ignition AUDI RS7 SPORTBACK 2015 Owners Manual

10 Instruments and warning/indicator lights
Instruments and warning/indicator Lights
Instruments
Instrument cluster and controls
The instrument cluster is your central source of information.
Fig. 3 Overv iew of the inst rument cluster
CD Coolant temperature gauge ...
@ Tachometer (engine rev counter)
@ Turn signals ........... .. .. .
© Display with
- Driver information system .. .
- Warning/ind icator lights
® Tachometer 10
11
46
22
11
@ Fuel
gauge . . . . . . . . . . . . . . . . . 11
@ Tips
The instrument illumination (for dials and
needles) turns on when the ignition is on
and the vehicle lights are turned off . As
the daylight fades, the illumination of the
dia ls likewise dims automatically and will
go out completely when the outside light
is very low. This feature is meant to rem ind
you to switch on the headlights when out­
side light conditions become poor.
Engine coolant temperature gauge
The engine coolant gauge CD c:> page 10, fig. 3
only works when the ignition is on . To prevent
damage to your engine, please note the fol­
l owing important points:
Engine cold
,.._ N
9 (!)
" a,
If only the LEDs at the bottom of the gauge
turn on, the engine has not reached operating
temperature yet. Avoid high engine speeds, heavy engine loads and heavy th rottle applica­
t ions.
Normal temperature
The engine has reached its operating temper­
ature once the LEDs up to the center of the
gauge turn on unde r normal driv ing cond i­
t ions . Th e LEDs higher up may turn on when
the engine is under heavy load or the exterior
temperature is high. This is no need to worry
as long as the . warning light in the instru­
ment cluster does not illum inate . If the LEDs
in the upper area of the disp lay and the indica­
tor light . in the instrument cluster display
turn on, the coolant temperature is too high
c:> page 15.
A WARNING
-Always observe the warn ing in
c:> page 211, before opening the hood
and checking the engine coolant level.

M N
0:: <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Instrument s and warnin g/indic ator ligh ts 11
- Never open the engine hood if you see or
hear steam, or if you see engine coolant
dr ipping from the engine compartment.
You could burn yourself . Let the engine
cool off first until you can no longer see
or hear steam or coo lant escaping.
Q) Note
- Mount ing additional lights or accessories
i n front of the a ir inlets reduces the cool­
i ng effect of the rad iator . At h igh outside
temperatures or high eng ine load, the
engine could overheat.
- The front spo ile r has been designed to
proper ly distribute the cooling air wh en
t h e veh icle i s moving.
If the spoiler is
damaged, this cou ld red uce the cooling
effect and the engine co uld then over ­
heat . Ask yo ur authorized Audi dea ler fo r
ass istance.
Tachometer (engine rev counter)
The tachometer indicates the engine RPM
(revolutions per minutes).
If engine R PM drops be low 1 ,500, you should
downshift to the next lower gea r. T he red area
at the end of the sca le indicates maximum
pe rmissib le engine RPM after the break- in pe­
riod. Before reach ing this area, move these­
lector lever to position 0/5 (Drive) or ease
your foot off the accelerator peda l.
(D Note
The tachometer needle should only br iefly
be in the red zone: you cou ld damage your
eng ine! The beginn ing of the red zone var­
ies depending on the operati ng tempera­
ture of the eng ine .
@ For the sake of the environment
Upshift ing early saves fuel and reduces en­
gine noise.
@ Tips
The engine speed is limited when the en­
g ine is co ld - the full engine output is not ava
ilable . When the engine is at operating
temperature, the red area in the tachome­
ter moves to a higher RPM range.
Fuel gauge
The fuel gauge only works when the ignition is
on. If the fue l level drops below 2 .6 gallons
(10 lite rs), the bottom LED turns red and the
indicato r light
(j) turns on ¢ page 20. The
bottom L ED blinks red whe n the fuel level is
very low.
The possible range based on the current fuel level is shown in tab@¢
page 22, fig. 4.
(D Note
Neve r run the ta nk completely dry. A n ir­
r egular supply of f uel can cause engine
misfiring and fuel could enter the exha ust
system. The catalytic co nve rter could t hen
ove rheat and be damaged .
