warning AUDI S3 2015 Workshop Manual

....,
N
0 > co
rl I.O
"' ....,
"' rl
Starting and stopping
the engine (vehicles
with a convenience key)
St t· th · ith the
button
Applies to vehicles: with convenience key
The I START ENGINE STOPI button switches
the ignition on and starts the engine.
Fig. 71 C en ter con sole : START ENGINE STOP b utton
(w ith conve nien ce key)
You can start your car without using your con­
venience key. You must simply be carry ing the
key with you.
Switching the ignition on/off or
prewarming
If the 'y.ij indicator light blinks and the mes­
sage
Please move steering wheel appears
when switching the ignition on, the steering is
locked by the steering lock . In this case, turn
the steering wheel slightly to the left/r ight .
.,. To switch the ignition on or off, press the
I START ENGINE STOPI button . Do not press
the brake pedal while do ing this .
Diesel vehicles are preheated while the igni­
tion is switched on
II.
Starting the engine
Your vehicle is equipped with launch contro l.
The engine starts automatically when you press the
I START ENGINE STOP I button brief­
ly .
.,. Press the brake pedal and move the se lector
lever to the P or N position.
.,. Press the
I START ENGINE STOPI button
briefly. The engine will start .
Driving 77
Major electrical equipment switches off tem­
porarily when starting the engine.
It is possible that there will be a slight delay
when starting the engine in diesel vehicles in
colder temperatures. Therefore, you must
hold the brake pedal down until the engine
starts. The indicator light turns on wh ile the
engine is preheating
II .
The prewarming time depends on the coolant
temperature and outside temperature . The
glow plug indicator light
II will only turn on
for approximately 1 second when the engine
is warm or the outside temperature is higher
than 8
°C. That means you can start the en ­
gine
immediately.
If the engine does not start immediately, stop
the start ing procedure by pushing the
I START ENGINE STOP I button again and re­
peat after
30 seconds.
Automatic start malfunction
If the GI (gasoline engine) or II (diesel en­
gine) indicator light turns on when you start
the engine, there is an automatic start mal­
funct ion .
To start the engine, press and hold the
I START ENGINE STOP I button until the engine
runs .
Drive to an authorized Audi dealer or author ­
ized Audi Service Facility immediately to have
the malfunction corrected .
A WARNING
-Never allow the engine to run in confined
spaces - danger of asphyx iat ion.
- Always take the vehicle key with you
when leaving the vehicle, even for a
short period of time. This applies part ic­
ular ly when children remain in the vehi­
cle . Otherwise the children could start
the engine or operate electrical equip­
ment such as power windows .
- Please note that the brake booster and
power steering only work when the en-
gine is running. When the engine off, you
~

78 Driving
must use more force to steer or brake
the vehicle. Because the usual steering
and braking capability is not available,
the risk of accidents or injuries increases .
- Avoid high engine speed, full throttle,
and heavy engine load as long as the en­
gine has not reached operating tempera­
ture yet. You could damage the engine .
- The engine cannot be started by pushing
or towing.
@ For the sake of the environment
Do not let the engine run while parked to
warm up. Begin driving immediately. This
reduces unnecessary emissions.
{D) Tips
- After starting a cold engine, there may
be a brief period of increased noise be­
cause the oil pressure must first build up in the hydraulic valve adjusters. This is
normal and not a cause for concern .
- If the . indicator light blinks in the in­
strument cluster before switching the ig ­
nition off, the ignition will not switch on
again.
9 page 193
- If you leave your vehicle with the ignition
switched on, the ignition will switch off
after a certain amount of time. Make
sure that electrical equipment such as
the exterior lights are switched off.
Turning the engine off using the button
Applies to vehicles: with conven ience key
• Bring the vehicle to a full stop.
• Move the selector lever into the P position .
• Press the
I START ENGIN E STOPI button
9page 77, fig. 71 .
Steering lockll
The steering locks when you turn the engine
off using the
I START E NGIN E STOP t* button,
l) Thi s fun ction is not available in all c oun tries.
move the selector lever into the P position
and open the driver's door.
The locked steering helps prevent vehicle
theft .
Emergency off function
If it is absolutely necessary, the engine can al­
so be turned off while driving at speeds lower
than 6 mph (10 km/h). If you press the
I STAR T ENGINE ST OPI* button while driving,
the message
Pressing start/stop button
again will switch off engine!
appears. To
switch the engine off, press the
I S TAR T ENGINE ST OPI* button twice in a row
briefly or press and hold for longer than two
seconds.
