open hood AUDI RS7 SPORTBACK 2015 Owners Manual

10 Instruments and warning/indicator lights
Instruments and warning/indicator Lights
Instruments
Instrument cluster and controls
The instrument cluster is your central source of information.
Fig. 3 Overv iew of the inst rument cluster
CD Coolant temperature gauge ...
@ Tachometer (engine rev counter)
@ Turn signals ........... .. .. .
© Display with
- Driver information system .. .
- Warning/ind icator lights
® Tachometer 10
11
46
22
11
@ Fuel
gauge . . . . . . . . . . . . . . . . . 11
@ Tips
The instrument illumination (for dials and
needles) turns on when the ignition is on
and the vehicle lights are turned off . As
the daylight fades, the illumination of the
dia ls likewise dims automatically and will
go out completely when the outside light
is very low. This feature is meant to rem ind
you to switch on the headlights when out­
side light conditions become poor.
Engine coolant temperature gauge
The engine coolant gauge CD c:> page 10, fig. 3
only works when the ignition is on . To prevent
damage to your engine, please note the fol­
l owing important points:
Engine cold
,.._ N
9 (!)
" a,
If only the LEDs at the bottom of the gauge
turn on, the engine has not reached operating
temperature yet. Avoid high engine speeds, heavy engine loads and heavy th rottle applica­
t ions.
Normal temperature
The engine has reached its operating temper­
ature once the LEDs up to the center of the
gauge turn on unde r normal driv ing cond i­
t ions . Th e LEDs higher up may turn on when
the engine is under heavy load or the exterior
temperature is high. This is no need to worry
as long as the . warning light in the instru­
ment cluster does not illum inate . If the LEDs
in the upper area of the disp lay and the indica­
tor light . in the instrument cluster display
turn on, the coolant temperature is too high
c:> page 15.
A WARNING
-Always observe the warn ing in
c:> page 211, before opening the hood
and checking the engine coolant level.

M N
0:: <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Instrument s and warnin g/indic ator ligh ts 11
- Never open the engine hood if you see or
hear steam, or if you see engine coolant
dr ipping from the engine compartment.
You could burn yourself . Let the engine
cool off first until you can no longer see
or hear steam or coo lant escaping.
Q) Note
- Mount ing additional lights or accessories
i n front of the a ir inlets reduces the cool­
i ng effect of the rad iator . At h igh outside
temperatures or high eng ine load, the
engine could overheat.
- The front spo ile r has been designed to
proper ly distribute the cooling air wh en
t h e veh icle i s moving.
If the spoiler is
damaged, this cou ld red uce the cooling
effect and the engine co uld then over ­
heat . Ask yo ur authorized Audi dea ler fo r
ass istance.
Tachometer (engine rev counter)
The tachometer indicates the engine RPM
(revolutions per minutes).
If engine R PM drops be low 1 ,500, you should
downshift to the next lower gea r. T he red area
at the end of the sca le indicates maximum
pe rmissib le engine RPM after the break- in pe­
riod. Before reach ing this area, move these­
lector lever to position 0/5 (Drive) or ease
your foot off the accelerator peda l.
(D Note
The tachometer needle should only br iefly
be in the red zone: you cou ld damage your
eng ine! The beginn ing of the red zone var­
ies depending on the operati ng tempera­
ture of the eng ine .
@ For the sake of the environment
Upshift ing early saves fuel and reduces en­
gine noise.
@ Tips
The engine speed is limited when the en­
g ine is co ld - the full engine output is not ava
ilable . When the engine is at operating
temperature, the red area in the tachome­
ter moves to a higher RPM range.
Fuel gauge
The fuel gauge only works when the ignition is
on. If the fue l level drops below 2 .6 gallons
(10 lite rs), the bottom LED turns red and the
indicato r light
(j) turns on ¢ page 20. The
bottom L ED blinks red whe n the fuel level is
very low.
