AUDI S3 2010 Owners Manual

long waits on red. Turning the engine off for just 30 -40 seconds
saves more f ue l than i s bu rned star ting the engine again.
It takes a long time for the engine to warm up fully when it is
running at idle. However , wear and noxious em issions are especial ly
h ig h w hen the eng ine is warming up. So y ou should dr ive away as
soon as you start the engine and avoid running at high RPMs whi le
the eng ine is still warming up.
0 Note
Do not leave en gine idling unattended after starting. If warn ing
lights should come on to indicate improper operation, they would
go unheeded . Extended idling also produces heat, wh ich cou ld
result in overheating or other damage to the vehicle or other
property .
Regular maintenance
A badly tuned engine unnecessarily wastes a lot of fuel.
- Have your vehicle serviced at regu lar intervals.
By having your vehicle regu lar ly serviced by an authorized Audi
dea ler he lps to ensure that it runs properly and econo mically . The
condition of your vehicle not only affects its safety and abi lity to
hold i ts va lue, it a lso affects fuel consumpt ion .
Che ck yo ur oil ea ch t ime you fill your t ank.
T he amount of oil used is related to engine load and speed.
It is nor mal for the oil consumption of a new engine to reach its
lowest va lue after a certain mi leage has been driven.
You must drive your vehicle about 3,000 mi les (5,000 kilometers)
before you can proper ly assess oil consumption .
T his also applies to fuel consumption and engine output.
Controls and equip­ ment Safety first Vehicle operation
Dri
ving and environm ent
0 Note
• Have your vehicle maintained properly and in accordance with
the service recommendations in your Warranty
& Maintenance
booklet. Lack of proper maintenance as we ll as improper use of the
vehic le wi ll impair the function of the emission control system and
cou ld lead to damage .
• Do not alter or remove any component of the Emission Control
System unless approved by the manufacturer .
• Do not alter or remove any device, such as heat shields,
sw itches, ignition wires, valves, which are designed to protect your
vehic le's Emission Control System and other important vehicle
components. •
Fewer short trips
Fuel consump tion will always be relatively hi gh on shor t
trips.
- Try to avo id driving short dista nces wi th a cold en gine.
The engine and cata lytic c onverter have to reach their optima l oper ­
ating temperature to reduce fuel consumption and noxious emis ­
sions effective ly .
• Just after starting, a cold engine in a mid-size car burns the fuel
at a poor rate of 6 -8 miles per gallon (30 -40 11100km). Half a mi le
down the road, the mileage improves to 12 MPG (20 1/100 km). It wi ll
take the engine no less than
two and a half miles (4 km) of driving to
warm up to its proper operat ing temperature and operate at a n
economic mileage . This exp lains why taking the car for short trips is
a ra ther waste ful convenience .
• The outs ide temperat ure is also critical in this regard. Your car
consumes more fuel in the winter than in the summer .•
Vehicle care Do-it-yourself service Technical data

___ T_ r _a_ il_e _r_ t_ o_ vv_ in__... g,_ __________________________________________________ _
Trailer towing
Driving with a trailer
General information
Your Audi was designed primarily for passenger transpor­
tation.
If you plan to tow a trailer, please remember that the additional load
wi ll affect durability, economy and performance.
Trai ler towing not on ly p laces more stress on the vehicle, it a lso ca lls
for more concentration from the driver.
For this reasons, always fo llow the operating and driving instruc ­
tions provided and use common sense. •
Technical requirements
Traile r hit ch
Use a weight -carrying hitch conforming to the gross trailer weight.
The hitch must be suitab le for your vehicle and tra iler and must be
mounted secure ly on the vehicle's chassis at a
technically sound
location . Use only a trailer hitch w ith removable ball mount. A lways
check with the trai ler hitch manufacturer to make sure that you are
using the correct hitch .
Do not use a bumper hit ch .