A WARNING ~
- Never turn off the engine before the ve- hicle has come to a complete stop . The
full function of the brake booster and the
power steering is not guaranteed . You
must use more force to turn or brake if
necessary. Because you cannot steer and
brake as you usually would, this could
lead to crashes and serious injuries.
- Please note that the brake booster and
power steering only work when the en­
gine is running. When the engine off, you
must use more force to steer or brake
the vehicle. Because the usual steering
and braking capability is not available,
the risk of accidents or injuries increases.
- Always take the vehicle key with you
when leaving the vehicle, even for a
short period of time. This applies partic­
ularly when children remain in the vehi­
cle . Otherwise the children could start
the engine or operate electrical equip­
ment such as power windows.
- For safety reasons, always park the vehi­
cle with the selector lever in the P posi­
tion. Otherwise, there is the risk that the
vehicle could roll.

....,
N
ci > co
rl I.O
"' ....,
"' rl
-After the engine has been switched off ,
the radiator fan can continue to run for
up to 10 minutes -even with the ignition
switched off . It can also switch on again
after some time if the coolant tempera­
ture rises as the result of heat buildup or
if the engine compartment is heated by
the sun's rays and the engine is hot.
(D Note
If the engine has been under heavy load
for an extended period of time, heat builds
up in the engine compartment after the
engine is sw itched off -there is a ris k of
damaging the engine. For this reason, let
the engine run for at idle for approx imate ­
ly two minutes before shutting it off.
Starting the engine if there is a
malfunction
App lies to vehicles: with conve nience key
It may not b e possibl e to start the engine un­
der cer tain circumstances , for example if the
battery in the vehicle key is drained , if inter­
ference is affected the key or if there is o sys ­
tem mo/function.
Fig. 72 Steering co lu m n/re mote control key : Start ing
the engine if there is a ma lfunctio n
As long as the message f>l) Key not recog­
nized. See owners manual
appears, you can
start your vehicle using the emergency start
function .
"" Press the brake pedal¢.&.
in Starting the
engine with the
START ENGINE STOP but­
ton on page
77 .
.,. Press the
j;..,, s=T~A~R=T~-EN~G-I_N_E--ST--OP I button.
Driving 79
""Ho ld the master key as shown in the illustra­
tion in the location indicated
y>>) r=) fig. 72.
The engine w ill start.
"" If the engine does not automatically start,
press the
I START ENGINE STOP I button
again .
Drive to an authorized Audi dealer or author­
ized Audi Service Facility immediately to have
the malfunction corrected.
(D Tips
You can display the message that appears
during an emergency by pressing the
I START ENGINE STOP!* button.
Driver messages
Turn off ignition before leav ing car. Battery
is discharging
This message appears and a warning tone
sounds if you open the driver's door when the ignition is switched on. Switch the ignition off
so that the battery will not discharge.
Pressing start/stop button again will switch
off engine!
T his message appears when you press the
I STAR T ENGINE S TOPI* button while driving
¢ page 78, Emergency off function .
Engine start system malfunction. Please
contact Service
The engine automat ic start system has a ma l­
funct ion. Drive to an authorized Audi deale r or
authorized Aud i Service Facility immediately
to have the malfunction corrected . To start
the engine, press and hold the
I STAR T ENGINE S TOP I button.
DJ Key not recognized. See owner's manual
This message appears if there is no conven­
ience key inside the vehicle or if the system
does not recognize the key. The convenience
key may no t be recogn ized, for example, if it is
covered by an object that
disrupts the signal
(such as a briefcase), or if the key battery is
weak. E lectronic devices such as ce ll phones
can a lso interfere with the signal. ..,.

M N
0 > co ,...., \!) ..,.,
M ..,., ,....,
driving force has been built up at the
whee ls.
E mergenc y brake fun ction
An emergency braking funct ions ensures that
the vehicle can be slowed down even if the
normal brakes fail¢ page 82, Emergency
braking function .
A WARNING
-Do not press the accelerator pedal inad­
vertent ly when the vehicle is stationary
and the engine is runn ing and a gear is
selected. Otherwise the vehicle will start
to move immediately and could result in a crash .
- If the power supply fa ils, the re leased
park ing brake can no longer engage. In
this case, par k the vehicle on level
ground and secure it by placing the se­
lector lever i n the P pos ition. See an au­
thori zed Aud i dea ler or a utho rized Aud i
Serv ice Facility for ass istance.