Warning/indicator
Lights
Description
The ind icator lights in the instrument cluster
blink or tur n on. They indica te f unct ions or
malfunctions ¢
&.
Messages may appea r with some indicato r
li ghts. A warning signal will sound at t he
same t ime . The indica to r li ghts and messages
i n the center of the displays may be rep lace d
by other disp lays. To show them again, select
the tab for ind icator lights and messages us­
ing the multif unction steering whee l
¢
page 22. If there are several malfunc­
tions, you can display them one at a time us­ i ng the thumbwheel.
Some indicators lights in the d isp lay can turn
on in severa l co lors.
A WARNING
- Failure to heed warning lights and other
important vehicle informat ion may resu lt
IJI,,

12 Instrum ent s and w arn ing /indic ato r light s
in serious persona l injury or vehicle
damage.
- Whenever sta lled or stopped for repair,
move the vehicle a safe distance off the
road, stop the engine, and turn on the
emergency flasher
¢ page 45.
- The engine compartment of any motor vehicle is a potentially hazardous area.
Before you check anything in the engine
compartment, stop the engine and let it
cool down. Always exercise extreme cau­
t ion when wor king under the hood
¢page 211.
Overview
Some ind icator lights tu rn o n briefly to check
the function of that system when yo u switch
the ignition on. These systems are marked
with a ./ in the fo llowing tab les. If one of
these ind icator lights does not turn on, there
is a malfunction in that system .
Red ind icator light s
-------------
USA mo del s:
Brake malfunct ion ./
¢page 14
Safety belt
¢page 16
Electromechanical steering ./
¢page 192
Electronic steering column lock
¢page 17
Engine start system
¢page 17
Centra l indicator light
¢ page 18
USA model s: Speed warning
sys tem
¢ page 78
Canada models : Speed warning
system
¢ page 78
Adaptive cruise control *./
¢page83
Air suspension *
¢page 17
Pedestr ian warning*
~ page 99
Rear spoiler
¢page 190
Canad a mod els :
Brake malfunction ./
¢page 14
Yello w ind ic a to r lights
U SA mo dels:
El ectromechanical pa rking
brake
¢ page 15
Canada model s:
Electromechanical parking
brake
¢ page 15
Engine cooling system
¢page 15
Engine oil pressure
¢page 16
Engine oil leve l
¢page 17
Battery
¢page 16
-------------
USA m odels: Safety sy stems
¢ page 18
Canada mod els: Safety systems
¢ page 18
Electronic Stabilization Control
(ESC) ./
¢page 18
Electronic Stabilization Control
(ESC) ./
¢page 18
Electronic Stabilization Cont ro l
(ESC) ./
¢page 187
USA m odel s:
Ant i- lock bra king system (ABS)
de fect ive ./
¢page 18 ..,.

14 Instruments and warning/indicator lights
Adaptive cruise control*
9page 83
Audi act ive lane assist*
~ page 91
High beam
Qpage46
BRAKE/( ©) Brake system
The light illuminates when the ignition is
switched on. It goes out after the engine has
been started . Th is indicates that the brake
warn ing light is functioning properly.
If the brake warning light does not light up
when the engine is cranking , there may be a
malfunction in the electrical system. In this
case, contact your Audi dealer.
If the brake system warning/indicator light
turns on, there is a brake system malfunction .
• (USA models) ta (Canada models) Stop
vehicle and check brake fluid level
If the indicator light turns on and the mes­
sage appears, proceed as follows :
"" Pull off the road .
.. Stop the vehicle.
""Turn off the engine .
""C heck the brake fluid level ¢
page 220.
""Contact your neares t authorized repair fa-
cility if necessary.
Warning! Fault in brake system. Contact
dealer
If the ABS indicator light rJlm (USA models)/
[iJ (Canada models), the ESC indicator light
G1 and the b rake system indicator light
• (USA models)/. (Canada models) turn
on and the message appears, the ABS, ESC
and braking distribution are not working ¢
A.
Ca refully drive to your authorized Aud i dealer
immediately to have the malfunction correct­
ed ¢
,A.
