air condition AUDI S3 2010 Owner's Manual

__________________________________________________ A_ i_ r _b _a...; g::- s_ y=--- s_t _e _m __ !II
PASSENGER AIR BAG OFF light
I, Q
--
&I Ii u ,, , u
I I J' J
Fig. 1 42 Sectio n from
t h e ce nte r co nso le :
PA SS ENGER AIR B AG
OFF light
The PA SSENGER AIR BAG OFF light is located in the center console
=>fig.142 .
The
PA SSENGER AIR BAG OFF light wil l come on and stay on to te ll
you when the front Advanced Airbag on the passenger side has been turned off by the electron ic control unit. Each time you turn on
the ign it ion, the
PA SS ENGER AIR BA G OFF light will flash for a few
seconds and:
• will stay on if the front passenger seat is not occupied,
• will stay on if there is a small child or chi ld restraint on the front
passenge r seat,
• will go out if the front passenger seat is occupied by an adult as
registered by the we ight-sensing mat .
T he
PA SS ENGER AIR BAG OFF light mu st co me on and sta y on if the
ign ition is on and
• a car bed has been insta lled on the front seat, or
• a rearward -facing chi ld restraint has been installed on the front
passenger seat, or
• a forwa rd -facing child restra int has been installed on the front
passenger seat, or
• t he we ight registered on the front passenger seat is equa l to or
less than the combined weight of a typica l 1 year -old restrained in
Controls and equip­
ment Safety first
Vehicle operation
one of the rear-facing or forward -facing infant restraints listed in
Federa l Motor Veh icle Safe ty S tandard 208 with which the Advanced
Airbag System in your vehicle was certified.
I f the front passenger seat is not occupied, the front airbag will not
deploy, and the
PA SS ENGER AIR BAG OFF light will stay on . Never
insta ll a rearward -facing child restraint on the front passenger seat,
the sa fest place for a child in any kind of child restraint is at one of
the seating posi tions on the r ear seat =>
page 147, "Child restraints
on the front seat -so me important things to know" and=>
page 167,
"Chi ld Safety ".
If the PASSENGER AIR BAG OFF light com es on when one of the
conditions listed above is met, be sure to check the light regu lar ly
to make certa in that the
PA SS ENGER AIR BAG OFF light stays on
continuously whenever the ignition is on . If the
PA SSENGER AIR
BAG OFF
light does not appear on and does not stay on all the tim e,
stop as soon as it is safe to do so and
• reactivate the system by turning the ignition off and then turning
it on aga in;
• remove and reinstall the child restraint. Make sure that the child
restrain t is proper ly installed and t hat the safety be lt for the front
passenger seat has been correctly routed through the child restraint
as described in the chi ld restraint manufacturer's instructions;
• make sure that the convertible locking feature on the safety belt
for the front passenger sea t has been activated a nd that the safety
belt has been pulled tight . The belt must not be loose or have loops
of slack so that the sensor be low the safety belt latch on the sea t can
do its job =>
page 177.
• make sure that things that may inc rease the we ight of the child
and child safety seat are not being transported on the front
passenger seat;
• make sure that the safety belt tension sensor is not blocked.
Shake the safety belt latch on the front passenger seat back and
forth;
• I f a strap or te ther is being used to tie the child sa fety seat to the
front passenger seat , make sure that it is not so tight that it causes .,
Vehicle care Do-it-yourself service Technical data

_1--_l_ n _t _ e _ll _,ig ,_,_ e_n _t _ t_ e_ c_ h_n _o_ l_ o ~g""- y.e- __________________________________________ _
Intelligent technology
Notice about data recorded by
vehicle control modules
Your vehicle is not equipped with an Event Data Recorder (EDR),
installed by some manufacturers for the express purpose of
capturing data for retrieval after an accident or crash event . EDR's
are sometimes called "crash recorders".
Some state laws restrict the retrieval or downloading of data stored
by EDR's that were insta lled in a vehicle for the express purpose of
retrieving data after an accident or crash event without the owner's
consent .