(D Note
I f the . or. (U SA mode ls) /. (Cana­
da mode ls) indicato r light in t he instru­
ment cluster blinks, there is a mal fun ct ion
in the brake system . Re fer to the detailed
description of the indicator lights
r=:>page 18.
-If the . (USA models) /. (Cana-
da models) or
Iii indicator light turns
on, there is a malfunct ion in the park ing
brake
r=:> page 19.
(D Tips
- If the electromechanical parking brake is
set wh ile the ignition is switched off, the
¢C)'A indicator light in the button and in
the instrument cluster dis- play . (USA models)
I. (Cana-
da models) w ill t urn off afte r a ce rtain
amount of time.
- If dr iver's door is opened while the ign i­
tion is switched on, the parking b rake
sets automat ically. This prevents unin­
tended ro lling of the vehicle .
Dri vin g 81
-Occasional noises when the pa rking
brake is set and released are normal and
are not a cause for concern.
- When the vehicle is pa rked, the park ing
brake goes through a self -test cycle at
regu lar interva ls. Any no ises assoc iated
w ith this are normal.
- If there is a power fa ilure, the park ing
brake will not set if it is released, and it
w ill not release if it is set
r=;, & . See a n
authorized Audi dealer or autho rized
Audi Service Facility fo r ass ista nce.
Parking
" Press the b rake pedal to stop the veh icle.
" Pull the switch @¢
page 80, fig. 73 to set
t he par king brake.
" Place the se lecto r lever in the P position .
.. Turn the engine off¢
A_.
"Tu rn the steering wheel when parking on in­
clines so that the wheels w ill roll into the
curb if the vehicle starts moving.
A WARNING
- Always take the vehicle key w ith you
when leav ing the vehicle, even for a
short pe riod of time. This applies part ic­
ularly when children rema in in the veh i­
cle . Ot herwise children co uld s tart the
engine, release the pa rking brake o r op ­
erate electrical equipment such as power
windows, which increases the risk of an
accident.
- No one should remain in the vehicle
when it is locked, especially children.
Loc ked doors make it more difficult for
emergency workers to get into the ve hi­
cle, which puts lives at risk.
•

82 Driving
Starting from a stop
The start assist function ensures that the
parking brake is released automatically upon
starting.
St opping and sett ing the p ark ing br ake
.. Pull the switch@¢
page 80, fig. 73 to set
the parking brake.
St arting a nd aut omaticall y relea sing the
pa rking br ake
Requirement: The driver's door must be
locked and the driver's safety belt must be
fastened.
.. When you press the accelerator pedal, the
parking brake is automatically released and
your vehicle begins to move.
When stopping at a traffic signa l or stopping
in city traffic, the parking brake can be ap­
plied. The vehicle does not have to be held
with the brake pedal. The parking brake elim i­
nates the tendency to creep when a selector
l ever pos ition is engaged . As soon as you
press the accele rator pedal, the parking bra ke
re leases automatically and the veh icle starts
to move.
Starting on slope s
When starting on incl ines, the hill start ass ist
prevents the vehicle from unintentiona lly roll­
i ng back. The braking force of the parking
brake is not released until sufficient dr iving
force has been bu ilt up at the whee ls.
(D Tips
For safety reasons, the park ing brake is re ­
leased automatically only when the dr iv­
er 's sa fety belt is fastened and the driver 's
door is locked. Emergency braking function
This is used if the conventional brake system
fails or locks up .
.. To brake your vehicle in an emergency, pull
the @switch ¢
page 80, fig. 73 and hold it
pulled .
.. As soon as you release the@ switch or ac-
celerate, the b rak ing process stops.
Pul ling and ho ld ing the @switch while dr iv ­
ing at a speed of about 2 mph (3 km/h) or
higher init iates the emergency braking func­
t ion. The vehicle is braked at a ll four wheels
by activating the braking hyd rauli cs . The brake
performance is sim ila r to heavy braking.
~ .&.
To he lp prevent activating the emergency
braking by mistake, a n aud ible war ning tone
(buzzer) sounds when the @switch is pulled .
Emergency brak ing stops as soon as the@
swi tch is re leased or the acce lerator pedal is
pressed.
.&, WARNING ,_
Emergency braking should only be used in
an emergency, when the normal brake pedal has fa iled or the brake pedal is ob­
structed. During emergency brak ing, your
vehicle will brake s imilar to heavy b rak ing .
