spare tire AUDI S3 2015 User Guide

266 Tire s and wheels
& WARNING
-If the tire pressure warning light ti] in
the instrument cluster turns on, the
pressure in one or more tires is too low.
Reduce the vehicle speed immediately
and avoid any hard steering or braking
maneuvers . Stop as soon as possible,
check the t ire and inflate the tire to the
correct pressure, which is specified on
the tire pressu re label on the veh icle
¢ page 240. Driving with a t ire with low
pressure causes the tire to overheat and
can result in failure of the tire . Low pres ­
sure can a lso have a negative effect on
the driving and braking behavior of the
vehicle.
- The driver is responsible for maintaining
the correct tire pressures. You must
check the t ire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor ind i­
cator may be delayed .
- Ask your author ized dealer if run-flat
t ires may be used on your vehicle.
- The tire pressure monitoring system can
also stop work ing when there is an ESC
malfunction.
- Using snow chains may result in a system
malfunction.
- The tires with the identification "AO" or
"RO" ¢ page 254 have been matched
with your Audi tire pressure monitoring
system. We recommend that you use
these tires.
- The tire pressure monitoring system can
only mon itor the t ire pressure of the
driving tires . Check the tire pressure of
the spare wheel in the luggage compart­ ment so that if necessary it is ready for
us e.
-
Storing tire pressures
Applies to vehicles: wit h tire press ure mo nitor ing system
A change in tire pressure or a change in tires
must be stored in the system.
The tire pressure is stored in the MMI.
.. Make sure before storing that the tire pres ­
sures of a ll four tires meet the specified va l­
ues and are adapted to the load. Otherwise
the system could malfunction
¢ page 240.
.. Switch on the ignition.
.. Select: the
I MENU I button >Car > Systems*
control button > Service & control > Tire
pressure monitor > Store tire pre ssure >
Yes, store now.
(D Tips
Do not store the tire pressures if snow
chains are installed. Otherwise the system
could malfunction.

268 What do I do n ow ?
Equipment
Vehicle tool kit
Applies to vehicles: with vehicle tool kit
Fig . 175 Luggage compart ment: cargo floor cover
folded upward
The vehicle tool kit is located in the luggage
compartment under the cargo floor cover
¢fig. 175 .
Carg o flo or c over
.. Hang the plastic hook on the luggage com­
partment weather str ip -arrow-.
Spare tire
General information
Applies to vehicles: with space-saving spa re tire (compact
spare tire)
Fig. 176 Luggage compartment: cargo floor cove r
fo lded upward
Fi g. 177 Compact spare tire
The spare tire~ fig. 177 is intended for short­
term use only. Have the damaged tire checked
and replaced if necessary by an author ized
Audi dealer or qualified repair facility as soon
as possible.
There are some restrictions on the use of the
compact spare tire. The compact spare tire
has been designed specifically for your type of
vehicle. Do not replace it with the spare tire
from another type of vehicle.
Rem ovi ng the sp are tir e
.. Lift the cargo floor by the plastic handle.
.. Hang the p lastic hook on the luggage com­
partment weather strip@¢
fig. 176 .
.. Remove the subwoofer*, if necessary
¢page 269.
.. Turn the large screw counter-clockwise.
.. Remove the spare tire.
Snow ch ain s
For technical reasons, the use of snow chains
on the compact spare tire is not permitted.
If you have to drive with snow chains and a
front tire fails, mount the spare wheel in place
of a rear tire. Install the snow chains on the
rear tire that you removed, and install that in
place of the front tire that failed .
A WARNING
--After installing a spare tire, the tire pres-
sure must be c hec ked as soon as possi­
b le. The tire p ress ure is available on
¢ page 240, fig. 169
- If the spa re tire is more t han 6 years old,
use it only in an emergency and with ex­
treme caution and careful driving.
- The spare ti re is intended only for tem­
pora ry and short-term use.
It shou ld be
replaced as soon as poss ible with the
normal wheel and tire.
- After mounting the compact spare tire, the tire pressure must be checked as
soon as possible . The tire pressure of the
compact spare tire must be 4.2 bar; oth­
erwise, you risk having an accident.