The hitch must be installed in such a way that it does not interfere
w ith the impact-absorbing bumper system . No modifications
should be made to the vehicle exhaust and brake systems. From
time to time, check that all hitch mount ing bolts remain securely
fastened.
When you are not towing a trailer, remove the trailer hitch ball
mount. This prevents the hitch from causing damage should your
vehic le be struck from behind
=:> & .
Tire pre ssure
When towing a trailer, inflate the tires of your vehic le to the cold tire
pressure listed under "Full load"on the sticker on the right door­
jamb. Inflate trai ler tires to trai ler and tire manufacturers' specifica ­
tions.
Lights
The head ligh t settings should be checked wit h the trai ler attached
before driving off. Have the head lights adjusted as necessary so
t hat you can see the road ahead but not blind oncoming traffic.
Check to make sure both vehicle and trailer lights are working prop ­
erly.
Engin e cool ing sy stem
Towing a t rai ler makes the engine wo rk ha rder . It is important that
the cooling system's performance stands up to the additiona l
strain. Make sure that the coo ling syste m has enoug h fluid.
Traile r br akes
If your traile r is equipped wi th a braking system, check to be sure
that it conforms to al l regu lations.
T he trailer hydraulic brake system must not be directly connected to
the vehic le's hydrau lic brake sys tem.
Safety chai ns
Be sure trailer safety chains are properly connected from the trailer
to the h itch on the vehicle. Leave enough slack in the chains to
permit turning corners. When you install safety chains, make sure
they will not drag on the road when you are driving.
The chains should cross under the trailer tongue to prevent it from
dropping in case of separation from the hitch. _.

Trailer lights
Trailer lights must meet all regulations. Be sure to check with your
authorized Audi dealer for correct wiring, switches and relays.
Mirrors
If you are unable to see the traffic behind you using the regular
outside mirrors, then you
must install extended mirrors. It is impor­
tant that you
always have clear vision to the rear .
& WARNING
After removing the trailer hitch, do not store it in your vehicle. In
case of sudden braking, the hitch could fly forward and injure you
or your passengers .
.1
Operating instructions
Maximum trailer weight
A trailer for your vehicle is limited to a typical class 1 or class 2
trailer.
Trailer load distribution
Be sure the load in the trailer is held securely in place to guard
against shifting, be it forward, backward or sideways.
Never allow a passenger to ride in a trailer:::::, & in "Driving instruc­
tions".
Tire pressure
When towing a trailer, inflate the tires of your vehicle to the cold tire
pressure listed under "Full load" on the sticker on the right door­
jamb. Inflate trailer tires to trailer and tire manufacturers' specifica­
tions.
Controls and equip­ ment Safety first Vehicle operation
Trailer towing
Lights
The
headlight settings should be checked with the trailer attached
before driving off. Adjust as necessary so that you can see the road
ahead but not blind oncoming traffic.
Check proper working of vehicle and trailer lights.
Safety chains
Be sure trailer safety chains are properly connected from the trailer
to the hitch on the vehicle. Leave enough slack in the chains to
permit turning corners. When you install safety chains, make sure
they will not drag on the road when you are driving.
The chains should cross under the trailer tongue to prevent it from
dropping in case of separation from the hitch. •
Driving instructions
Driving with a trailer always requires extra care and
consideration.
To obtain the best possible handling of vehicle and trailer,
please note the following:
Do not tow a loaded trailer when your car itself is not
loaded.
- Be especially careful when passing other vehicles.
Observe speed limits.
Do not drive at the maximum permissible speed.
- Always apply brakes early.
Monitor the temperature gauge.
Vehicle care Do-it-yourself service Technical data

___ T_ r _a_ il_e _r_ t_ o_ vv_ in__... g,_ __________________________________________________ _
Weig ht dis tributi on
Towing a loaded trailer with an empty car resu lts in a high ly
unstable distribution of weight . If this cannot be avoided drive at
very low speeds on ly to avoid the risk of losing steering control.
