wheel AUDI S3 2011 Owner's Manual

_______________________________________________ A_ ir_ b_ a_,,,g '--- s.:a.y _s _t_ e _ m ___ _
lower parts of the body . Front a irbags s upplement the t hree-poi nt
sa fety belts o nly in some fro ntal collis ions in which the vehicle decel­
eration is high enough to dep loy the a irbags .
Front airbags will not deploy:
• if the ignition is switched off when a crash occurs,
• in s ide collisions ,
• in rea r-end collisions,
• in rollovers,
• when the crash decelerat io n me asured by the a irbag system is less
than the min imum threshold needed for a irbag deployment as reg is­
tered by the e lectron ic con trol un it.
The front passenger airbag also will not deploy:
• when the fron t passe nger seat i s not oc cupied,
• when the weight on the front passenger seat as sensed by the
Advanced Ai rbag System in dicates that the front airbag o n the
passenger side has to be turned off by the e lectronic control unit (the
PASSENGER AIR BAG OFF li ght comes on and stays on).
& WARNING
Sitting in the wrong position can increase the ri sk of ser iou s injury
in crashes.
• To redu ce the risk of injury when the airbags inflate, the driver
and pas sengers mu st always sit in an upright position , mu st not
lean against or place any part of th eir body too close to the area
where the airbags are lo cated.
• Occupants who are unbelted, out of position or too close to the
airbag can be seriou sly injured by an airbag a s it unfolds with
great force in th e blink of an eye =>
page 147 .
Controls and equip­ ment Safety first Vehicle operation
& WARNING
A child in a rearward-facing child
safety se at installed on the front
pa sseng er seat will be seriously injured and can be killed if the
front airbag inflat es - ev en with an Ad van ced Airbag System .
• The inflating airbag will hit the child safety seat or infant
c arrier with great force and will smash the child safety s eat and
c hild against the backre st, center armre st, d oor or roof .
• Always install rear -facing child safet y seats on the rear seat.
• If you must install a rearward facing child safety seat on the
front passenger se at because of e xceptional circumstances and
the PASSENGER AIR BAG OFF light do es not come on and stay on ,
immediately install the rear -facing child s afety seat in a rear
s eating po sition and h ave the airbag system inspe cted by your
authoriz ed Audi d ealer.
& WARNING
Object s between you and the airbag will increase th e risk of inju ry
in a cra sh by int erfering with the way the airb ag unfold s or by
being pushed into you as the airbag inflates.
• Never hold things in your hand s or on your lap when the vehicle
i s in use.
• Never tran sport items on o r in the are a of the fr ont pa ssenger
seat. Obje ct s c ould move into the area of the front ai rbag s during
braking or other sudden maneu ver s and become dang erous
projectiles that can c au se se rious per sonal injury if the ai rb ags
infl ate.
• Never pla ce o r atta ch acce ssorie s or other objects (such as cup
holder s, telephone brac ket s, large, hea vy or bulky objects ) on th e
doors , ov er or near the are a marked "AIRBAG" on the stee ring
wheel, in strum ent panel , se at ba ckre sts or between th ose ar ea s
and yourself . These objects could cause injur y in a crash , especially
when the airbags infl ate .
9"'
Vehicle care Do-it-yourself service Technical data

_______________________________________________ A_ ir_ b_ a_,,,g '--- s.:.y _s _t_ e _ m ___ _
& WARNING (co ntinued )
seating position and have the airbag system inspected by your
authorized Audi dealer.
• A tight tether o r other strap on a rearward -facing child
restraint attached to the front pa ssenger seat can put too much
pressure on the weight -sensing mat in the seat and register more
weight than i s actually on the seat . The heavier weight regi stered
can make the system work as though an adult were on the seat
and deploy the Advan ced Airbag when it mu st be suppre ssed
causing serious or even fatal injury to the child .
• If , in exceptional circumstanc es, you must install a forward­
facing child restraint on the front passenger seat, always move
the seat into its rearmost po sition in the seat' s fore and aft adjust­
ment range, as far away from the airbag as possible . The backrest
must be adjusted to an upright position. Make sure that the PASSENGER AIR BAG OFF light comes on and stays on all the time
whenever the ignition is switched on.
& WARNING
• If the PASSENGER AIR BAG OFF light doe s not go out when an
adult is sitting on the front passenger seat after taking the steps
described above, make sure the adult is properly seated and
restrained at one of the rear seating positions.