Although your vehicle is not equipped with an EDR, it is equipped
with a number of electronic control modules for various vehicle systems such as, for example, eng ine function, emission control, as
well as for the airbags and safety belts.
These electronic control modules also record vehic le -related data
during norma l vehicle operation for diagnostic and repair purposes .
The recording capacity of the electronic cont rol modules is limited
to data (no sound is recorded) and only a small amount of data is
actually recorded over a very limited period of time and stored when
a system fault or other condition is sensed by a control unit . Some
of the data then stored may relate to vehic le speed, direction,
braking as we ll as restraint system use and performance in the
event of a crash or other condition. Stored data can only be read and
downloaded with special equip men t.
Electronic Stabilization Program (ESP)
General
The Electronic Stabili ty Program increases driving
stability.
co ::,
_1, _ __ J"u. __ 11 ... _ ,.....u.,___,lli u.. _ .x,u _ _, r-u ~~ ~!' js:..~&c:',I
I
'
1 J
F ig . 15 8 Cente r
cons ole with E SP
sw itch
With ESP, control over the veh ic le is increased in situations when
the vehicle is close to the limits of grip, such as during acce leration
and in curves. ESP reduces the risk of skidding a nd improves vehicle
stability under all road conditions . It operates at all speeds .
The Anti-Lock Brake System (ABS), E lec tronic Differentia l Lock (EDS)
and Anti-Slip Regulation System (ASR) are integrated in the Elec­
tronic Stability Program .
How ESP work s
The ESP control unit processes the fo llowing data from high-sensi ­
tive sensors : the rotational speed of the vehicle about its vertica l
axis, fore -and -aft and lateral acceleration forces, brake pressure and
steering angle.
Using steering ang le and vehicle speed, the direction the driver
wishes to travel is determined and continuously compared with
t,.

-Intelligent technology
---""'------------ ....::....:...:~---------------------------
Brake lining wear status
Brake lining wear may be checked by visual inspection of the condi­
tion of the brake pads through the openings in the wheel. If neces­ sary, the wheel may be removed for this inspection=> page
270,
"Wheel change" .
L1}. WARNING
• You should perform braking maneuvers for the purpose of
cleaning the brake system only if road conditions permit. Other
road users must not be put at risk -you may cause an accident!
• Before descending a steep grade, reduce speed and shift trans­
mission into a lower gear or lower driving range. Do not ride the
brakes or hold the pedal down too long or too often. This could
cause the brakes to get hot and diminish braking efficiency.
• Do not "ride the brakes" by resting your foot on the pedal when
you do not intend to brake. This may cause the brakes to overheat,
premature wear and increased stopping distance.
• Under certain climatic and operating conditions such as
passing through water, driving in heavy rain or after washing the
vehicle, the effectiveness of the brakes can be reduced. In winter,
ice can accumulate on the brake pads, linings, discs and drums.
Carefully apply brakes for a test. Brakes will dry and ice coatings
will be cleaned off after a few careful brake applications.
• Driving for an extended period of time on salt-covered roads
without using your brakes can also affect braking efficiency. Clean
off accumulated salt coating from brake discs and pads with a few
careful brake applications.
• If you damage the front spoiler, or if you install a different
spoiler, be sure the air flow to the front brakes is not obstructed.
Otherwise the brake system could overheat reducing the effective ­
ness of the entire brake system.
• Failure of one brake circuit will impair the braking capability
resulting in an increased stopping distance. Avoid driving the
& WARNING (continued)
vehicle and have it towed to the nearest authorized Audi dealer or
qualified workshop. •
Brake booster
The brake booster adds extra braking power.
The brake booster works with vacuum pressure which is created
only when the engine is running=>& .
L1}. WARNING
• Never let the vehicle roll to a stop with the engine shut off.
• If the brake booster is not working, for example when towing
your vehicle, or because the brake booster has somehow been
damaged, the brake pedal must be pressed considerably harder to
make up for the lack of booster assistance. •
Func ... ion=ng of Anti-Lock Brake System (ABS)
ABS prevents the wheels from locking up under braking.