A "ba lanced" rig is easier to operate and control. This means that
the tow vehicle should be loaded to the extent possible and permis ­
sib le while keeping the trai ler as light as possib le under the circum ­
stances. Whenever possible, transfer some cargo to the luggage
compartment of the tow vehicle while observing tongue load requirements and vehicle loading considerations .
Speed
The higher the speed, the more difficult it becomes for the driver to
control the rig . Do not drive at the maximum permissible speed.
Reduce your speed even more under unfavorable load, weather or
wind conditions -particularly when going downhill.
Reduce vehicle speed
imm ed ia tely if the trailer shows the sl ightest
sign of swaying. Do not try to s top the s wayi ng by a ccelerating .
Observe speed limits . In some areas speeds for vehicles towing
trai lers are lower than for regular vehicles.
Always app ly brakes early. When driving downhill, shift into lower
gear to use the engine braking effect to slow down the vehicle. Use
of the brakes alone can cause them to overheat and fail.
C oo la nt tempe ra tu re
The coolant temperature gauge ~ page 9 must be observed care ­
ful ly. If the needle moves close to the upper end of the scale, reduce
speed immediately and/or switch off the air condit ioner.
If the coolant temperature warning light in the instrument cluster
starts flashing -~-, pull off the road, stop and let the engine
idle for
about two minutes to prevent heat build -up .
& WARNING
An yone not p rope rly res train ed in a mo ving vehi cle is a t a mu ch
gre ater risk in a n accident. Neve r let an yone ride in your car who
is not p rop erly we ari ng th e res tra int s pro vide d b y Aud i.
c
Trailer towing tips
Important to know
Your vehicle handles different ly when towing a trailer because of
the additional weight and weight distribution . Safety, performance
and economy w ill great ly depend on how carefu lly you load your
trailer and operate your rig.
Before you actually tow you r trailer, practice turn ing, stopping and
backing up in an area away from traffic. Keep practicing unti l you
have complete ly become familiar with the way your vehicle -trailer
combination behaves and responds .
Backing up is difficult and requires practice. Backing up with a
trailer genera lly requires steering ac tion opposite of that when
backing up your vehicle without a trailer .
Maintain a greater distance between your vehicle and the one in
front of you. You will need more room to stop.
T o compensate for the trailer, you wi ll need a larger than normal
turning radius .
When passing, remember that you cannot accelerate as fast as you n ormal ly wou ld because of the added load . Make su re you have
enough room to pass. After passing, al low plenty of room for your
trailer before changing lanes again .
Avoid jerky starts, sharp turns o r rapid lane changes.

[ i] Tips
• Do not tow a trailer during the break-in period of your vehicle.
• If you tow a trailer, your Audi may require more frequent mainte ­
nance due to the extra load=> page 299 . •
Parking on a slope
-----------------
Do not park with a trailer on a slope. If it cannot be
avoided, do so only after doing the following:
When parking:
-Apply the foot brake.
- Have someone place chocks under both the vehicle and the trailer wheels .
- With chocks in place, slowly release the brakes until
wheel blocks absorb the load.
- Turn the wheels towards the curb.
- Apply the parking brake.
- Place an automatic transmission in
P, respectively a
manual transmission in first or reverse gear.
When restarting after parking:
- Start the engine.
- Shift transmission into gear.
- Release the parking brake and slowly pull out and away from the wheel blocks.
- Stop and have someone retrieve the wheel blocks.
Controls and equip­
ment Safety first Vehicle operation
Trailer towing
[
i] Tips
If you move the selector lever of the automatic transmission to P
before applying the parking brake and before blocking the wheels,
you may have to use more force later to move the lever out of the
P
position .•
Vehicle care Do-it-yourself service Technical data

___ C _l_e _a _ n_ in_g ~_ a_n _ d ___ p ___ r_ o _t _e _c_ t_ i_o _ n _____________________________________________ _
Cleaning and protection
General information
Regular care p rese rves vehicle value .