• (USA models)/ . (Canada models) Park­
ing brake : system fault! Please contact deal­
er
- If the indicator light and the message ap ­
pear
when stationary or after switching the
ignition on ,
check if you can re lease the
parking brake. After releasing the parking
brake, carefully drive to your authorized
Aud i dea ler immediately to have the mal ­
fu nction corrected. If you cannot release the
park ing brake, seek professiona l assistance.
- If the ind icator light and the message ap­
pear
while driving , the emergency brak ing
function may not be available . It may not be
possible to set the park ing brake or release
it once it has been set. Seek profess iona l as­
sis tance.
(USA models) : If the warn ing light. and the
warning light
E+J appear together, immedi­
ately contact your au tho rized Aud i dealer or
qualified wo rkshop to have all brake pads in­
spected
¢ page 19 .
When the light comes on, an aud ible warning
s ignal is also g iven .
_& WARNING
-Always observe the warnings in
¢
page 211, before opening the hood
and checking the brake fluid .
- Driving with low brake fluid is a safety
hazard. Stop the car and get professiona l
assistance.
- If the. (USA models)/ . (Canada
models) brake system indicator light
turns on togethe r with the ABS and ESC
indicator lights, the ABS/ESC regulating
function may have failed. Functions that
stabilize the vehicle are no longer availa­
ble. This could cause the vehicle to
swerve and increase the r isk of slid ing .
Drive carefully to the nearest authorized
Aud i dealer or other qualified workshop
and have the ma lfunction corrected.
- If the brake wa rning/ind icator light does
not go out after a few seconds and the pa rking brake is re leased, or lights up
while you are dr iving, the f lu id l eve l in
the brake fluid reservoir is too low. If you
believe that it is safe to do so, proceed
Iii>

16 Instruments and warning/indicator lights
turn of the engine and allow it to cool. Follow the warning stickers
c::> page 211.
@ Note
Do not continue driving if the. symbol
illuminates. There is a malfunction in the
engine cooling system -you could damage
your eng ine.
0 Battery
This warning/indicator light detects a mal ­
function in the generator or in the vehicle's
electrical system.
The . warning/indicator light illuminates
when yo u switch on the ignition and must go
out after the engine has started.
• Alternator fault: Battery is not being
charged
If the indicator light turns on and the mes ­
sage appears, there is a ma lfunction in the
generator or vehicle e lectrica l system.
Drive to you r authorized Aud i deale r or quali­
fied workshop immediately. Because the vehi­
cle battery is discharging, turn off all unnec­
essa ry electrical equipment such as the radio .
Seek professional assistance if the battery
charge leve l is too low.
(•) Low battery: battery will be charged
while driving
If the indicator light turns on and the mes­
sage appears, there may be limited starting
ability.
I f th is message turns off afte r a litt le while,
the battery cha rged enough wh ile driving.
If the message does not turn off, have your
author ized Audi dealer or qualified workshop
correct the malfunction .
4'-Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The . warn ing/ indicator light illuminates
when the ignition is switched on to remind
the driver and any front passenger to put on
the safety belt. Addit ionally, an acoustic warn­
ing (gong) w ill also sound .
For more Information¢
page 130, ~ Safety
belt warning light.
"l!::7": Engine oil pressure malfunction
The red engine oil pressure warning symbol
requires immediate service or repair . Driving
with a low-oil-pressure indication is likely to
inflict severe damage to the engine .
• Switch off engine and check oil level
If the indicator light turns on and the mes­
sage appears, the oi l pressu re is too low.
.,. Pull off the road .
.,. Stop the vehicle.
.,. Turn off the engine .
.,. Check the engine oil level c::> page 21 S.
.,. If the engine o il level is too low, add eng ine
oil
¢ page 215. Make sure that the oil pres­
sure warning symbol. appears no longer
in the display before you start dr iv ing again .
.,. If the engine o il level is correct and the indi­
cator light still turns on, turn the engine off
and do not continue driving. Seek professio­
na l assistance .
@ Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev­
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter­
vals, preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
II requires oil refill or workshop serv­
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil ..,.