....,
N
0 > co
rl I.O
"' ....,
"' rl
-Do not drive faster than 50 mph (80 km/
h). You r isk having an accident.
- Avoid full-throttle acceleratio n, heavy
braking, and fast cornering . You risk hav­
ing an acc ident.
- Never drive us ing more than one spare
wheel and tire. You risk having an acci­
dent.
- Normal summer or winter tires must not
be mounted on the compact spare whee l
rim.
- For technical reasons, the use of tire
chains on the spare tire is not permitted.
If it is necessary to dr ive with tire chains,
the spare wheel must be mounted on the
front axle in the event of a flat in a rear
t ir e. The newly ava ilable front wheel
must then be i nstalled in pla ce of the
re ar wheel with the f lat tir e. Ins tall ing
the tire chai n befo re mo unting the wheel
and tire is recommended .
- Loose items in the passenger compart­
ment can cause serio us personal inj ury
dur ing hard braking or in an accident.
Never store the inf latable spare tire or
jack and tools in the passenger compart­ ment.
- Norma l summer or winter tires m ust not
be mounted on the compact spare wheel
rim .
Removing the subwoofer
App lies to vehicles : with subwoofer
The subwoofer must be removed before the
spare wheel* can be removed .
Fig. 178 Spa re whee l w ell : subwoo fer
What do I do now ? 269
Removing the subwoofer
.,. Lift the cargo floor¢ page 268, fig . 176.
.,. Pull the latch (D ¢ fig. 178 toward the ca -
ble.
.,. Press the locking tab @down .
.,. Remove the connector ® and set the re-
moved cable as ide .
.,. Remove the bolt @ .
.,. Carefully remove the subwoofer .
Installing the subwoofer
.,. Carefully place the subwoof er n the rim
wel l. The word "FRONT" on the subwoofer
must face forward.
.,. Insert the connector that was removed.
.,. Secure the subwoofer with the bolt .
.,. Fold the cargo floo r cover back into place.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger 's safety when chang ­
ing a wheel .
.,. Aft er you experience a tire failure, pull the
car we ll away from mov ing traffic and try to
reac h
level ground before you stop ¢ &_ .
.,. All passenge rs should
leave the car and
move to a safe location (for instance, behind
the guardrail)¢ &_ .
.,. Engage the
parking brake to prevent your
veh icle from rolling unintentionally¢&_ .
.,. Move
sel ector lever to po sition P ¢ ,&. .
.,. If you are towing a t ra iler, unhi tch the trailer
from your ve hicle .
.,. Take t he
jack ¢ page 268 and the sp a re tire
¢ page 268 out of the luggage com part ­
ment .
A WARNING
You or your passengers could be inj ured
while changing a w heel if you do not fo l­
l ow these safety p recaut io ns:
- If you have a flat tire, move a safe d is­
tance off the road. Turn off the engine,
turn the emergency flashers on and use

2 70 What do I do now ?
other warning devices to alert other
motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- To help prevent the ve hicle from mov ing
sudden ly and possibly slipping off the
jack, always fully set the parking brake and block the whee l diago na lly opposite
the whee l being changed . When one
front whee l is lifted off the gro und, plac ­
ing the A utomat ic Transm iss ion in P
( P ark) will
no t prevent t he ve hicl e from
movin g.
- B efore yo u change a w heel, be su re the
gr ound is leve l and fir m.
If necess ary,
use a s turdy board under the j ack.
- Alw ay s store the vehicle tool ki t, the j ack
and the repl aced t ire i n the l ugg age com­
partment
¢ page 131.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by -step and in
exactly that order.
1. Remove the decorative wheel cover* . Fo r
mo re details see also¢
page 2 70, Deco­
rative wheel covers
or ¢ page 2 71 ,
Wheels with wheel bolt caps .
2. Loosen the wheel bolts r::!> page 271.
3 . Locate the proper mo unting point for the
jack and align the jack below that point
¢ page 272.
4 .
Raise the car w ith the jack ¢ page 2 72.
5. Remove the wheel with the flat tire and
then install
the spare ¢ page 2 73.
6. Tighten all wheel bo lt s li ghtly.
7 .
Lower the ve hicle w ith the jack.
8. Use the wheel bolt wrench and
firmly
t ig hten all whee l bolts <:!> page 271.
9. Replace the decorative wheel cove r* .
A WARNING
A lways read and follow all WARNINGS and
informati on
r::!> &. in Raising the vehicle on
page
2 72 a nd r:!> page 274 .
After changing a wheel
A wheel change is not complete without the
doing the following .
"'Always store the vehicle toot kit, the jack*
and the replaced tire in the luggage com­
pa rtment
¢ page 131.
"' Check the tire pr essure on the spare whee l
immed iate ly afte r mounting i t.
"' As soon as poss ib le, have the
tight ening
torques
on all whee l bolts chec ked with a
torque wre nch . The correc t tig hten ing tor ­
que is 90 ft l b (120 Nm).
"' Have the flat tire
replaced as soon as possi­
ble.
@ Tips
- If you not ice that the wheel bo lts are
corroded and difficult to turn while
chang ing a tire, t hey should be rep laced
before you check the tig htening to rque.
- Dr ive at reduced speed until you have the
t ightening torques checked.
- After changing a whee l, the t ire p ress ure
in all four tires must be chec ked/co rrect­
ed and the tire p ress ure monito ring ind i­
cator must be s to red in the MMI
r::!> page 266.
' Decorative wheel covers
Applies to vehicles: w ith decorative whee l covers
The decorative wheel covers mus t be removed
first to access the wheel bolts.
Fig. 1 79 Cha ngin g a w hee l: Re mov ing th e w heel cove r
Removing
"' Insert the hook (p rov ided with th e vehicle
t oo l ki t) in the ho le in the whee l hub cover . .,._