The ABS contributes effectively to vehicle control since it prevents
the wheels from locking when the brakes are applied. This means
that the vehicle remains steerable and is less likely to skid.
With ABS you do not need to pump the brake. Just hold the brake
pedal down.
However, do not expect that the ABS shortens braking distance
under
all circumstances . When driving on gravel or on newly fallen
snow on top of icy surfaces, braking distance may be even longer,
therefore, under these circumstances, it is especially important that
you drive slowly and with great care. .,_

The exclusive use of unleaded fuel is critically important for the life
of the catalytic converter and proper functioning of the engine.
& WARNING
• Do not park or operate the vehicle in areas where the hot
exhaust system may come in contact with dry grass, brush, fuel
spill or other material which can cause a fire.
• Do not apply additional undercoating or rustproofing on or
near the exhaust manifold, exhaust pipes, catalytic converter or
heat shields . During driving, the substance used for undercoating
could overheat and cause a fire.
0 Note
• Be aware that just one tank filling with leaded fuel will already
seriously degrade the performance of the catalytic converter.
• Do not exceed the correct engine oil level~
page 230.
• Do not drive until the fuel tank becomes completely empty. The
engine could misfire. Unburned fuel could also get into the exhaust
system and this could cause the catalytic converter to overheat.
• Do not turn off the ignition while the vehicle is moving.
• Do not continue to operate your vehicle under these conditions,
as otherwise fuel can reach the catalytic converter. This could result
in overheating of the converter, requiring its replacement.
• To assure efficient operation of the Emission Control System :
- Have your vehicle maintained properly and in accordance with
the service recommendations in your Warranty
& Maintenance
booklet.
- Lack of proper maintenance as well as improper use of the
vehicle will impair the function of the emission control system
and could lead to damage.
Controls and equip­ ment Safety first Vehicle operation
Driving and environment
<£' For the sake of the environment
Even
when the Emission Control System is operating properly, the
exhaust gas can have a sulfur -like exhaust gas smell under some
operating states . This depends on the sulfur content of the fuel
being used . Using a different brand of fuel may help, or filling the
tank with lead-free super grade gasoline. •
Applies to veh ic les : with diesel particulate filter
Diesel particu ate filter
The diesel particulate filter filters nearly all of the soot particles out
of the exhaust. The filter cleans itself automatically under normal
driving conditions. If the filter cannot clean itself (for example,
because you are only driving short distances), the filter becomes
clogged with soot and the symbol for the diesel particulate filter
illuminates ~
page 32.
& WARNING
• Do not park your vehicle over flammable materials such as
grass or leaves because the high temperature of the diesel partic­
ulate filter could start a fire.
• Do not apply an underbody protectant in the exhaust system
area or a fire could start.
[ i] Tips
• When the diesel particulate filter becomes saturated, the engine
speed increases to approximately 1,500 rpm while the vehicle is in
motion to initiate the cleaning of the diesel particulate filter auto­
matically without the warning lamp lighting up. If the warning lamp
still appears, you should drive to a qualified workshop. •
Vehicle care Do-it-yourself service Technical data

long waits on red. Turning the engine off for just 30 -40 seconds
saves more f ue l than i s bu rned star ting the engine again.
It takes a long time for the engine to warm up fully when it is
running at idle. However , wear and noxious em issions are especial ly
h ig h w hen the eng ine is warming up. So y ou should dr ive away as
soon as you start the engine and avoid running at high RPMs whi le
the eng ine is still warming up.
0 Note
Do not leave en gine idling unattended after starting. If warn ing
lights should come on to indicate improper operation, they would
go unheeded . Extended idling also produces heat, wh ich cou ld
result in overheating or other damage to the vehicle or other
property .
Regular maintenance
A badly tuned engine unnecessarily wastes a lot of fuel.
- Have your vehicle serviced at regu lar intervals.