The possible range based on the current fuel level is shown in tab@¢
page 22, fig. 4.
(D Note
Neve r run the ta nk completely dry. A n ir­
r egular supply of f uel can cause engine
misfiring and fuel could enter the exha ust
system. The catalytic co nve rter could t hen
ove rheat and be damaged .
Warning/indicator
Lights
Description
The ind icator lights in the instrument cluster
blink or tur n on. They indica te f unct ions or
malfunctions ¢
&.
Messages may appea r with some indicato r
li ghts. A warning signal will sound at t he
same t ime . The indica to r li ghts and messages
i n the center of the displays may be rep lace d
by other disp lays. To show them again, select
the tab for ind icator lights and messages us­
ing the multif unction steering whee l
¢
page 22. If there are several malfunc­
tions, you can display them one at a time us­ i ng the thumbwheel.
Some indicators lights in the d isp lay can turn
on in severa l co lors.
A WARNING
- Failure to heed warning lights and other
important vehicle informat ion may resu lt
IJI,,

14 Instruments and warning/indicator lights
Adaptive cruise control*
9page 83
Audi act ive lane assist*
~ page 91
High beam
Qpage46
BRAKE/( ©) Brake system
The light illuminates when the ignition is
switched on. It goes out after the engine has
been started . Th is indicates that the brake
warn ing light is functioning properly.
If the brake warning light does not light up
when the engine is cranking , there may be a
malfunction in the electrical system. In this
case, contact your Audi dealer.
If the brake system warning/indicator light
turns on, there is a brake system malfunction .
• (USA models) ta (Canada models) Stop
vehicle and check brake fluid level
If the indicator light turns on and the mes­
sage appears, proceed as follows :
"" Pull off the road .
.. Stop the vehicle.
""Turn off the engine .
""C heck the brake fluid level ¢
page 220.
""Contact your neares t authorized repair fa-
cility if necessary.
Warning! Fault in brake system. Contact
dealer
If the ABS indicator light rJlm (USA models)/
[iJ (Canada models), the ESC indicator light
G1 and the b rake system indicator light
• (USA models)/. (Canada models) turn
on and the message appears, the ABS, ESC
and braking distribution are not working ¢
A.
Ca refully drive to your authorized Aud i dealer
immediately to have the malfunction correct­
ed ¢
,A.
• (USA models)/ . (Canada models) Park­
ing brake : system fault! Please contact deal­
er
- If the indicator light and the message ap ­
pear
when stationary or after switching the
ignition on ,
check if you can re lease the
parking brake. After releasing the parking
brake, carefully drive to your authorized
Aud i dea ler immediately to have the mal ­
fu nction corrected. If you cannot release the
park ing brake, seek professiona l assistance.
- If the ind icator light and the message ap­
pear
while driving , the emergency brak ing
function may not be available . It may not be
possible to set the park ing brake or release
it once it has been set. Seek profess iona l as­
sis tance.
(USA models) : If the warn ing light. and the
warning light
E+J appear together, immedi­
ately contact your au tho rized Aud i dealer or
qualified wo rkshop to have all brake pads in­
spected
¢ page 19 .
When the light comes on, an aud ible warning
s ignal is also g iven .
_& WARNING
-Always observe the warnings in
¢
page 211, before opening the hood
and checking the brake fluid .
- Driving with low brake fluid is a safety
hazard. Stop the car and get professiona l
assistance.
- If the. (USA models)/ . (Canada
models) brake system indicator light
turns on togethe r with the ABS and ESC
indicator lights, the ABS/ESC regulating
function may have failed. Functions that
stabilize the vehicle are no longer availa­
ble. This could cause the vehicle to
swerve and increase the r isk of slid ing .
Drive carefully to the nearest authorized
Aud i dealer or other qualified workshop
and have the ma lfunction corrected.