• Have the airbag system inspected by your authorized Audi
dealer before transporting anyone on the front passenger seat .
[ i ] Tips
If the we ight-sensing mat in the front passenger seat detects an
em pty seat , the front airbag on the passenge r side will be t urne d off,
and the PASSENGER AIR BAG OFF light will stay on .•
Controls and equip­ ment Safety first Vehicle operation
Repair, care and disposal of the airbags
Parts of the airbag system are
insta lled at many different places on
your Audi . Ins tall ing, remov ing, serv icing o r rep airi ng a pa rt in an
area of the vehicle ca n damage a part of a n airbag system and prevent
t ha t sys tem from working prope rly in a coll is io n.
Th ere are some importa nt things you have to know to ma ke sure t hat
the effectiveness of the system will not be impai red and that
dis ca rded compo nents do not cause injury or po llute t he e nvir on­
ment .
& WARNING
Improper care , serv icing and repair procedures can increase the
risk of personal injury and death by preventing an airbag from
deploying when needed or deploying an airbag unexpectedly:
• Never cover, obstruct, or change the steering wheel horn pad or
airbag cover or the instrument panel or modify them in any way .
• Never attach any objects such as cup holders or telephone
mountings to the surfaces covering the airbag units.
• For cleaning the horn pad or instrument panel, use only a soft ,
dry cloth or one moistened with plain water . Solvent s or cleaners
could damage the airbag cover or change the stiffness or strength
of the material so that the airbag cannot deploy and protect prop ­
erly.
• Never repair, adjust, or change any part s of the airbag system .
• All work on the steering wheel, instrument panel , front seats
or electrical sy stem (including the installation of audio equip­
ment, cellular telephones and CB radios, etc. ) must be performed
by a qualified technician who has the training and special equip­ ment necessary .
• For any work on the airbag system, we strongly recommend
that you see your authorized Audi dealer or qualified workshop.
• Never modify the front bumper or parts of the vehicle body . ..,_
Vehicle care Do-it-yourself service Technical data

-Child Safety _____ ____;_..:::.:!.----------------------------
& WA RNING (conti nued)
• Always install rear-facing child safet y seat s on the rear seat.
• If you must install a rearward facing child safety seat on the
front passenger seat in exceptional circumstances and the
PASSENGER AIR BAG OFF light do es not come on and stay on,
immediately in stall the rear-facing child safety seat in a rea r
seating position and have the airbag system inspected immedi­
ately by your authorized Audi dealer.
& WARNING
If , in exceptional circumstances , you must in stall a forward-facing
child restraint on the front passenger' s seat:
• Always make sure the forward-facing seat has been designed
and certified by its manufacturer for use on a front seat with a
pa ssenger front and side airbag.
• Always follow the manufacturer 's instructions p rovided with
the child safety seat or carrier.
• Always move the passenger seat into its rearmost position in
the seat's fore and aft adjustment range, as far away from the
airbag as possible before install ing the child restra int . The back­
re st must be adju sted to an upright position .
• Always make sure that the PASSENGER AIR BAG OFF light
c omes on and stays on all the time whenever the ignition i s
switched on .•
Advanced front airbag system and children
Your vehicle is equipped with an "Advanced Airbag System" in compli­
ance wi th Uni ted St ates Federa l Mo to r Vehicle Safety St andar d
(FMVSS) 208 as applicable at the time your veh icle was manufac­
tu red . The Advanced A
irbag system in yo ur vehicle has been certif ied to
mee t the "low -r is k" requiremen ts fo r 3-and 6-ye ar old ch ildre n on
t he passenger side and small adults on the dr iver side . The low risk
dep loyment criteria are inten ded to reduce the risk of injury through
interaction with the a irbag t hat can occur, for example, by being too
close to the stee ring wheel an d instr ument panel when the airbag
inflates. In addi tion, the sy stem has been certified to comp ly with t he
"suppression" requirements of the Safety Standa rd, to t urn off the
fron t air bag for infan ts u p to 1 2 months who a re res tra ined on the
front passenger seat in child restrai nts that are listed in the Stan­
d ar d.
Even thoug h your vehicle is equipped with an Advanced Airbag
system , a ll ch ildren, especially those 12 years and yo unger, should
always r ide in t he back seat p roperly restrained for t heir ag e and si ze .