E SC and the associated components (ABS,
ASR, EDL) canno t overcome the laws of
physi cs. In corne rs and when road or
weather conditions are bad, a fu ll brake
application can cause the vehicle to skid or
the rea r end to break away, which increas­
es the risk of an accident.
Hill hold
Applies to veh icles : w ith Hill Hold
Hill hold makes it easier to start on hills.
Req uirement: The dr iver door mus t be closed
and the engine must be running.
T he system is activated when the bra ke peda l
is p ressed while the vehi cle is stationa ry.
T o p revent the vehicle from rolling back when
sta rting, the b rake power is held fo r a b rief
ll>

M N
0 > co ,...., \!) 1.1'1
M 1.1'1 ,....,
moment after re leasi ng the b rake peda l. Dur­
i n g this time, you can easily be gin to move
your veh icle.
A WARNING
- The intelligent technology of Hill Hold
cannot overcome the lim itations im­
posed by natural phys ica l laws . The in­
c reased comfort offered by Hill Hold
sho uld not cause you to ta ke safety risks .
- Hill Hold cannot hold the veh icle in all
hill start situat ions (for examp le, if the
ground is slippery or icy).
- If you do not begin movi ng immediately
after releasing the b rake pedal, the vehi­
cl e could begin to roll backwa rd under
c ertai n circumst ances. Press the bra ke
peda l or set the par king b rake immed i­
ately .
-If the engine "sta lls", p ress the brake
peda l or set the par king b rake immedi ­
ately .
- Star ting on in cli nes in s top-and-go traf­
fic: To hel p prevent the vehicle from roll ­
ing back when starting, press and hold
the brake pedal for several seconds when
the vehicle is stationary.
@ Tips
You can find out if your vehicle is equipped
wit h Hill Hold by check ing at an authorized
Aud i dea le r or q ualified repa ir facility.
Speed warning system
Introduction
The speed warning system helps you to stay
under a specified maximum speed.
-
The speed warning system warns you if you
are exceeding the max imum speed that you
h ave set . Yo u will hea r a warn ing tone when
your speed exceeds the stored va lue by ap­
p rox imately 3 mph (3 km/ h). The . (USA
models)/ . (Canad a mo dels) indicator l igh t
and the message
Speed limit e xceeded! ap­
pear in the instr ument cluster disp lay at the
same time. The./. indicator light turns
Drivin g 83
off when the speed dec reases be low the stor ­
ed maximum speed .
Setting a t hreshold is recommended if you
would like to be rem inded when you reach a
ce rtain maxim um speed. S ituations whe re you
may want to do so incl ude driving in a co untry
with a genera l speed limit o r if the re is a
specified maximum speed for winter tires .
(D Tips
Regardless of the speed warning system,
you should a lways monitor your speed us­
i ng the speedometer and make sure yo u
are follow ing the lega l speed limit .
Setting the threshold
You can set, change and delete the threshold
in the MMI.
.,.. Select: the
I MENU I button > Car > Systems*
cont ro l button > Driver assistance > Speed
warning .
You can set any threshold between 20 mph
(30 km/h) and 150 mph (240 km/h) . Settings
can each be adj usted in increments of 6 mph
(10 km/h).
Cruise control system
Description
Applies to veh icles: w ith c ruise control system
The cru ise con trol system makes it poss ib le to
drive at a cons tant speed start ing at 15 mph
(20 km/h).
T he speed is kept const ant by modifying en­
gine powe r or throug h an ac tive brake inte r­
vention .
.&_ WARNING
-Always pay attention to the t raffic
around you when the cruise contro l is in
operation. You are always responsible for
your speed and the distance between
your veh icle and other vehicles .
llll-
•

84 Driving
-For reasons of safety, cruise control
should not be used in the city, in stop­
and-go traffic, on winding roads and
when road conditions are poor (such as
ice, fog, gravel, heavy rain and hydro­
planing) -you could have an accident .
- Switch the cruise control off temporarily
when driving in turning lanes, highway
exits or in construction zones.
- Please note that unconsciously "resting"
your foot on the accelerator pedal pre­
vents the cruise control from braking.
This is due to the control system being
overridden by the driver's acceleration.
- If there is a brake system malfunction
such as overheating when the speed
warning system is switched on, the brak­
ing function in the system will be deacti­
vated. The remaining speed warning sys­
tem functions will remain active, as long
as the
B (USA models)/ ii (Canada
models) indicator light is on.