18 Instrum ent s and w arn ing /indic ato r light s
tl'l.l !f Safety systems
The II (USA models)/S,I (Canada mode ls) in­
d icator light monitors the safety systems (e .g.
a irbags, pretensioners) and illuminates for a
few seconds each time you switch the ignition
on.
I f the
II (USA mode ls)/ S,I (Canada models)
indicator light does not go out, or if it illumi­
nates while you are driving, or if it starts to
blink, then there is a ma lfunction somewhere
in the system.
If the light does not illuminate
when you switch the ignition on, this also means there is a malfunction.
A WARNING
If you have a malfunction in the safety sys­
tems, contact your author ized Audi dealer
immediate ly. Otherwise the safety sys­
tems may not wo rk properly in an acci­
dent.
& Central indicator light
I f the indicator light . or II turns on, check
the message in the instrument cluster.
;;,J {J Electronic Stabilization Control
(ESC)
If the J,.J indicator light blinks wh ile driving,
the ESC or ASR (Ant i- S lip Regulation) is active ­
ly regulating .
If the
Ji! indicator light turns on, the system
has sw itched the ESC off. In this case, you can
switch the ignition off and then on to switch
the ESC on again . The indicator light turns off
when the system is functioning fully .
If the
fil indicator light turns on, ESC was re­
stricted or switched off using the
I Y; OF F I but­
ton
Q page 187 .
Stabilization cont rol (E SC/ABS): F ault! See
o w ner 's manual
If the Ji! indicator light and the ABS indicator
light
fi1 (USA models) I ii] (Canada models)
turn on and the message appears, the ABS or
e lec tronic differen tial lock is ma lfunction ing. T
his also causes the ESC to malfunction. The
brakes still function with their normal power,
but ABS is not active.
Drive to your au thorized A udi dealer or quali­
fied workshop immed iate ly to have the mal­
function corrected .
A WARNING
-If the . (USA mode ls)/ . (Canada mod-
e ls) b rake system indicator light turns on
together with the ABS and ESC indicator
lights, the ABS/ESC regulating function
may have failed . Fu nctions that stabilize
the veh icle are no longe r available . T his
could cause the vehicle to swerve and in­
crease the risk of sliding. Drive carefully to
the nea rest au thori zed A udi dealer or oth­
er qualified workshop and have the ma l­
f u nction corrected.
@ Tips
Fo r additional in format ion on ESC and
ABS, refer to
Q page 187.
ABS/{ €,) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The wa rning/indicator light fi1 (USA mod-
els)
/ KG!ff (Ca nada models) w ill come o n for a
f ew seconds when the ignition is sw itched on.
T he light will go out after an automatic check
sequence is comp leted .
There is a malfunction in the ABS when:
-The warning/indicato r light does not illum i­
nate when you switch the ignit io n on.
- The warning/indicator l ight does not go out
after a few seconds.
- The warn ing/ indicator light illum inates
while d riving.
The ESC indicator lig ht also illum inates if
there is a malfunction in the ABS. The mes ­
sage
Stabi liz at ion control (ESC /ABS ): Fault!
See owner's manual
also appears in the in­
st rument cluste r d isplay and a wa rning tone
sounds.

20 Instruments and warning/indicator lights
If this warning/indicator light illuminates
while you are driving, then there is a mal­
function in the engine electronics. Have the malfunction corrected as soon as pos­
sible by your authorized Audi dealer or
qualified repair facility .
o Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (OBD II) system.
The symbol
¢..j lights up when the ignition is
switched on and will turn off after the engine
has started and has settled at a constant idle
speed. This indicates that the MIL is working
properly.
The warning light illuminates when there is a
malfunction in the engine electronic system.
Contact your authorized Audi dealer and have
the malfunction corrected .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate ¢ page 208.
For more information ¢ page 29.
!?) Engine speed limitation
II! Engine speed maximum XXXX RPM
The engine speed is automatically limited to
the speed displayed in the driver information
system. This protects the engine from over­
heating.
The engine speed limitation deactivates once
the engine is no longer in the critical tempera­
ture range and you have released the accelera­
tor pedal once.
If the engine speed limitation was activated
by an engine control malfunction, the indica­
tor light
Ga also turns on. Make sure that the
speed does not go above the speed displayed .