Th e ai rbag on the passenge r si de makes the front seat a potentia lly
dange rous p lace for a child to r ide. Th e front seat is not th e safest
place fo r a child in a forward- facing c hild safety seat. It can be a very
d an ge rous p lace for a n infan t or a large r chil d i n a rea rwa rd-facing
seat. •
Advanced Airbags and the weight-sensing
mat in the front seat
Th e Advanced A irbag System i n your ve hicle de tects t he p resence o f
an infa nt o r ch ild in a child rest rai nt on the fro nt passenger sea t using
the we ight-sens ing mat in the seat cushion and the senso r be low the
saf ety belt la tch o n th e front passenge r seat tha t measur es t he
tension on the safety belt.
Th e weigh t-sens ing ma t me asures tot al we ight of the child and the
child safety seat and a child blanket on the fro nt passe nger seat . The
we ight on the fro nt passenger se at is re late d t o the desi gn of the
child res traint and i ts "footpri nt", the size and shape of t he bottom
of the ch ild restraint as it sits o n the seat . The weight of a child
restrain t an d its "foo tpr int" vary for differe nt kinds of child res tra ints .,_

Intelligent technology
'-----------------------------------------------
Intelligent technology
Notice about data recorded by
vehicle control modules
Your vehicle is not equipped with an Event Data Recorder (EDR),
installed by some manufacturers for the express purpose of
capturing data for retrieva l after an accident or crash event. ED R's are
sometimes called "crash recorders".
Some state laws restrict the retrieval or downloading of data stored
by ED R's that were installed in a vehicle for the express purpose of
retrieving data after an accident or crash event without the owner's
consent.
Although your vehicle is not equipped with an EDR, it is equipped w ith
a number of electronic control modu les for various vehicle systems
such as, for example, engine function, emission control, as well as for
the airbags and safety belts.
T hese electronic contro l modules also record vehicle-re lated data
during normal vehicle operation for diagnostic and repair purposes .
Th e recording capacity of the e lectronic control modu les is limited to
data (no sound is recorded) and only a sma ll amount of data is actu­
ally recorded over a very limited period of time and stored when a
system fault or other condition is sensed by a control unit. Some of
the data then stored may relate to vehicle speed, direction, braking
as well as restraint system use and performance in the event of a
crash or other condition. Stored data can only be read and down­
loaded with special equipment.
Electronic Stabilization Program
(ESP)
General
The Electronic Stability Program increases driving
stability .
With ESP, contro l over the vehicle is increased in situations when the
vehicle is close to the limits of grip, such as dur ing accelerat ion and in
curves. ESP reduces the risk of sk idding and improves vehicle stability
unde r all road conditions.
It operates at all speeds.
The Anti-Lock Brake System (ABS), Electronic Differential Lock (EDS) and Anti-Slip Regulation System (ASR) are integrated in the Elec­
tronic Stability Program .
How ESP works
The ESP control unit processes the following data from high-sensitive
sensors: the rotationa l speed of the vehicle about its vertical axis,
fore-and -aft and lateral acceleration forces, brake pressure and
steering angle .
Us ing stee ring ang le and vehicle speed, the direction the driver
wishes to travel is determined and continuously compared with
actual vehicle behavior. If the two do not match, for example when
the vehicle beg ins to skid, ESP brakes the appropriate whee l auto­
matically.
The vehicle is stabilized aga in by the forces act ing on the whee l
during braking. With an oversteering veh icle (tendency for the rear
end to skid out of the curve), the brake app lication is mainly at the
front wheel on the outside of the curve, with an understeering vehicle
(tendency to run wide in the curve) at the rear wheel on the insid e of
the curve or additionally at the other wheels as needed. This brake
application is accompanied by noises. _,

_________________________________________ I_ n_ t_ e_ ll_,igent technology ,__E~-
ESP works in co njunction w ith ABS~ page 192 . If there is malfunc­
t ion in the ABS, ESP is also inoperat ive.
& WARNING
• The limit s of phy sics cannot be su spended by ESP. Even in vehi­
cles with ESP, you should always adapt your driving to road and
traffic conditions. Thi s is particularly true on a slippery and wet
road. Do not be tempted by the increased safety provided to take
ri sk s - danger of an a ccident!