- If the brake wa rning/ind icator light does
not go out after a few seconds and the pa rking brake is re leased, or lights up
while you are dr iving, the f lu id l eve l in
the brake fluid reservoir is too low. If you
believe that it is safe to do so, proceed
Iii>

M N
0:: <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Instrument s and warnin g/indic ator ligh ts 15
immediately at low speed to the nearest
authorized Audi dealer or qualified repair
facility and have the brake system in­
spected .
- Always keep in m ind that after several
brake applicat ions, you will need greater
pressure on the brake pedal to stop your
vehicle . Do not rely on stra ined brakes to
respond w ith maximum stopp ing power
in critical situations. You must allow for
increased bra king distances . The extra
distance used up by fading brakes could
lead to an accident .
PARK!<®> Electromechanical parking brake
The warning/indicator light monitors the
electromechanical parking brake.
If the indicator light . (USA models)/ .
(Canada models) tu rns on, the par king b rake
was set .
• (USA mod els ) ~ (C anada mode ls) Cau­
tion: V ehicle pa rk e d too stee p
If the indicator lig ht blinks and the message
appears, there is not enough braking power to
keep the vehicle from rolling. The brakes have
overheated . The vehicle could ro ll away even
on a small in cl ine.
Pr ess brake pedal to rel eas e parking brake
To release the parking brake, press the brake
pedal and press the button ~ or start driving
with s tart ing ass ist at the same t ime
c::> page 78.
Please release parking brake
To release the parking brake man ually, press
the brake pedal and press the button~ at the
same time. The parking brake on ly re leases
automatically if the driver's safety be lt is fas­
tened.
Ill Parkin g brake!
If the Ill indica tor l igh t turns on and this
message appea rs, there is a p arking brake
mal function . Drive to your authorized Audi dealer or qualified workshop immediately to
have the malfunction corrected
.
_L Engine cooling system malfunction
A malfunction in the engine cooling system
must be repaired as soon as possible .
• Swit ch off en gin e and check coolant l evel
If the indicato r light turns on and the mes­
sage appea rs, the coolant temperature is too
high or the coolant leve l is too low.
.,. Pull off the road .
.,. Stop the vehicle .
.,. Turn off the engine .
.,. Check coolant level
c::> page 217 .
.,. Add coo lant if necessary c::> page 218.
.,. Con tinue dr iv ing on ly afte r the engine cool ­
ant warning/indicator ligh t goes out .
.,. Contact yo ur authorized Audi dealer for as-
sistance if necessary.
If the engine coo lant level is correct, t hen the
radiator fan may be the ca use of the malfunc­
tion .
• Coola nt temperature t oo high! Plea se let
engine run with vehicle stationary
If the indicator light turns on and the mes­
sage appea rs, let the engi ne run at idle for a
f ew m in utes to cool down.
A WARNING
- If you r vehicle should brea k down for
mechanical or other reasons, park at a
safe distance from moving traffic, turn
off the eng ine and turn on the hazard
warn ing lights
c::> page 45, Emergency
flasher.
-
- Never open the hood if you see or hear
steam or coolant escaping from the en­
gine compartment -you risk being scald­
ed . Wait unt il you can no longer see o r
hea r steam o r coolant escap ing .
- The engine compartment of any vehicle is a dangerous area . Before you perform
any wo rk in the engine compartment,
~

"' N
a:: I.J "". rl I.O
"' rl
"' rl
Instrument s and warning /indicator lights 23
® ®
Tab Content
2 Indicator lights and messages
Warning when a door, the hood or
the rear lid is not closed
Service interval display<=>
page 26
Speed warning system <=> page 78
3 Night vision assistant* <=> page 99
4 Audio/video
5 Telephone*
6 Navigation*
The second and third tabs are only visib le if at
l east one indicator light or message is shown
or if that system is switched on .
The status line © is located in the bottom
part of the display¢
fig. 4. It displays the ex­
terior temperature, time, selector lever posi­
tion, trip odometer and odometer .