Any automobile is exposed to industrial fumes, corrosive road salt ,
muddy dog feet, e tc. A wel l cared fo r Audi can look l ike new many
years after purchase . Regu lar and correct care will contribute to
maintaining the beauty and va lue of your Audi .
Furthermo re , g ood care ma y be a conditi on for sub sta ntiating a
warr anty cla im should corro sion damage or paint defect s occur .
Your authorized Audi dealer has a var iety of dedi cat ed vehicle -care
product s
and can advise which ones to use for cleaning the exterior
and interio r of your vehicle.
Whether you use products recommended by Audi or other commer ­
cially availab le cleaning agen ts, please make su re you apply them
correctly .
& WARNING
• Cleaning agents m ay be poi sonou s. Keep them out of the re ach
of childr en.
• Heed all cau tion label s.
• Alway s read direction s on the container before u sing any
produ ct. Follo w the dire ction s carefull y.
• Most chemi cal cle aner s are concentr ated and h ave to be
d iluted .
• Use spot remo ving fl uid s onl y
in well ventila ted are as.
• Do not use gasoline , kero sene , diesel fuel , nail poli sh remover
or other vol atil e fluid s. They may be to xic , fl ammab le or h azardou s
in other wa ys. Do not wa sh , wax or dry the vehicle w ith the igni ­
tion on or the engine ru nning .
& WARNING (continu ed )
• Do not clean the unders ide s of cha ssi s, fenders , wheel cover s,
et c. without pr ote cting y our hands and arm s. You may cut your self
on sh arp-edged metal part s.
• Moisture and i ce on brakes may impair br aking eff icien cy
~ page 191 , "General information ". Test the brake s carefully each
time you wash the vehicle .
'£> For the sake of the environment
Select only environmenta lly friend ly c leaning products. Leftover
clean ing products should not disposed of in the household waste .•
Care of exterior
Washing
F requent washing protects the vehicle.
The best protection against environmental influences is frequent
washing a nd waxing.
How often this is required depends on :
• How much the vehicle is used
• Where the vehicle is parked (garage, in the open under trees ,
etc.)
• The seasonal and weather conditions
• Environmenta l influences
The longer bird droppings, insects, tree resin, road and industrial
gri me, tar, soot, road salt and other materials remain on the vehicle
body , the more lasting their destructive effects will be. .,_

_____________________________________________ C_ l_ e _a_ n_ in_ g_a _ n_d_ p_ r_ o_ t _e_ c_t _io _ n __ _
•
High temperatures, as from exposure to intense sunlight, intens ify
the corrosive effect particularly when humidity is high as well.
Under ce rtain circumstances ,
weekly washing may be necessary .
Under other conditions, a monthly washing and waxing may be
adequate.
After the winter, the
underside of the vehicle should be thoroughly
washed, preferably in a professional car wash.
& WARNING
Always read and heed all WARNINGS and other information
=>
page 204 . •
Automatic car wash
The vehicle can be washed in almost any modern auto­
matic car wash.
The vehicle paint is so durable that the vehicle can normally be
washed without problems in an automatic car wash . However , the
effect on the paint depends to a large extent on the design of the
facility, the filtering of the wash water, the type of wash and care
material, etc. If the paint has a dull appearance after going through
the car wash or is scratched, bring this to the attention of the oper­
ator immediately . If necessary, use a different car wash .
Before going through a car wash, be sure to take the usual precau ­
tions such as closing the windows and panoramic sliding sunroof *.
Remove antenna if applicable.
If you have installed additional accessories on the vehicle -such as
spoilers, roof rack , etc. -it is best to ask the car wash operator if
these should be removed .
& WARNING
Always read and heed all WARNINGS and other information
=> page 204. •
Washing the vehicle by hand
A lot of water is needed when washing a vehicle by hand.
-Before you start washing, make sure you have read and
understood the WARNINGS=:>
& in "General informa ­
tion" on
page 204.
- First soak all dried dirt until it is soft, then rinse it off.