• Please note that when ESP / ASR is deact ivated , the drive
wheel s can spin on icy and slippery roads and the vehicle can break
away -danger of skidd ing! •
Switching on and off
Fig. 155 C ente r
con sole w ith ESP
s wit ch
Th e ESP i s automa tically activ ated w hen the eng ine is st arted, and i t
performs a self-test. As soon as the test is comp leted, the system is
in normal operat ing mode .
Deactivating
ES P s hould no rm ally be activate d at all times beca u se this ens ures
optimum veh icle stability. Only in some cases it does make sense to
de activ at e t he Elect roni c Stabili ty Pr ogr am ( ES P) by p ress ing the
button~ fig. 155. Deact ivat io n i s indicated by the ESP lamp
J! in the
Controls and equip­
ment Safety first
Vehicle operation
instrument cluster flashes . The message ESP OFF appears in the
ins trument cl uste r. Ant i-Slip Regula tion is comp le tely deact iv a te d
and the stab ilizat io n effects from the ESP system are lim ited. This
ma kes a more agile and spo rty driving sty le possible, but the full
extent o f th e stabilization function is not available .
Activating
~~~= Press the [ESP OFF ) button again~ fig. 155 . The ind icator lig ht
goes out . The message
ESP ON appears br iefly in the ins trumen t
cluster disp lay .
& WARNING
You should only switch the ESP off if your driv ing ability and the
traffic situation allow. Please note that when ESP /ASR i s dea cti­
vated, the drive wheels can spin on icy and slippery roads and th e
vehicle can break away -danger of skidding!
[ i ] Tips
If Audi magnetic r ide* is ma lf u nct io ning, the ESP may not sw itch off
or it may switch off automatically . •
Electronic differential lock (EDL}
The ele ctr onic dif ferential lock mo nit ors the rot ational
s p eed of the d rive wheels .
General notes
The elec tron ic differe ntia l lock ( EDL) helps the ca r to sta rt movin g,
acce le ra te and climb a gradient on surfaces provid ing poor or almost
no grip. Without E DL, this would be difficult, if not impossible.
How the system works
Th e E DL operates au tomatically . It mo nitors the rotational s peed of
t he drive wheels on an axle with the he lp of the ABS sensors
~ page 19 2. If a noticeable difference in rotational speed between ..
Vehicle care Do-it-yourself service Technical data

Intelligent technologyL ______________________________________ _
the drive wheels on one axle is detected (e.g . on slippery ground on
one side),
the spinning wheel is braked, thereby transferring power to
the other drive wheel or wheels (all -wheel drive) . This is done up to a
speed of about 60 mph (100 km/h). Noises from the brake system
signal that wheel sp in is being controlled .
Driving off
When driving off, always be sure to keep road conditions in mind as
you accelerate . If one drive wheel spins because it is on a surface with
less grip, gradually increase the pressure on the accelerator pedal
until the car starts to move. The wheel less ab le to transfer power
spms .
Overheating of brakes
To prevent the disc brake of the braked wheel from overheating if
subjected to excessive loads, the EDL cuts out temporarily. The
vehicle remains operat ional and behaves in the same way as a vehicle
without EDL .
As soon as the brake has cooled down, EDL switch es on again auto­
matically.
Electronic limited slip differential*
In vehicles w ith front wheel drive*, an electronic lim ited slip differen­
tial engages when driving on curves. The brakes are applied spec ifi­
cally to the front wheel that is on the inside of the curve. This mini­
m izes sliding on the front wheels and enables precise and neutral
driving through curves. The electronic limited slip differential does
not engage when d riving in wet conditions or snow.
& WARNING
• When accelerating on slippery surfaces, such as on ice or snow,
always be careful when depressing the accelerator pedal. Even
with the EDL and the ele ctronic limited slip differential working,
the drive wheels can spin and reduce your ability to control your
ca r. -Risk of crash!
& WARNING (continued)
• The increased safety afforded by EDL and the electronic limited
slip differential does not mean that you can take safety risks .
Always adapt your driving style to the road conditions and traffic
situation.
[I) Tips
If a fau lt occurs in the ABS, the EDL is also not f unct ioni ng. This is
indicated by the ABS warning light=>
page 16.
Anti-Slip Regulation System (ASR)
The Anti-Slip Regulation System prevents the driven
wheels from spinning when the car is accelerating.
General notes
The Anti-Sl ip Regu lation System (ASR) is integrated in the electronic
stabili zation program (ESP) . When the vehicle starts up and acceler­
ates, the wheels are prevented from sp inning by adjust ing the engine
power to match the amount of grip available from the road surface.