By having your vehicle regu lar ly serviced by an authorized Audi
dea ler he lps to ensure that it runs properly and econo mically . The
condition of your vehicle not only affects its safety and abi lity to
hold i ts va lue, it a lso affects fuel consumpt ion .
Che ck yo ur oil ea ch t ime you fill your t ank.
T he amount of oil used is related to engine load and speed.
It is nor mal for the oil consumption of a new engine to reach its
lowest va lue after a certain mi leage has been driven.
You must drive your vehicle about 3,000 mi les (5,000 kilometers)
before you can proper ly assess oil consumption .
T his also applies to fuel consumption and engine output.
Controls and equip­ ment Safety first Vehicle operation
Dri
ving and environm ent
0 Note
• Have your vehicle maintained properly and in accordance with
the service recommendations in your Warranty
& Maintenance
booklet. Lack of proper maintenance as we ll as improper use of the
vehic le wi ll impair the function of the emission control system and
cou ld lead to damage .
• Do not alter or remove any component of the Emission Control
System unless approved by the manufacturer .
• Do not alter or remove any device, such as heat shields,
sw itches, ignition wires, valves, which are designed to protect your
vehic le's Emission Control System and other important vehicle
components. •
Fewer short trips
Fuel consump tion will always be relatively hi gh on shor t
trips.
- Try to avo id driving short dista nces wi th a cold en gine.
The engine and cata lytic c onverter have to reach their optima l oper ­
ating temperature to reduce fuel consumption and noxious emis ­
sions effective ly .
• Just after starting, a cold engine in a mid-size car burns the fuel
at a poor rate of 6 -8 miles per gallon (30 -40 11100km). Half a mi le
down the road, the mileage improves to 12 MPG (20 1/100 km). It wi ll
take the engine no less than
two and a half miles (4 km) of driving to
warm up to its proper operat ing temperature and operate at a n
economic mileage . This exp lains why taking the car for short trips is
a ra ther waste ful convenience .
• The outs ide temperat ure is also critical in this regard. Your car
consumes more fuel in the winter than in the summer .•
Vehicle care Do-it-yourself service Technical data

___ T_ r _a_ il_e _r_ t_ o_ vv_ in__... g,_ __________________________________________________ _
Weig ht dis tributi on
Towing a loaded trailer with an empty car resu lts in a high ly
unstable distribution of weight . If this cannot be avoided drive at
very low speeds on ly to avoid the risk of losing steering control.
A "ba lanced" rig is easier to operate and control. This means that
the tow vehicle should be loaded to the extent possible and permis ­
sib le while keeping the trai ler as light as possib le under the circum ­
stances. Whenever possible, transfer some cargo to the luggage
compartment of the tow vehicle while observing tongue load requirements and vehicle loading considerations .
Speed
The higher the speed, the more difficult it becomes for the driver to
control the rig . Do not drive at the maximum permissible speed.
Reduce your speed even more under unfavorable load, weather or
wind conditions -particularly when going downhill.
Reduce vehicle speed
imm ed ia tely if the trailer shows the sl ightest
sign of swaying. Do not try to s top the s wayi ng by a ccelerating .
Observe speed limits . In some areas speeds for vehicles towing
trai lers are lower than for regular vehicles.
Always app ly brakes early. When driving downhill, shift into lower
gear to use the engine braking effect to slow down the vehicle. Use
of the brakes alone can cause them to overheat and fail.
C oo la nt tempe ra tu re
The coolant temperature gauge ~ page 9 must be observed care ­
ful ly. If the needle moves close to the upper end of the scale, reduce
speed immediately and/or switch off the air condit ioner.
If the coolant temperature warning light in the instrument cluster
starts flashing -~-, pull off the road, stop and let the engine
idle for
about two minutes to prevent heat build -up .
& WARNING
An yone not p rope rly res train ed in a mo ving vehi cle is a t a mu ch
gre ater risk in a n accident. Neve r let an yone ride in your car who
is not p rop erly we ari ng th e res tra int s pro vide d b y Aud i.
c
Trailer towing tips
Important to know
Your vehicle handles different ly when towing a trailer because of
the additional weight and weight distribution . Safety, performance
and economy w ill great ly depend on how carefu lly you load your
trailer and operate your rig.