@ Tips
- The cruise control system is ideal for
stretches with speed limits. The driver is
responsible for adhering to the correct
speed.
- The cruise control remains active when
shifting gears.
- The brake lights turn on when the brakes
are activated.
Switching on
Applies to vehicles: with cr uise contro l system
0
f
~
0
Fig. 74 Opera ting lever: Cruise control system
.,. To switch the cruise control on, pull the lev­
er into position
CD¢ fig. 74.
.,. Drive at the speed to be maintained.
.,. To store the speed, press the button @. The
B (USA models)/ ii (Canada models)
turns on in the instrument cluster.
Changing speed
Applies to vehicles: with cruise control system
.,. To increase or decrease the speed in incre­
ments,
tap the lever in the 0 10 direction
<:;>page 84, fig. 74 .
.,. To increase or decrease the speed quickly,
hold the lever in the 010 direction until
the desired speed is reached.
Overriding the speed
You can press the accelerator pedal down to
increase your speed, for example if you want
to pass someone. The speed you saved earlier
will resume as soon as you release the acceler­ ator pedal.
If, however, you exceed your saved speed by 5
mph (10 km/h) for longer than 6 minutes, the
cruise control turns off temporarily. The
II
(USA models) / Bl (Canada models) indicator
light in the instrument cluster turns off and
the stored speed is retained .
Preselecting the speed
Applies to vehicles: with cruise control system
You can preselect your desired speed when
the vehicle is stationary .
.,. Switch on the ignition .
.,. Pull the lever into position
CD¢ page 84,
fig . 74.
.,. To increase or decrease the speed, tap the
lever in the
010 direction .
This function makes it possible, for example,
to save the speed you want before driving on
the highway . Once on the highway, activate
the cruise control by pulling the lever toward
CD-

M N
0 > co ,...., \!) ..,.,
M ..,., ,....,
Switching off
Applies to vehicles: with cruise contro l system
Temp orar y de acti vation
.. Press the brake pedal, or
.. Press the lever into pos ition @ (not clicked
i nto place) ~
page 84, fig. 74, or
Switchin g off completel y
.. Press the lever into pos ition @ (clicked into
place), or
.. Switch the ign ition off .
The speed you stored will be retained if the
cru ise control has been sw itched off tempora­
rily. To resume the stored speed, release the
brake pedal and pull the lever into posit ion
@ .
The stored speed is erased when the cru ise
control is switched off completely or the ign i­
tion is sw itched off .
.8, WARNING
You should only resume the stored speed if
it is not too h igh fo r exis ting traffic condi­
tions. Otherwise you risk an accident .
@ Tips
-If the brakes become too heated while
driving, the cruise cont ro l switches off .
If
this happens while dr iv ing downh ill, you
can re lieve the brakes by shifting into a
l ower gear .
- When the cr uise control is act ivated, ESC
spo rt mode cannot be switched on.
Dri vin g 85
•

86 Audi adapti ve cruise control
Audi adaptive cruise
control
Introduction
Applies to vehicles: with Audi adaptive cruise co ntrol
The adaptive cruise control system is a combi­
nation of speed and distance regulation. It as­
sists the driver by both regulat ing the speed
and maintaining a distance to the object
ahead, within the abilit ies of the system. If
the system detects an object, adaptive cru ise
con trol can brake and acce le rate your veh icle.
This makes driving more comfortable both on
long stretches of highway and in stop-and -go
traffic.
General Information
General information
Applies to vehicles: with Audi adaptive cruise control and
Audi pre se nse front
Fi g. 75 Front of veh icle: sensor
The genera l information applies to adaptive
cruise control * and pre sense front *
c:;, page 94.
The radar sensor a rea c::> fig. 75 m ust not be
covered w ith stickers, deposits or a ny other
obstructions as it may impair the function of
the adaptive cruise control and the pre sense
front. For information on cleaning, refer to
c:;, page 205. The same applies for any modifi­
cations made in the front area.
The function of the adaptive cruise control
system and pre sense front is limited in some
conditions : -
Objects can on ly be detected when they are
within the sensor range
c::> page 87,
fig. 78.
-The system has a limited ability to detect
objects that are a short distance ahead, off
to the side of your vehicle or moving into
your lane.