How the system works
ASR performs automatica lly, i.e. without the driver's intervention.
With the aid of the ABS sensors=>
page 192, ASR monitors the speed
of the driven wheels. If the wheels start to spin, the engine torque is
reduced automatically until the tires find enough grip to lock onto
the road surface. The system is active across the entire speed range.
The ASR works in conjunction with the ABS. If a malfunction shou ld
occur in the ABS, the ASR w ill also be out of action .
[I) Tips
To ensure that the ASR works properly, all four wheels must be fitted
with identical tires. Any differences in rolling radius of the tires can .,

_________________________________________ I_ n_ t_ e_ ll_,igent technology ,__E~-
cause the system to red uce eng ine power when t his is not desired .
See also =>
page 2 57 , "N ew tir es and rep lacing tires and whee ls". •
Braking
General Information
What af fect s braki ng effici ency ?
Operating condit ions and driv ing habits
Th e br akes on today's autom obil es are s till subjec t to we ar,
depend ing large ly on operating conditions and driving habits=>& .
O n veh icles t hat are ei ther driven mos tly in sto p-an d-go ci ty traff ic or
are driven ha rd, the bra ke pads s hould be checked by your author ized
Aud i dealer mo re o ften t han specif ied in the
Warranty & Mainte­
nance booklet .
Failure to have your brake pads ins pected can resu lt
in re duced brake pe rformance.
O n steep slopes, you shou ld use the brak ing effect of th e engine . This
way, yo u prevent unnecessary wea r on the brake system. If yo u must
u se your b ra kes, do n ot ho ld the bra kes down conti nuou sly. P u m p the
brakes at intervals .
N oises may occur when brakin g dependin g on s peed, braki ng fo rce
and outs ide cond itions s uch as temperatu re and hum id ity.
Moisture or road salt
If you are driving fas ter than 50 mp h (8 0 km/h) and th e w indshield
w ipers are on , the b ra ke pads w ill briefly touch t he br ake discs in
reg ula r intervals so as to improve react io n ti me when brak ing on wet
s u rfaces. Yo u, the drive r, will not not ice anything .
Under cert ain con ditions , for ex am ple , w hen driving throug h w ater or
very heavy rain, or even after was hing your veh icle, the bra king effect
c an be redu ced due to moi sture (or in fr eezin g condi tion s ice) on the
brake pads . A few cautious brake app lications sho uld dry off the
bra ke p ads or remove any ice coa ting s.
Controls and equip­
ment Safety first Vehicle operation
T
he effect iveness of the brakes can be reduced when the vehicle is
dr ive n o n a salt-c overe d road and t he brakes are not us ed. Likew ise,
you clea n off acc umulated salt coat ing from brake d iscs and pads
w ith a few cautio us app lications of the brake=>& .
Corrosion
There ma y be a te nd ency fo r dirt to b uild up o n the brak e pa ds and
co rrosion to form on the discs if the car is not dr iven regu la rly o r only
for short trip s wit h litt le u se of the bra kes.
If th e bra kes are not used freq uent ly, or if co rrosion has formed o n
th e discs, it is advisable to clean off the pads an d discs by brak ing
fi rmly a few times fro m a mode ra tely high speed =>& .
Faults in the brake system
If yo u should no tice a sudden increas e in brake pedal t ravel, then one
o f the two brake ci rcu its may have failed =>& .
Low brake fluid level
Malf u nctions can occu r in t he brake sys tem if the brake fluid level is
t oo low . T he bra ke fluid level is mo nitored e lectro nica lly .
Brake lining wear status
Brake lining wear may be checked by v isua l inspect ion of the condi­
t ion of the bra ke pa ds through the o penings in the wheel. If neces ­
sary , the whee l may be removed for th is inspect ion=>
page 27 2,
"Wheel c hange" .
& WARNING
• You should perform braking maneuvers for the purpose of
cleaning the brake system only if road conditions permit . Other
road users must not be put at risk -you may cause an accident!
• Before descending a steep grade, reduce speed and shift trans­
mission into a lower gear or lower driving range. Do not ride the
brakes or hold the pedal down too long or too often. This could
cause the brakes to get hot and diminish braking efficiency.
~
Vehicle care Do-it-yourself service Technical data

Intelligent technology
'-----------------------------------------------
& WA RNING (conti nu ed )
• Do not "ride the brakes " by re sting your foot on the pedal when
you do not intend to brake . Thi s may cause the brakes to overheat,
premature wear and increased stopping distance.
