For more in- -Never mount used tires on
formation
¢ page 249. your vehicle if you are not sure of their "previous histo-
A WARNING
ry." Old used tires may have -
New tires or tires that are been damaged even though
old, worn or damaged cannot the damage cannot be seen
provide maximum control that can lead to sudden tire
M
and braking ability. N
er failure and loss of vehicle u.. co ,...., \!) control. 1.1'1 ,...., 1.1'1 ,....,

212 Tires and wheels
-If you notice unusual vibra­
tion or if the vehicle pulls to
one side when driving, al­
ways stop as soon as it is
safe to do so and check the
wheels and tires for dam­
age.
0 Note
-Please note that summer and winter tires are de­
signed for the conditions
that are typical in those sea­
sons. Audi recommends us­
ing winter tires during the
winter months. Low tem­ peratures significantly de­
crease the elasticity of
summer tires, which affects
traction and braking ability. If summer tires are used
in
very cold temperatures, cracks can form on the tread
bars, resulting in perma­
nent tire damage that can
cause loud driving noise and
unbalanced tires. Audi is not
responsible for this type of
damage.
-Burnished, polished or chromed rims must not be used in winter road condi­
tions. The surface of the
rims does not have suffi­
cient corrosion protection
for this and could be perma­
nently damaged by road salt
or similar substances.
Glossary of tire and loading terminology
Accessory weight
means the combined weight (in
excess of those standard items
which may be replaced) of auto­ matic transmission, power
steering, power brakes, power
windows, power seats , radio,
and heater, to the extent that
these items are available as fac­
tory-installed equipment (whether installed or not).
Aspect ratio
means the ratio of the height to
the width of the tire in percent.
Numbers of 55 or lower indi­
cate a low sidewall for im­
proved steering response and
better overall handling on dry
pavement.
...

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Bead
means the part of the tire that
is made of steel wires, wrapped
or reinforced by ply cords and
that is shaped to fit the rim.
Bead separation
means a breakdown of the bond
between components in the
bead.
Cord
means the strands forming the
plies in the tire .
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manu­
facturer for a tire of a designat­
ed size that has not been driven
for more than a couple of miles (kilometers) at low speeds in
the three hour period before
the tire pressure is measured or
adjusted.
Curb weight
means the weight of a motor
vehicle with standard equip­
ment including the maximum
capacity of fuel, oil, and cool­
ant, air conditioning and addi­
tional weight of optional equip­
ment.
Tires and wheels 213
Extra load tire
means a tire design to operate
at higher loads and at higher inflation pressures than the
corresponding standard tire. Extra load tires may be identi­
fied as "XL", "xl", "EXTRA
LOAD", or "RF" on the sidewall.
Gross Axle Weight Rating ("GAWR")
means the load-carrying capaci­
ty of a single axle system,
measured at the tire-ground in­
terfaces.
Gross Vehicle Weight Rating ("GVWR")
means the maximum total
loaded weight of the vehicle.
Groove
means the space between two
adjacent tread ribs.
Load rating (code)
means the maximum load that
a tire is rated to carry for a giv­
en inflation pressure. You may
not find this information on all
tires because it is not required by law.
•
•
'