F or some veh icle functions, you can access the
trip information from the temporary memory
<=> page 24 in the line(!)<=> fig. 5.
A WARNING 1= -
- Never rely exclusively on the outside
temperature display to determine if a
road surface is icy or not. Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice covered and
slippery even at an outside temperature above
41 °F (+5 °().
- Always reduce your speed and dr ive with
special care in cold weather conditions
when the chance of encountering icy
road surfaces increases.
@ Tips
-If the vehicle is stationary, or if you are
driving at a very low speed, the tempera­
ture shown in the display might be
s light ly higher than the actual outside
temperature. This is caused by the heat
being radiated from the eng ine.
- You can select the units used for temper­
ature, speed and other measurements in
the MMI. -
For information on the audio/video and
navigation* functions, refer to the sepa­
rate MMI owner's manua l.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering
wheel.
Fig. 6 Multifunction steering wheel: operating the driv­
er in formation system
Fig. 7 Driver informat ion system: opening the vehicle
func tions menu
Operating concept
.,. Switch the ignition on.
.,. To switch between the tabs, press the rocker
switch
(D to the left or rig ht <=> fig. 6.
.,. To access additional information below or
above, rotate the t humbwheel @down or
up.
.,. To confirm a selection, press the thumb ­
wheel @.
.,. Press the~ button @ to open a submenu
for an active tab.
.,. Press the button@) to access a function for
the prog rammab le steering whee l button* .
Accessing Vehicle functions
.,. Select the first tab with the rocker switch
(D.

M N
0:: <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
for another vehicle or a transponder is
l ocated on the key ring.
- For Decla ration of Compliance to United
States FCC and Industry Canada regula­
tions
¢ page 285.
Power locking system
General description
The power locking system locks or unlocks all
doors and the rear lid simultaneously.
You can lock and un lock the vehicle centrally.
You have the following choices:
- Remote master key¢
page 34,
-Door handles with convenience key*
¢page 35 ,
-Lock cylinder at the driver's door
¢ page 36, or
- Power locking switch inside¢
page 36.
Selective unlocking
When you lock the vehicle, the power locking
system w ill lock the doors and the rear lid.
When unlocking, you can set in the M MI
whether only the driver 's doo r or the entire
vehicle should be unlocked
¢ page 34.
Automatic locking
The automat ic locking feature locks all the ve­
hicle doors and the rear lid when you drive
faster than 9 mph ( 1S km/h).
T he car is unlocked again, when the opening
function in the power lock ing system sw itch
or at one of the door levers is actuated . Th e
Auto Lock function can be turned on and off in
the MMI
¢page 34.
Anti-theft alarm warning system
If the anti-theft alarm warning system de­
tects a break- in into the vehicle, acoustic and
visua l warning signals are triggered.
The anti-theft warning system is activated au­
tomatically when you lock the vehicle . It is de ­
activated when u nlocking using the remote
key, with the mechanical key, and when you
switch the ignition o n.
Opening and clo sin g 33
The alarm also turns off when the a larm cycle
has expired.
Turn signals
When you unlock the veh icle, the turn s ignals
flash twice. When you lock the veh icle the
tu rn s ignals flash once. If they do not flash,
one of the doors, the rear lid or the hood is
not locked.
Unintentionally locking yourself out
In the follow ing cases there safeguards to
prevent yo u lock ing your remote master key in
the vehicle:
- The vehicle does not lock w ith the central
locking switch¢
page 36 if the driver's
door is open.
- On veh icles with convenience key*, if the
most recently used maste r key is in the lug­
gage compartment, the rear lid is a utomat i­
cally un locked again after it is closed.
Do not lock your veh icle w ith the
remote mas­
ter key or convenience key*
unti l all doors
and the rear lid are closed . In this way you
avoid locking yoursel f out accidentally .
Power side door closer*
The vehicle doors are equipped w ith a power
s ide door closer . When closing a door, you on­
ly have to let it fall light ly into the latch. The
door will then automatically close by itself
¢_&. .