• Under certain climatic and operating condition s such as
pa ssing through water, dr iving in heavy rain or after washing the
vehicle, the effectiveness of the brake s can be reduced . In winter ,
ice can accumulate on the brake pads , linings , discs and drums .
Carefully apply brakes for a te st. Brakes will dry and ice coatings
will be cleaned off after a few careful brake applications.
• Driving for an extended period of time on salt-covered roads
without using your brakes can al so affect br aking efficiency. Clean
off accumulated salt coating from brake disc s and pads with a few
careful brake applic ations.
• If you damage the front spoiler , or if you in stall a different
spoile r, be sure the air flow to the front brakes is not obstructed.
Otherwi se th e brake system could overheat reducing the effective­
ness of the entire brake system.
• Failure of one brake circuit will impair the braking capability
resulting in an inc reased stopping distance. Avoid driving the
vehicle and have it towed to the nearest authorized Audi dealer or
qualified wo rkshop .
.J
Brake booster
T h e brake booste r adds ext ra braking p ower.
The brake booster works with vacuum pressure which is created on ly
w hen the eng ine is ru nnin g=>&.
& WARNING
• Never let the vehicle roll to a stop with the engine shut off.
• If the brake boo ster i s not working , for example when towing
your veh icle , or because the brake booster has somehow been
& W ARNING (continued )
damaged , the brake pedal must be p ressed considerably harder to
make up for the la ck of booster assi stan ce. •
Functioning of Anti-Lock Brake System
{ABS)
ABS prevents the wheels from l ockin g up under br aking.
Th e ABS contr ibutes effectively to vehicle co ntrol s ince it prevents t he
w heels from
locking when the brakes are applied . This means that the
veh icle rema ins steerable and is less likely to skid .
With ABS you do not need to pump the brake. Just hold the brake
pedal down .
However, do no t expect that the ABS shortens bra king d istance under
all circumstances . When dr iv ing on grave l or on newly falle n snow on
top of icy s urfaces, braking d istance may be even longer, therefo re,
under these circumstances, it is especially important that yo u drive
slowly and with g re at c are.
How the ABS system works
An au tomatic c hec k is made when a speed of about 4 mp h (6 km/ h) is
reached. When t his happens, a pump ing noise can be heard.
If an ind ivi dual wheel begi ns to rot ate too s low ly in relat ion to ve hicle
speed and tends to loc k, t he ABS automatically reduces brake pres­
s ur e to p revent t hat wheel from lo cking.
T hi s au tomatic adjustment p rocess w ill cause a
s light vibration of
the bra ke pedal and some noises to a lert you that vehicle speed must
be adapted to ex isting road and traffic co nditions .
& WARNING
Although the ABS is very effective, always remember that braking
capability is limited by tire traction. Always adjust your driving ...

Intelligent technologyz..__~~-____________________________ __.
& WA RNING (c on tinued )
speed acco rding to the road and traffic conditions. Do not let the
e xtra safety afforded by th e ABS tempt you into taking extra risk s.
The ABS cannot overcome the laws of physics .
[ i J Tips
• If ABS is not funct ioning properly, a warning light will come on .
See ~
page 16 .
• If a fault occurs in the ABS, the EDL is also not functioning. This is
ind ic at ed by t he A BS w arni ng light. •
Brake assistant
The broke assistant is designed to achieve the optimum
br oking effect.
Th e b rake ass istant he lps to inc rease t he effective brak ing powe r and
thus to ac hieve a shorter stopping distance.
If the driver presses the
bra ke ped al ve ry qu ickly, the b rake assistant au toma tically bo osts the
brak ing force to the max imum level, up to the point where the anti­
lo ck brak e function (ABS) in tervenes to stop the whee ls from l ocking.
You should then keep the brake pedal pressed unti l the vehicle has
bra ke d to t he require d spee d. T he bra ke ass istan t swi tches itse lf off
as soon as you re lease the b rake pedal.
Th e brake assistant will not be operative if there is a ma lfu nctio n in
t he A BS .
& WARNING
Please remember that the accident risk always increases if you
drive too fast , especially in corners or on a slippery road , or if you
follow th e vehicle ahead of you too closely. An increased accident
risk cannot be compensated even by the brake assistant, so always
maintain a safe speed .•
Controls and equip­ ment Safety first Vehicle operation
Electro-mechanical power assist
---
T
he elec tro-m echa nic al po wer as sist hel ps the dri ver
w he n steering .