Drive to your authorized Audi dealer immedi­
ately to have the malfunction corrected.
'
(!) Tips
The engine speed is limited when the en­
gine is cold -the full engine output is not
available. When the engine is at operating
temperature, the red area in the tachome­
ter moves to a higher RPM range .
~~, Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your au­
thorized Audi dealer and have the oil sensor inspected . Until you have this done, check the
oil level each time you refuel just to be on the
safe side
¢ page 215.
? Request to warm engine by driving
0 Please warm up engine
Fuel has entered the engine oil because of low
outside temperatures or frequent short
drives . Drive until the engine is warm so that
the fuel in the engine oil will vaporize. Avoid
high engine speeds, full acceleration and
heavy engine load when doing this.
Bu Fuel level indicator
D Please refuel
If the indicator light turns on for the first
time and the message appears, there are
about 2.6 gallons (10 liters) of fuel left in the
tank. Time to refuel
¢ page 207.
D Tank system malfunction! Contact dealer
If the indicator light turns on and this mes­
sage appears, there is a malfunction in the
tank system.
Drive to your authorized Audi dealer immedi ­
ately to have the malfunction corrected.
' ~ Windshield washer fluid level
(r5 iJlease refill washer fluid ...

"' N
a:: I.J "". rl I.O
"' rl
"' rl
Instrument s and warning /indicator lights 23
® ®
Tab Content
2 Indicator lights and messages
Warning when a door, the hood or
the rear lid is not closed
Service interval display<=>
page 26
Speed warning system <=> page 78
3 Night vision assistant* <=> page 99
4 Audio/video
5 Telephone*
6 Navigation*
The second and third tabs are only visib le if at
l east one indicator light or message is shown
or if that system is switched on .
The status line © is located in the bottom
part of the display¢
fig. 4. It displays the ex­
terior temperature, time, selector lever posi­
tion, trip odometer and odometer .
F or some veh icle functions, you can access the
trip information from the temporary memory
<=> page 24 in the line(!)<=> fig. 5.
A WARNING 1= -
- Never rely exclusively on the outside
temperature display to determine if a
road surface is icy or not. Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice covered and
slippery even at an outside temperature above
41 °F (+5 °().
- Always reduce your speed and dr ive with
special care in cold weather conditions
when the chance of encountering icy
road surfaces increases.
@ Tips
-If the vehicle is stationary, or if you are
driving at a very low speed, the tempera­
ture shown in the display might be
s light ly higher than the actual outside
temperature. This is caused by the heat
being radiated from the eng ine.
- You can select the units used for temper­
ature, speed and other measurements in
the MMI. -
For information on the audio/video and
navigation* functions, refer to the sepa­
rate MMI owner's manua l.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering
wheel.
Fig. 6 Multifunction steering wheel: operating the driv­
er in formation system
Fig. 7 Driver informat ion system: opening the vehicle
func tions menu
Operating concept
.,. Switch the ignition on.
.,. To switch between the tabs, press the rocker
switch
(D to the left or rig ht <=> fig. 6.
.,. To access additional information below or
above, rotate the t humbwheel @down or
up.
.,. To confirm a selection, press the thumb ­
wheel @.
.,. Press the~ button @ to open a submenu
for an active tab.
.,. Press the button@) to access a function for
the prog rammab le steering whee l button* .
Accessing Vehicle functions
.,. Select the first tab with the rocker switch
(D.

24 Instruments and warning /indicator lights
• Press the button ~ @-The Vehicle func­
tion s
menu appears ¢ fig. 7 .
• To select a menu item, turn and press the
th umbwheel @.
Resetting value s to zero
• Se le ct t he on-board computer / Efficien cy
program
men u item in the Vehicle func­
tion s
menu.
• You can now select between the long -term
memory and short-term memory .
• To reset the values i n a memory, press and
hold the thumbwhee l@ for o ne second .
Assigning a function to the
programmable steering wheel button*
• Se lect : I CAR I funct ion button> (Car )* sys­
tems
control button > Vehicle settings >
Steering wheel button .
The last function selected displays when you
sw itch the ignition o n.