A WARNING
-When you lock your vehicle from outside,
nobody -especia lly children -shou ld re­
main inside the vehicle. Remember,
when you lock the vehicle from the out­ side the windows cannot be opened from
the inside.
- When you leave the veh icle, always take
the ignition key w ith you . Th is w ill pre­
vent passengers (children, for example)
from accidentally being locked in the ve­
hicle should they accidentally press the
power locking sw itch in the doors. .,.

M N
0:: <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
~ Press button t'fJ (@ ) to lock the vehicle q .&.
in General description on page 33.
~ Press button c:s <© ) briefly to un lock the
rear lid.
~ Push the red IPANICI button( @) to activate
the panic function. The horn sounds and the
turn signals flash. Push the red
I PANIC ! but­
ton aga in to deactivate the panic function.
If the vehicle is unlocked and no door, the rear
lid or the hood is opened within 60 seconds,
the vehicle locks itself agai n automatically .
This feature p revents t he ve hicl e from be ing
accidenta lly left unlocked over a long period
of t ime.
It depends o n the settings i n the MMI wheth­
e r the entire veh icle is unlocked or on ly cer­
tain doors ¢
page 34.
A WARNING
Read and follow all WARNINGS¢ &. in
General description on page 33.
(D Tips
- In o rder to make sure the locking func­
tion is working, you s hou ld always keep
you r eye on the vehicle to make sure it is
proper ly locked.
-
- Do not use t he remo te control if you are
i nside the car, otherwise you may unin­
tentiona lly lock the ve hicle, and then yo u
would set
off the anti-theft alarm w hen
you try to start the engine or open a
door. In case this happens anyhow, push
the unlock button
0.
- The vehicle can only be locked when the
se lector lever is in the P posit ion.
- Use the panic function only i f you are in
an emergency situation.
Opening and clo sin g 35
Locking and unlocking with convenience
key
Applies to veh icles: w ith conven ience key
Th e doors and th e rear lid can be unlocked
and locked without operating the master key.
Fi g. 24 Convenience key: Lock ing the vehicle
Unlocking vehicle
~ Take ho ld of the door handle. The door is un -
locked automatically .
~ Pull the handle to open the door.
Locking vehicle
~ Select the P se lec to r lever posit ion. Othe r­
w ise the vehicle canno t be loc ked.
~ To lock the veh icle, close the doo r and touch
the senso r in t he door handle
once ¢ fig. 24 .
Do not reach inside the door handle.
T he vehicle can be locked and un locked at any
door . The master key must be within a range
of about 1.5 m from the appropriate door or
the rear lid. It makes no difference whether
the master key is in your jacket pocket or in
your brief case.
It is not possib le to re-open the door for a
brief period directly after closing it. This al­
lows you to ensure that the doors are proper ly
locked.
It depends on t he settings in the MMI wheth­
er the ent ire vehicle is unlocked or one of the
doors ¢
page 34.
A WARNING
Read and follow all WARNINGS ¢&. in
General description on page 33.
-

50 Clear vis ion
Wiper servi ce po sition /blade rep lacem ent
po sit ion
• Switch the ignition off and move the wind­
shield wiper lever to position @¢
page 48,
fig. 47. The windshield wipers move into the
service position.
• To bring the wipers back into the original
pos ition, switch the ignition on and press
the windshie ld wiper lever.
You can also turn the service position on or
off
in the MMI:
• Switch the w indshield wipers off (posit ion
@ ¢page 48, fig. 47).
• Se lect: I CAR I funct ion button> (C ar)* sys·
tern s
control button > Servicing & ch eck s >
Wip er serv ice po sition > O n/ Off .
R em oving the wip er blade
• Lift the w indshield wiper arm up from the
wi ndshield.
• Press the locking knob
(D ~ fig. 48 on the
wiper blade. Hold t he wiper blade firm ly.