Before you actually tow you r trailer, practice turn ing, stopping and
backing up in an area away from traffic. Keep practicing unti l you
have complete ly become familiar with the way your vehicle -trailer
combination behaves and responds .
Backing up is difficult and requires practice. Backing up with a
trailer genera lly requires steering ac tion opposite of that when
backing up your vehicle without a trailer .
Maintain a greater distance between your vehicle and the one in
front of you. You will need more room to stop.
T o compensate for the trailer, you wi ll need a larger than normal
turning radius .
When passing, remember that you cannot accelerate as fast as you n ormal ly wou ld because of the added load . Make su re you have
enough room to pass. After passing, al low plenty of room for your
trailer before changing lanes again .
Avoid jerky starts, sharp turns o r rapid lane changes.

___ C _l_e _a _ n_ in_g ~_ a_n _ d ___ p ___ r_ o _t _e _c_ t_ i_o _ n _____________________________________________ _
Cleaning and protection
General information
Regular care p rese rves vehicle value .
Any automobile is exposed to industrial fumes, corrosive road salt ,
muddy dog feet, e tc. A wel l cared fo r Audi can look l ike new many
years after purchase . Regu lar and correct care will contribute to
maintaining the beauty and va lue of your Audi .
Furthermo re , g ood care ma y be a conditi on for sub sta ntiating a
warr anty cla im should corro sion damage or paint defect s occur .
Your authorized Audi dealer has a var iety of dedi cat ed vehicle -care
product s
and can advise which ones to use for cleaning the exterior
and interio r of your vehicle.
Whether you use products recommended by Audi or other commer ­
cially availab le cleaning agen ts, please make su re you apply them
correctly .
& WARNING
• Cleaning agents m ay be poi sonou s. Keep them out of the re ach
of childr en.
• Heed all cau tion label s.
• Alway s read direction s on the container before u sing any
produ ct. Follo w the dire ction s carefull y.
• Most chemi cal cle aner s are concentr ated and h ave to be
d iluted .
• Use spot remo ving fl uid s onl y
in well ventila ted are as.
• Do not use gasoline , kero sene , diesel fuel , nail poli sh remover
or other vol atil e fluid s. They may be to xic , fl ammab le or h azardou s
in other wa ys. Do not wa sh , wax or dry the vehicle w ith the igni ­
tion on or the engine ru nning .
& WARNING (continu ed )
• Do not clean the unders ide s of cha ssi s, fenders , wheel cover s,
et c. without pr ote cting y our hands and arm s. You may cut your self
on sh arp-edged metal part s.
• Moisture and i ce on brakes may impair br aking eff icien cy
~ page 191 , "General information ". Test the brake s carefully each
time you wash the vehicle .
'£> For the sake of the environment
Select only environmenta lly friend ly c leaning products. Leftover
clean ing products should not disposed of in the household waste .•
Care of exterior
Washing
F requent washing protects the vehicle.
The best protection against environmental influences is frequent
washing a nd waxing.
How often this is required depends on :
• How much the vehicle is used
• Where the vehicle is parked (garage, in the open under trees ,
etc.)
• The seasonal and weather conditions
• Environmenta l influences
The longer bird droppings, insects, tree resin, road and industrial
gri me, tar, soot, road salt and other materials remain on the vehicle
body , the more lasting their destructive effects will be. .,_

____________________________________________ _:C ::,: l~ e :,: a~ n:....:..:..: in~ g~ a~n .:.:d:!...! p~ r ~o~ te~ c~t ~io ~ n'....__lfll
•
T he best way to remove snow from windows and mirrors is to use a
brush . Use a non -abrasive
pla stic ice scraper -better still, a spray
deicer -to remove
ice from w indows and mirrors .
The windows must not be cleaned with insect remover or wax since
these can inter fere with the function of the w inds hie ld w iper blades
(chatter).