The degree of power assist is electronically matched to vehicle speed.
Th e powe r steering system ass ists the dr iver so t hat he ca n stee r the
vehicle with reduced physical effort.
Power steering will not wor k if the engine is off. As a result, the
stee rin g wheel will b e ha rd to tu rn .
& WARNING
If the system deve lops a problem, you must seek qualified profes­
sional as sistance.
0 Note
If the re is an elect ronic mal func tion, servotronic will s till f unction
li ke a conven tional power steering system, p rovid ing a constant
steering support fo rce that is no longer proportionate to the ve hicle
spee d. This is most noticeab le whe n tur ning the s teer ing whe el at low
speeds ( for example when park ing), -more effort will be required
t h a n usual.
• Be aware o f the d ifferent than usual steering response and adjust
your st eering force a ccordi ng ly.
• Have the prob lem checked and set r ight by an autho rize d Aud i
dealer as soo n as possib le.
• If a steering ma lf u nction occ urs, t his is signaled w ith the or. ~
indicator l igh ts a nd a wa rning tone, see .
[I] Tips
• If the powe r stee ring system shou ld fa il, or if the engine is not
run ning (for example, while being towed), you w ill still be ab le to
stee r the veh icle. However, more effort wi ll be required to do so . .,.
Vehicle care Do-it-yourself service Technical data

Intelligent technologyL _______________________________________ _
• If the power steering system is not funct ioning properly, contact
your au thori zed A ud i dea le r i mmediately. •
Applies to ve hicl es: wit h A ll Whe el D rive
Driving with your quattro®
With All Wheel Drive, all four wheels are driven.
General information
With All Wheel Drive, power is distributed to all fo ur whee ls. This
happens automatically depending on you r driving s tyle a nd the road
conditions at the time. See also =>
page 189, "Electronic differential
lo ck (E DL)".
W inter tires
W hen d riving in the winter, your vehicle with A ll Whee l Drive has an
advantage, even with reg ular t ires . In winter road cond it ions it may
be advisab le to mou nt w inte r ti res (or all-se aso n t ires) for imp roved
dr iveability and braking: these tires must be mounted on
all four
wheel s.
See also => page 261, "Win ter tires".
Snow chains
W he re snow c ha ins are mand atory on certain roads, this norm ally
also app lies to veh icles with all-wheel drive=>
page 262, "Snow
c hains".
Replacing wheels/tires
Veh icles with All Wheel Drive m ust always have t ires of the same s ize.
Also avoid tires with different tread depths. For details see page
=>
page 257, " N ew tires and replac ing ti res and wheels".
Off-Road driving?
Your Audi does not have enough ground clearance to be used as a n
off-road vehicle. It is therefore best to avoid rough tracks and uneven
te rrain as much as poss ib le. Also refe r to=>
page 199.
& WARNING
Always adjust your driving to road and traffic conditions . Do not
let the extra safety afforded by the all-wheel drive tempt you into
taking extra risk s.
• Although the quattro ®all -wheel drive is very effective, always
remember that braking capacity is limited by t ire traction. You
should therefore not drive at exce ssive speed s on icy or slippery
road surfaces .
• On wet road surfa ces, be careful not to drive too fast becau se
the front wheels could begin to slide on top of the water (hydro­
planing ). If this should occur, you will have no warning from a
sudden increase in engine speed as with a front -wheel drive
vehicle. Always dr ive at speed s which are adjusted to the road
conditions -risk of crash! •
Energy management
Starting ability is optimized
Energy managemen t controls the distribution of elec ­
trical energy and thus optimizes the availability of elec­
t r ical ene rgy for s tarting the en gin e.
If a vehicle w ith a convent ional energy sys tem is not d riven fo r a long
period of time, t he battery is discha rged by idling cur rent consumers
(e .g. immob ilizer). In ce rtain c ircumstances it can result i n there
being insufficient energy availab le to start the engine .
Inte lligent ene rgy m anageme nt in yo ur vehicle h andles the dis tribu­
tion of electrical energy. Starting ability is markedly improved and
t he life of the bat tery is ex tende d.
Bas ically, energy management consis ts of
battery d iagnosis, idling
current management
and dynamic energy management . ~