274 What do I do no w?
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
Never use the hexagonal socket in the han ­
dle of the screwdriver to loosen or t ighten
the wheel bolts.
- Pull the reversible b lade from the screw­
driver before yo u use the hexagonal
socket in the handle to turn the whee l
bo lts.
- When mounting tires with
unid irectional
tread design
make sure the tread pat­
tern is pointed the r ight way
¢page 274.
- The wheel bolts should be clea n and easy
to tu rn . Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the h ub. Remove a ll dirt from these
su rfaces before remo unti ng the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern p ointed in
the right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a sp are tire w ith a tread pa tte rn
i nten ded for use in a specific direc tion, p lease
note t he following:
- T he direction of rotation is marked by an a r­
row on the side of the tire.
- If the spare t ire has to be installed in the in­
c orrec t direction, use the spa re tire only
tempor arily si nce the t ire will no t be able to
achieve its op timum performance character­
istics with regard to aquaplaning, noise and
wear .
- We recommend tha t you pay particular a t­
tention to this fact during wet weather and
that you adjust your speed to matc h road
condit ions. -
Replace the flat ti re with a new one and
have it insta lled on your vehicle as soo n as
possible to resto re the hand ling advantages
of a unidirectional tire.
Notes on wheel changing
Please read t he information ¢ page 254, New
tires and replacing tires and wheels
if you a re
going to use a spa re tire which is different
from the t ires on you r vehicle.
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after installation .
- Have the wheel bolt tightening torque
c hecked with a torque wrench as soon as
possible by your author ized Audi dealer or
a qualified service stat ion.
- With steel and alloy wheel r ims, the wheel
bolts a re co rrectly tightened at a torque of
90 ft lb (120 Nm ).
- If you notice that the wheel bolts are cor ­
roded and difficult to turn while changing
a tire , they should be replaced before you
check the t ightening torque .
- Replace the flat tire w ith a new one and
have it installed on your vehicle as soon as
po ssible . Remount the wh eel cover.
Until then , dr ive with e xtra care and at re­
duced speeds.
A WARNING
= -
- If you are going to equ ip your vehicle
with tires o r rims which differ from those
which were facto ry installed, then be
s ure to read the information¢
page 25 4,
New tires and repla cing tires and
wheels.
- Always m ake s ure the dam age d wheel o r
even a flat tire a nd the jack and tool ki t
are properly secu red in the luggage com­
pa rtment and are not loose in the pas ­
senger compartment.
- In an accident or sudden maneuver they
could fly forwa rd, injuring anyone in the
veh icle.

M N
0 > co ,...., \!) ..,.,
M ..,., ,....,
in P (Park position) and the park brake is
applied.
@ For the sake of the environment
-Changing the engine settings wi ll ad ­
versely affect emission levels . This is det­
rimenta l to the environment and increas­
es fue l cons umption .
- Always observe env ironmental regula­
tions when dispos ing of old engine oil,
used brake fluid, dirty engine coolant,
spent batter ies or worn out tires.
- Undeployed airbag modules and preten­
s ioners might be classified as Perchlo­
rate Material -spec ial handling may ap­
ply, see www .dtsc .ca .gov/hazardous­
waste/perch lorate . When the veh icle or
parts of the restraint system includ ing
airb ag mod ules safety be lts wit h preten­
s ioners are scrapped, all applic able laws
and regulations must be observed. Your
a utho rized Audi dea le r is familiar with
these req uirements and we recommend
that you have your dealer perform this
serv ice for you .
Additional accessories,
modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories .
Your vehicle incorporates the latest safety de ­
sig n features ensuring a high standard of ac­
tive and passive safety .
This sa fe ty could be compromised by non-ap­
proved changes to the veh icle . For this reason ,
if pa rts have to be replaced, p lease observe
the following points when install ing addition­
a l acc essories:
Approved Audi accessor ies and genuine Audi
pa rts are ava ilable from authorized Aud i deal­
ers .
Con sumer In formation 29 1
These dea le rs a lso have the necessary facili ­
ties, tools a nd trained specialists to install the
parts and accessories properly .
_& WARNING
Using the wrong spare parts or using non­
approved accessories can cause damage to
the vehicle and ser ious persona l injury .
- Use on ly accessories express ly approved
by Audi and ge nuine Audi spare parts
- These parts and accessories have been
specially designed to be used on your ve­
hicle .
- Never install accessor ies such as tele­
phone crad les or beverage ho lders on air­
bag covers or w ithi n the airbag deploy­
ment zones. Do ing so wi ll increas e the
ris k of injury if a irbags are triggered in an
accide nt!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNIN GS
<:!) page 217.
(D Note
-If items other than ge nuine Audi spare
parts, add-on equipment and accessory
items are used o r if repair wo rk is no t
perf ormed ac cord ing to spe cified meth­
ods, this ca n resu lt in seve re dam age to
your vehicle's engine and bo dy (such as
co rrosion) an d adve rsely affect yo ur vehi­
cle 's warranty .
- If emergency repairs must be performe d
elsewhere , have the vehicle examine d by
an authorized A udi dealer as soon as
possible.
- The manufacturer cannot be held liable
for damage wh ich occ urs due to failure
to comply with these stipu lations.
Technical Modifications
Our guidelines must be complied with when
technical modifications are made.
A lways consult an authorized Audi dealer be-
-
fore start ing work on any modifications. ..,_
•
•