@ Tips
All stored values will be lost if the vehicle
battery is disconnected.
On -board computer
F ig. 8 I n st ru men t cl uster: fu el co nsumpt io n
You can call up the following information in
the on-board computer:
-D ate
- Dr iving tim e (h ) from the s ho rt -te rm memo-
r y
- Ave rag e consump tion in MP G
(l/100 km)
from the s ho rt- term memo ry
- Ave rage spe ed in mph (km/h) from the
s h ort-term memo ry -
Distance driven in mi les (km) from the
short-te rm memory
- Curren t fu el cons umption in MPG
(L/1 00
km)
- Shor t-te rm memory overview
- Long-te rm mem ory ove rview
The short -te rm mem ory collects dr iv in g inf or­
mation from the time the ig nitio n is swi tched
o n until it is switched off . If you continu e driv­
i ng withi n two ho urs a fter sw itch ing the ig ni­
t io n off , the new values are incl uded when cal­
c ul ating the c urrent trip inform ation .
Un like the sho rt-term m emory, the long-t erm
memo ry i s not erase d autom atically . You can
se le ct t he time period for eva luating trip in­
f ormation yourse lf.
Fo r some vehicle f unct ions, you can access the
t rip informa tion from t he tempo rary mem ory
i n the line@~
page 22, fig . 5.
Fuel consumption
The current fue l cons umption can be d is ­
played us ing a ba r
~fig . 8. The ave rage con­
s u mption (mpg) stor ed in th e sho rt-t erm
m emo ry is a lso displayed. When the ba r tu rns
green, y our veh icle saves fue l by one of the
f ol low ing functions:
- Recuperation : When the vehicle is coast ing
o r driving down hill, elec trica l energy can be
s tor ed in the b attery . Th e ba r will move t o­
ward
0 .
-Cylinder on demand Sy stem* : when the de­
mand for power is low and other con diti ons
are met, the engine automatically deacti ­
vates fo ur cylin ders . Th e d river a nd passen­
gers will not even notice this. The message
4 cylinde r mode appears under the bar. The
cylinders switch on again w hen more power
is ne eded .
@ Tips
Fuel consumptions (average and current),
r ange and spee d are disp layed i n metric
u nits on Canadian models.

26 Instruments and warning/indicator lights
Lower odometer
The lower odometer shows the total number
of miles (kilometers) driven.
Malfunction message
If there is a malfunction in the instrument
cluster,
DEF will appear in the trip odometer
display area. Contact your authorized Audi
dealer to have the problem corrected.
Time and date display
Fig. 12 Instrument cluster : cloc k and date
You can set the time and the date display in
the MMI. Refer to the MMI owner's manual
for instructions .
When you open the driver's door, the date and
time appear in the instrument cluster display
for 30 seconds.
Service interval display
The service interval display reminds you when
your next service is due.
Fig. 13 In strum ent cluste r: Serv ic e inte rval d isp lay
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed
accordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
switch the ignition on
¢ fig. 13.
After about 5 seconds the display switches
back to normal. The distance and time re­
maining are updated each time the ignition is
switched on until the date due for service is
reached.
Service due
When the due date for service is reached, the
message
Service due! appears in the instru­
ment cluster immediately after you switch the
ignition on. Additionally, a warning tone
sounds. After about 5 seconds the display
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
the service interval display in the car menu.
Select the
ICARI function button > (Car)* sys­
tems control button > Servicing & checks >
Service interval displays .
Resetting the service interval display
Your authorized Audi dealer w ill reset the cor­
responding service schedule after performing
the appropriate service on your vehicle. You
also have the possibility to reset the oil
change schedule after having performed an
oil change according to Audi specifications .
Select the
ICARI function button > (Car)* sys­
tems control button > Servicing & checks >
Service Intervals> Reset oil change interval.
Q) Note
-Only reset the oil change display when
you have completed an oil change.
- If you disconnect the battery terminals,
no calculations can be made for the serv­
ice interval display during this time and
no service reminder will appear. Remem­
ber that observing the proper service in­
tervals is vitally important to extending
the life of your vehicle, particularly the
ll>-