- As you clean your vehicle, start with the roof and work
your way down to the bottom , using a sponge, a sponge
glove or a clean brush.
- Rinse the sponge or the sponge glove often, flushing it
clean each time.
- Use special car shampoo only for very persistent dirt.
- Rinse the car thoroughly with water.
- Use a chamois leather to gently wipe the exterior dry.
Use a separate sponge for cleaning the wheels, door sills and other
regions exposed to road dirt. In this way , you will not scratch the
paint with coarse particles imbedded in the sponge the next time
you wash the car.
& WARNING
• Do not clean the underside of the chassis, fenders, wheel
covers, or other hard to reach parts without protecting your hands
and arms. You may cut yourself on sharp-edged metal parts . .,
Vehicle care
I t •

___ C_ le_ a _ n_i_n ~g _ a_ n_ d __ p_r _o _t _e _c_ t_ i_o _n ___________________________________________ _
& WARN ING (c o ntinu ed )
• Always read and heed all WARNINGS and oth er informat ion
~ page 2 04 .
0 Not e
• Never try to remove dirt, mud or dust if the surface of the vehicle
is dry. Never use a dry cloth or sponge, since this cou ld scratch your
veh ic le's paint or w indows .
• Never wash your car in bright sunlight. Drops of water act as
magnifying lenses and may damage your paint.
• When you wash your car in t he winter : if you rinse your vehic le
with a hose, be careful not to aim the stream of water directly at
locks, or at door or hatch openings -they can freeze shut.
• Never use sponges designed to remove insects, or any kitchen
scouring s ponges or simila r pr oducts. They can damage your paint
finish .
• Never use a dry cloth or sponge to c lean the head ligh ts. O nly use
wet cloths or sponges to prevent scratches . It is best to use soapy
water.
c£, For the sake of the environment
In the interest of the environment, the vehicle shou ld on ly be
washed in specia l wash bays. •
Washing your vehicle with a power washer
Cleaning the exterior of your car wi th a high -p ressure
power washer is safe as l ong as y ou observe a few simple
rules .
-Before us ing the p ower washer, make s ure you have read
and unde rs too d t he WAR NINGS=:>
& in "General in for­
mati on" o n
page 204.
-Always follow the operati ng inst ructions fo r th e pow er
washer.
Make sure that the jet on t he spray hose produces a "fan
sha ped sp ray".
D o
not hold the spray nozzle too close to soft materials.
When cleaning the vehicle with a power washer always follow the
opera ting instructions. Th is appl ies particularly to the
operating
pre ssure
and the spraying distance . Maintain a sufficient distance
t o so ft ma teria ls such as rubber hoses a nd sound/vibrat ion dead ­
ening materia ls (particularly on the underside of the engine hood).
Do not use a jet which sp rays water in a
direct stream o r one tha t
has a
rotating j et.
Water temperature shou ld not exceed 140 °F (60 °Cl.
& WARNING
Never wash tires with a jet that sp ray s water in a dire ct stream .
This could c ause invi sible damage to the tire s and weake n them ,
even if the spray is from a relatively long distan ce and for a short
time . Damaged and weakened tires can fail and cau se ac cident s
a nd person al injury.
0 Note
To avoid damaging your vehic le, always make sure that there is
suffic ient distance between the spray hea d and so ft m ateria ls like
rubber hoses, plastic parts and sound -deadening materials . Never
aim the spray head at the same p oint for a l ong time . This a lso
applies to cleaning head lights and painted bumpers . Remember:
t he c loser the n ozzle is to the surface of the materia l, the greater the
stress on the material. •

_____________________________________________ C_ l_ e _a_ n_ in_ g_a _ n_d_ p_ r_ o_ t _e_ c_t _io _ n __ !II
•
Waxing
Wax prote cts the vehicle's paint.
- Use a manually applied car wax occasion ally to protect
t h e paint.