• Remove the wiper blade in the direction of
the arrow .
Attaching th e wiper blade
• Install the new wipe r blade in the retaine r
on the w iper arm @until you hear it cl ick in­
to place on the wiper arm.
• Place the wiper arm back on the windshie ld .
• Turn the service pos ition
off .
A WARNING
-
For your safety, yo u should replace the
wiper blades once or tw ice a year. See your
authorized Audi dealer for rep lacement
blades.
(D Note
- The windshield wiper blades must on ly
be folded away when in the service posi­
tion! Otherwise, you risk damaging the paint on the hood or the w indshield wip·
er moto r.
- You should not
move your vehicle or
press the w indshield w iper lever when
the wip er arms are folded away from the w
indshield. The windshield wipers wou ld
move back into their original position
and co uld damage the hood and wind­
shield.
- To help prevent damage to the wiper sys­
tem, always loosen blades wh ich are fro­
zen to the windshield before operating
w ipers.
- To help prevent damage to wiper blades,
do not use gasoline, kerosene, paint
thinner, or other solvents on o r near the
w iper blades.
- To help prevent damage to the wiper
arms or other components, do not at­
tempt to move the wipe rs by hand.
¢j) Tips
- Commercial hot waxes applied by auto·
matic car washes affect the cleanability
of the windshie ld.
- You can also use the se rvice position, for
example, if you want to protect the
w indshield from icing by using a cover.
- You can not activate the service position
when the hood is open .
Mirrors
Adjusting the exterior mirrors
Fig. 49 Fo rward section of driver 's arm rest: power mir·
ror controls
Turn the knob to the desired posit ion :
Q/P -In this pos ition, yo u can adjust the
driver's and front passenger's exterior mirrors
by turning the knob in the desired direction.
4iil -The m irrors are heated depend ing on the
outside tempera ture. .,._

106 Automatic Tran sm iss ion
activate the parking brake and move the
selector lever to P.
- Power is sti ll transmitted to the whee ls
when the engine is running at idle. To
prevent the vehicle from "creeping", you
must keep your foot on the brake when
the engine is runn ing and the selector
lever is in D/S or R or "tiptronic" mode is
selected.
- Do not press the accelerator pedal when changing the selector lever pos ition
wh ile the vehicle is stat ionary and the
eng ine is running.
- Never shift into
R or P wh ile driving.
- Before driv ing down a steep slope, re-
duce your speed and shift into a lower
gear with "tip tronic".
- Do not ride the brakes or press the brake
peda l too often or too long when dr iving
down a hill. Constant braking causes the
brakes to ove rheat and s ubstant ially re­
duces braking per formance, increases
braking distance or causes comp lete fail ­
ure of the brake system.
- To prevent the veh icle from rolling back
when stopping on inclines, a lways hold it
in place with the brake peda l o r parking
brake.
- Never hold the ve hicle on an incl ine with
a slipping clutch . The clutch opens auto­
matically when it becomes too hot from
the overload. An indicator lamp
ml illu­
minates and a dr iver message appears
¢ page 1O7when the clutch is overload­
ed.
- If the engine must remain running, never
hav e any driv ing pos ition engaged when
c heck ing under the hood . M ake sure the
selector lever has securely engaged and
is locke d in P with the parking brake se t
¢page 211. Otherwise, any increase in
engine speed may set the vehicle in mo­
t ion, eve n with the park ing brake ap­
plied.
Qd) Note
- When stopping on an incline, do not try to hol d the vehicle in place by pressing the acce
lerator pedal while a d riving gear
is se lected. This can cause the transmis­
sion to ove rheat and can damage it. Acti­
vate the parking brake or press the brake peda l to prevent the vehicle from rolling.
- Allowing the vehicle to ro ll when the en­
gine is stopped and the selector lever is
in N will damage the transmission be­
cause it is not lubricated under those cir­
cumstances .