Oil, grease o r sil icone residue can be removed with
glass cleaner or
s ilicone remover . However, wax residue requires the use of a
spec ially fo rmulated so lvent . Please contac t your authorized Audi
dea ler for advice on safe products for wax removal.
Windows should also be c leaned on the inside at regular interva ls .
Never dry windows with the same chamois that you use to dry
painted surfaces . Wax residue on the chamois can impair vision
t hrough the windows .
& WARNING
• The windshield mu st not be treated with water -repellent mate ­
rials. T hey c an incre ase gl are under poor v isibility conditions such
a s wetne ss, darkne ss, or when the sun i s low on the hori zon. In
addition , they can cause the wind shield wipers to chatter .
• Alway s read and heed all WARNINGS and other information
~ page 204.
0 Note
• Never use warm or hot water to remove snow and ice from
windows a nd mirrors . This cou ld cause the glass to crack.
• T o prevent damage to the wires of the rear defogger, do not p lace
any adhesive stickers on the inside of the rear window over the
wires .
• T o he lp prevent dirt from scratching the window, always scrape
in a forward direction -pushing the scraper away from you -never
back and forth. •
Weatherstrips
Complete car car e includes the we atherst rip s as well .
App ly a suitable rubbe r con ditioner to the weatherstr ips
f ro m time to time.
To be able sea l properly, the weatherstrips around the hood, doors,
rear lid, etc . must remain pliabl e. Spray the weatherstrips with sili­
co ne or coat them w ith ta lcum powder or glycer ine to retain the
f lexibility of the rubber and to protect them against freezing in the
winte r.
& WARNING
Always read and heed all WARNINGS and other information
~ page 204.
[ i ] Tip s
Keep si licone sprays off the windshield to avoid wiper smear in
ra in .•
Ap plies to veh icles : with s tee l w hee ls (e .g . if ref itt e d w ith w inter tires )
Steel wheels
The wheels also h ave to be cleaned.
- Alw ays in clu de the hu b caps and whee l rims when
washing yo ur vehi cle to remove road dir t, sal t sprays an d
b rake dust.
If necessary, use a commercial whee l cleaner to remove accumu ­
lated brake dust.
The wheel rims are eas ier to keep clean if they are reg ula rly coa ted
with l iquid wax . ..
Vehicle care I t •

-Cleaning and prot
ection
-~--------------
In the case of genera l soiling of the upho lstery and cover material,
we recommend hiring a s pecialis t tha t has the equ ip m ent to c lean
the seat covers and other fabric surfaces by shampooing and spray
e xtraction .
& WARNING
Always read and heed all WARNINGS and the information
~ page 204 .
[ i ] Tip s
Open Ve lcro fasteners on your clothing can damage the seat cover.
Please make sure that Velc ro fas tene rs a re c losed. •
Plastic parts and instrument panel
- Always use a clean c lo th moiste ned in clear wa ter.
A lways use a c lean cloth moistened in clear water to clean these
areas. For persistent d irt use a n Aud i approved
solvent -free plastic
cleaner/protectant .
& WARNING
Solvents can change the properties of some plastics and make it
harder for the airbag to deploy.
• Never clean the instrument panel or the surface of A irbag
modules with cleaning produ cts that contain solvents.
• Product s containing solvents will make the surface of this part
porous .
• Serious injuries can re sult if plastic parts come loose when the
airbag is deployed .
• Always read and heed all WARNINGS and the information
~ page 204.
0 Note
Cleaning agents co ntaini ng so lvents wil l attack t he ma ter ial and can
change the way it behaves .•
Ap plies t o ve hicles : w ith na tural leat her
Natural leather
Aud i makes great eff orts to maintain the pro per ties,
n atu ra l look and feel of in ter ior leather.
General
We offer many different types of leather on our vehicles. Most are different types o f nappa leather, which has a smooth surface and
comes in various co lors.