A good wax coating protects the vehicle paint to a large extent
against the environmental factors listed under~
page 204,
"Washing" and even against slight scratches .
You can use a liquid car wax to protect your paint as soon as one
wee k after you r vehic le has been delivered.
Even if you regularly use a
waxing process in automatic car washes,
we recommend that you manua lly app ly a coat of wax to give the
paint e xtra protection, par ticu lar ly if water no longer beads on the
clean paint.
Protec t plastic body parts with car wax in the same way as the
vehic le body.
During warm weather dead insects tend to col lect on the front
bumpe r and on the forward area of the hood. They are much easie r
to remove from paint that is waxed
often.
& WARNING
Always read and heed all WARNINGS and other information
~ page 204 .
0 Note
Do not use ca r wax on
• matte or anodized meta l trim
• rubber or rubber -like trim. •
Polishing
Polishi ng resto res the gloss to the p aint.
Po lish your vehic le on ly if the paint has lost its shine and the g loss
cann ot be brought back wi th wax .
I f the polish used does not contain preservative compounds, the
paint must be waxed afterwards~
page 207, "Waxing".
& WARNING
Always read and heed all WARNINGS and other information
~ page 204 .
0 Note
Do not treat matte anodized metal trim, plastic or rubber parts with
polish or wax .•
Trim strips
Metal trim needs special c are.
Fo r envi ronmental reasons, Audi fab ricates the bright trim strips
and trim pieces from pure chromium -free aluminum .
Dirt and marks on the trim strips should be removed with a
pH­
balanced
c leaning agent (do no t use a chr ome clean er). Authorized
Audi dea lers carry c leaning products which have been tested for use
on your vehicle and are not harm fu l to the enviro nment .
To avoid corrosion on the exterior trim strips, only a pH -ba lanced
solution shou ld be used for the windshield washer.
& WARNING
Alway s read and heed all WARNINGS and other information
~ page 204 .•
Vehicle care I t •

-~_C_ l_ e _a _n_ in_g=- a _n_d__, p,__ ro_ t_e _c_ t_ i_o _n _____________________________________________ _
Plastic and vinyl
Plastic needs special care.
Use a clean, damp cloth or sponge to remove dust and light surface
dirt. For other soil, use a lukewarm all -purpose cleaning solution or
a mild saddle soap for vinyl trim. Remove water spots and traces of
soap with a clean, damp cloth or sponge . Use a clean, soft cloth to
rub dry .
Grease, tar or oil stains can be removed with a clean cloth or sponge
soaked with all-purpose cleaner or with a solvent designed espe­
cially to clean vinyl.
Occasionally apply a colorless vinyl or leather preservative to retain
the material's luster and pliability.
& WARNING
Always read and heed all WARNINGS and other information
~ page204. •
Aluminum trim
Use only neutral-pH products to remove spots and deposits from
aluminum surfaces. Chrome care products and alkaline cleaners
will attack aluminum surfaces and can damage them over time.
& WARNING
Always read and heed all WARNINGS and other information
~ page204 .•
Touch-up paint
Minor paint damages should be touched up immediately.
-Use either a touch -up paint stick or spray paint to cover
minor scratches and nicks.
Your authorized Audi dealer has touch-up paint for minor scratches
and stone chips. Scratches should be touched up soon after they
occur to prevent corrosion.
If a spot starts to rust, however, a simple touch-up job will not be
enough. The affected surface must be sanded smooth and coated
with an anti-rust primer before the painted finish can be restored.
The number for the original vehicle paint can be found on the
vehicle identification label~
page 294.
& WARNING
Always read and heed all WARNINGS and other information
~ page204.•
Windows
Clear vision to all sides.
Clean all windows regularly to remove road film and
carwash wax buildup.
- Remove snow from windows using a brush.
- Use a plastic ice scraper to remove ice from windows and
mirrors.
- Remove other residue on the windows with a spray-on
glass cleaner.
- Wipe the windows dry with a clean piece of cloth or
kitchen paper towel.