- Objects that are difficult to detect such as
motorcycles, vehicles with high ground
clearance or an overhanging load are detect­
ed late or not detected at all.
- When driving through curves
c::>page 87.
-With stationary objects c::> page 87.
A WARNING
-
Always pay attent ion to traffic when adap­
tive cruise control is switched on and the
pre sense front is active
c::> page 94. As
the driver, yo u are still responsible for
start ing and for mainta ining speed and
d istance to other objects. The pre sense
front is used to ass ist you. The dr iver must
a lways take action to avo id a collision . The
driver is always responsible for braking at
the correct time.
- I ncorrect use of the adaptive cruise con­
trol can cause collisions, other accidents
and serio us personal injury.
- For safety reasons, do not use adaptive cruise control when driving on roads with
many curves, when the road surface is in
poor condition and/or in bad weather
(such as ice, fog, gravel, heavy rain and
hydroplaning). Us ing the system unde r
these conditions could result in a coll i­
sion .
- Switch adaptive cruise control off tempo­ rarily when driving in tu rni ng lanes, o n
expressway ex its or in construction
zones. This prevents the vehicle from ac­
celerating to the set speed when in these
situations .
- The adaptive c ruise control system will
not brake by itself if you put your foot on
the accelerator pedal. Doing so can over-
ride the speed and distance reg ulation . ..,_

....,
N
0 > co
rl I.O
"' ....,
"' rl
Switching adaptiv e cruis e control off
• Push the lever away from you into position
@ until it clicks into p lace. The message
ACC: off appears.
The stored speed in the L ED line is erased .
@ Indicato r light s
Ill-adaptive cru ise control is switch ed on . No
objects ar e detected ahead. The stored spe ed
is maintained .
B-An object ahead was detected . The adap­
tive cruise contro l system regulates the speed
and d istance to the object ah ead and brakes/
accelerates automatica lly.
$ -adaptive cruise contro l is switched on . An
object ahead was detected. Yo ur vehicle re­
mains stopped and will not start driving auto­
matica lly.
• -The automatic braking is not eno ugh to
maintain a sufficient distance to an ob ject
ahead . Yo u must int ervene ¢
page 92 , R e­
quest for driver intervention.
© Instrument cluster display
If adaptive cruise cont ro l is not shown in the
instr ument cluster d isp lay, you can call it up
using the multifunction steering wheel b ut­
tons ¢
page 28 .
Based on the g raphics in the display, yo u can
determ ine if the system is maintaining a dis ­
tance to a vehicle ahead and what that dis­
tance to this vehicle is:
N o vehicle -No object ahead was detected .
White vehicl e -An object ahead was detected .
Red vehicle -Request for the driver to take ac­
tion ¢
page 92 .
Both arrows on the scale© in dicate the dis ­
tance to the object ahead. No arrow appears
when the vehicle is on an open road and there
is no object ahead.
If an object is detected
ahead, the arrow moves on the scale.
The green zone on the scale indicates the
store distance. Fo r information on changing
Audi ad apti ve crui se control 89
the distance, refer to r::!> page 91. If the dis ­
tance selected is exceeded or not reached, the
arrow moves into the red zone on the scale.
_& WARNING
- Using adaptive cru ise contro l incorrectly
can cause collisions, other acc idents and
ser ious inju ries .
- If you press t he
~IS-E T ~I button when driv­
ing at speeds below 20 mph (30 km/h),
the vehicle acce lerates automatically up
to 20 mph (30 km/h), wh ich is the mini­
m um speed that can be set.
(D Tips
- If you switch the ig nit ion or the adaptive
cruise cont ro l system off, the set speed
is e rased for safety reason .
- The Elect ronic Stabilization Control (ESC)
and Anti-Slip Regulat ion (ASR) both
switch on when the adaptiv e cruis e con­
tr ol is swi tched o n. ESC and AS R canno t
be switched off when ad aptive cruise
cont ro l is switched on .
- Wi th t he adap tive c ruise control activat­
ed the ESC sport mode cannot be ac tiv at ­
ed.
Changing the speed
Applies to vehicles: wit h Audi adaptive cru ise control
0
f
JJ
0
Fi g. 81 Operati ng leve r: c ha ngi ng the s pee d
• To increase o r reduce the speed in incre­
ments,
tap the lever up o r down .
• To increa se o r de crea se t he speed q uickl y,
hold the lever up or down until the red L ED
@ reaches the desired speed r::!> page 88,
rg. 80. ~