(D Tips
For safety reasons, the parking brake is re­
leased automatically only when t he driv­
er's safety belt is engaged in the buckle.
Hill descent control
The hill descent control system assists the
driver when driving down declines .
Hill descent control is activated when these­
lector lever is in D/S and you press the brake
pedal. The transmission automatically selects
a gear that is suitable fo r the incline . H ill de­
scent cont ro l tries to ma inta in the speed ach­
ieved a t the time o f braking, with in phys ica l
and tec hni cal lim it a tions. If may st ill be nec ­
essary to ad just the speed with the brakes.
Hill descent contro l sw itches off once the de­
cl in e leve ls o ut o r yo u press the a cce le rato r
peda l.
On vehicles with the cru ise cont ro l system*
~ page 79, hill descent control is also activat­
ed whe n the speed is set.
A WARNING
-
Hill desce nt cont ro l cannot overcome
physical lim itations, so it may not be a ble
to maintain a constant speed unde r a ll
conditions. A lways be ready to apply the
brakes .

184 Audi pre sense
Audi pre sense
Preventative passenger
protection
A pp lies to veh icles: with Audi pre se nse
Audi pre sense can initiate steps to help pro­
tect vehicle occupants in certain situations.
The functions described depend on equ ipment
installed in your vehicle:
Audi pre sense basic*
The following functions can be triggered in
certain driving situations:
- Tightening of the safety belts (for example,
during heavy braking) : the front safety belts
have reversible belt pretensioners. If a colli­
sion does not occur, the safety belts loosen
slightly and are ready to be tightened again.
- Closing the windows and the sunroof*: the
windows and the sunroof* close leaving a
small open gap.
Audi pre sense basic functions can be trig­
gered at speeds above 20 mph (30 km/h).
Vehicles with Aud i drive select*: the deploy­
ment time is adapted in
Dynamic mode.
Audi pre sense front (vehicles with
adaptive cruise control*)
Audi pre sense front includes the functions in
Audi pre sense basic. In addition, within the
limits of the system, the likelihood of a colli ­
sion with the vehicle immediately ahead is al­
so calculated . If the system senses an immi­
nent collision the following functions can be
tr iggered :
- Braking guard c::>poge
87
-Tightening the safety be lts
- Closing the windows and the sunroof* (leav -
ing a small open gap)
Audi pre sense rear (vehicles with Audi
side assist*)
Audi pre sense rear includes the functions in
Audi pre sense basic. In addition, the likeli­
hood of a rear-end collision with the vehicle
coming from behind is also calcu lated.
If the risk
of a co llision is detected, the following
functions can be triggered:
- Tig htening the safety belts
- Closing the windows and the sunroof* (leav-
ing a small open gap)
Audi pre sense plus*
Audi pre sense plus includes the functions in
Audi pre sense front and Audi pre sense rear.
Error message
Audi pre sense: not available
Preventative passenger protection is not avail­
able. See your authorized Audi dealer immedi­
ately to have the malfunction corrected.
_& WARNING
-=
Audi pre sense cannot overcome the laws
of physics. It cannot prevent a collision. Do
not let the increased safety provided
tempt you to take risks. This will increase
the r isk of a collis ion and serious personal
in juries .
- The sensors cannot always detect all ob­
jects. This increases the risk of a colli­
s10n.
-Aud i pre sense does not detect people or
an im als or objects that are crossing the
veh icle's path c::> page
81.
-The radar sensor's vis ion can be reduced
by heavy rain, ice, snow, heavy road sp ray
and reflections from guard rails, tunnel
entrances, etc. These and similar condi­
tions can prevent vehicles from being ac ­
curately detected and in some cases they
may not be detected at all.
(D Note
The sensors can be displaced by impacts or
damage to the bumper, wheel housing and
underbody. This can affect the function of
the Audi pre sense system. Have your au­
thorized Audi dealer check to make sure
that the system is working properly.