The intens ity of the color de termi nes the vis ual c h aracteris tics and
appearance. If the surface of the leather has a typica l natural look ,
t hen t he leather is a nap pa lea ther tha t has been left in a re lati ve ly
natural condition. This leather offers particu lar ly good comfor t and
breathes well. Fine veins, closed grains, insect bites, skin folds, and
subt le variations in color remain visib le. These character istics
demonstrate that the material is natura l.
N at ura l n ap pa leather is not covere d by a col or fin is h. It is the refor e
more sensitive to soiling and wear, which is something you need to
co nside r if chi ld ren, a nim als o r othe r factors m ight prove to be
particularly hard on the leather.
By contrast, leather types that are covered by a colored finish layer
ar e mo re du rable. T his has a positive ef fect on the leather's resis ­
tance to wear and soiling in daily use. On the other hand, the typical
cha ract erist ics of natura l leather are barely or n ot appa ren t.
However, th is does not mean that the leather itself is of inferior
quali ty.
Care and handling
Becaus e of th e exclusive nat ure of the ty pes o f lea ther tha t Audi
uses and their un ique properties (such as sens itivity to oi ls, grease, ..,_

•
labeled ask the station operator what fuel is being dispensed before
filling up your vehic le .
Service stations offering diesel fuel are generally located on truck
routes or major highways. Directories of diesel fuel stations are
usually available at diese l fuel stations.
Some states in the USA require permits to purchase diesel fuel.
Check with your State Motor Vehicle Department.
Diesel fuel may not be available outside the USA and Canada . Be
su re to check before traveling to other countries .
Winte r ope ra ti on
At temperatures be low 20° F (- 7° Cl, Diesel fuel No. 2 loses its fluidity
due to wax separation, which may c log the fuel filter or tank filter
and keep the engine from running.
To he lp the filter from being clogged by wax, the fue l filter in your
vehic le is automatically preheated. Preheating the fuel fi lter makes
operation of your vehicle poss ible with Diese l fue l No. 2 down to -
10° F (- 24° Cl.
If you expect tempe ratures below 5° F ( -15° C) ask your fuel dealer
whether their Diesel fuel No. 2 is sufficiently winterized for the prevai ling and expected temperatures .
If not winterized or insufficiently winterized diesel fuel has already
thickened to the extent that the engine will not start, warm the
vehicle up by leaving it in a heated garage.
It is normal that the engine noise level (dieseling) is louder during
the warm -up per iod in winter. It is also normal when whitish -blue
smoke comes out of the tailpipe after starting and dur ing warm-up.
The amount of smoke depends on the outside temperature .
Do not let your diese l eng ine idle unnecessarily after a cold start.
Driving off slowly will shorten the warm -up period.
F ue l supply and fillin g you r fu el tank
& WARNING
• Never use "s tarting a ssis t f luid s." They m ay be pot entiall y
explo sive or c au se a " run-away " engine condition. Thi s cou ld
re sult in serious e ngin e da ma ge a nd pe rsonal injury.
• Never use fu el line anti -free ze offer ed f or ga soline engine s.
0 Note
• Your diesel engine has been speci fically designed to operate
only on Ultra Low Sulfur Diese l fuel. Therefore, never use home
heating oi l or regular gaso line . The properties of these fuels may
cause serious damage to the fuel injection system and to the
engine . Using these fuels can cause expensive engine repairs and
wi ll also adversely affect your New Vehic le Limited Warranty.
• I f diese l fue l should get on any rubber hose, it must be wiped off
immediately . Then wash the contaminated hose portion with soap
and warm water. Do not allow diesel fuel to remain on connecting
hoses. They may develop leaks and cause serious damage. •
Fuel tank
Fuel filler neck
The fuel filler neck is located o n the right rear s ide panel behind the
fuel filler f lap.
I f the powe r locking system should fa il, you can still open the flap
manually - for detailed instructions see:::::,
page 222.
You can find the fuel tank capacity of your vehicle in Techni cal Data
:::::, page 296 .
The label on the inside of the fuel filler flap tells you the correct fuel
for your vehicle. F or more informa tion about fue l specifications, see
=:> page 217. _,,
Vehicle care I t •