automatic transmission AUDI S3 SEDAN 2018 Owners Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2018, Model line: S3 SEDAN, Model: AUDI S3 SEDAN 2018Pages: 404, PDF Size: 62.3 MB
Page 80 of 404

Drivin g
for at idle fo r approximately two minutes
before shutting it off.
(D Tips
For up to 10 m inutes after stopp ing the en
gine, the rad iator fan may t urn on again auto
matically or it may continue to run (even if
the ignition is sw itched off) for the following
reasons:
- The coolant temperature is increasing due
to trapped heat.
- If the engine is warm and the engine com
partment also heats up from strong sun
li ght.
Messages
Engine runn ing. W arning! Turn off ignition be ·
fore le aving vehicl e
This m essage appears and a warning tone sounds
if you open the driver 's door when the engine is
running .
Press ing start /stop button again will swi tch off
engine.
This message appea rs when you press the
IS TAR T ENG IN E STOP I* button wh ile d riving
¢ page 77, Emergency off function.
Engine start system: malfunction! Ple ase con
tact S ervice
The engine automatic start system has a mal
function . Drive to an author ized Audi dealer or
author ized Audi Se rvice Facility immed iate ly to
have the ma lfunct ion co rrected. To sta rt the en
g ine , turn the key to pos it io n @ ¢
page 75 or
p ress and ho ld the
I S TART ENGINE ST OP ! button
until the engine is running .
DJ Key not r ecogniz ed . See own er' s manual
This message appears if there is no convenience
key inside the vehicle or if the system does not
recognize the key . T he conven ience key may not
be recognized, for examp le, if it is cove red by an
object that
disrupts the s ignal (s uch as a b rief
case), o r if the key ba tte ry is weak. Elect ronic de
vices s uch as cell phones can also interfere wit h
the signal.
78
To still be ab le to start or stop the engine, re fer
to
¢ page 79.
DJ Re mo te c ontro l ke y: hold back of ke y
again st the de signated ar ea . S ee owner 's man
ual
If the indicato r light turns on and this message
appea rs, there is a ma lfunction ¢
page 79.
Ill Key not in v ehicle?
Ill Remote control ke y: key not r ecogni zed. Is
t he key still in the vehicle ?
The Ill indicator light turns on and this message
app ears if the conv eni ence k ey was r emoved from
the veh icle when the engine was running.
If the
convenience key is no longer in the ve hicle, you
cannot sw itch the ignition on or start the eng ine
once you stop it . You also cannot lock the vehicle
from the outside .
Please press the bra ke pedal
This message appears if you do not step on the
brake peda l to start the engine on a vehicle with
an automat ic transmission.
Plea se select N or P
This message appears w hen start ing or stopping
t h e engine if t he se lecto r lever is not in t he "N " or
"P " pos ition. The eng ine will not sta rt/stop.
Turn off igniti on befor e le av ing vehicle . Batter y
i s di sc harging
This message appears and a warning tone sounds
i f you open the driver's door w hen the ign it ion is
switched on . Sw itch the ignit ion off so that the
vehicle battery will not discharge.
S hift to P , othe rwi se vehicle can roll aw ay.
Door s do not lo ck if l ever is not in P
This message appears for safety reasons if the
selector lever for the automa tic transmission is
not in the P position after the ignition is switched
off . Move the selector lever to the P posit ion .
Otherwise the ve hicle is not protected from roll
i ng and it cannot be locked .
Page 85 of 404

selector lever position is engaged. As soon as
you press the accelerator pedal, the parking brake releases automatically and your vehicle
starts to move
¢ page 83.
(D Tips
- Occasional noises when the parking brake is
set and re leased are normal and are not a
cause for concern.
- The parking brake goes through a self-test
cycle at regular intervals when the vehicle is
stopped. Any noises associated with this are normal.
- If there is a power failure, the parking brake will not set if it is released, and it will not
release if it is
set¢&. See an authorized
Audi dealer or authorized Audi Service Fa
cility for assistance .
Starting from a stop
Various convenience and safety functions may be
available when the vehicle begins driving, de
pending on vehicle equipment.
Starting on hills with the parking brake set
Requirement: the driver's door must be closed.
~ To start driving comfortably when on a hill, set
the parking brake and begin driving as usual.
The braking force of the parking brake does not release automatically until the wheels build up
enough driving force .
Starting on hills with hill hold assist
Hill hold assist makes it easier to start on hills.
Requirement: the driver's door must be closed
and the engine must be running.
~ To activate hill hold assist, press and hold the
brake pedal for several seconds. The vehicle
must be in an uphill direction of travel.
After releasing the brake pedal, the braking pow
er is maintained for a brief
moment ¢.&. to pre
vent the vehicle from rolling back when starting.
::li During this time, you can eas ily beg in to move .-<
~ your vehicle.
N .-< 0 N > 00
Driving
A WARNING ,-
Applies to: ve hicles with h ill ho ld assist
- If you do not begin driving immediately or
the engine stalls after releasing the brake
pedal, your veh icle may begin to roll back
ward. Press the brake pedal or set the park
ing brake immediately.
- The intelligent technology of hill hold assist
cannot overcome the limitations imposed by
natural physical laws. The increased comfort
offered by hill hold assist should not cause
you to take safety risks.
- Hill hold assist cannot hold the vehicle in
place on all hills (for example, if the ground
is slippery or icy).
- To reduce the risk of an accident, always
make sure the vehicle is situated safely
while stationary.
Automatic transmission
Introduction
Applies to: vehicles with automatic transmiss ions
T he automatic transmission is controlled elec
tronically . Upshifting and downshifting occur au
tomatically.
When a
moderate driving style is used, the
transm ission selects the most economica l dr iv ing
mode. The transmission upshifts at a lower RPM
and downshifts at a higher RPM to improve fuel
efficiency.
In the "S" selector lever position, the transm is
sion switches to a sporty mode after a kick-down
or when the driver uses a
sporty driving style
characterized by quick accelerator pedal move
ments, heavy acce leration, frequent changes in
speed and traveling at the maximum speed.
If desired, the driver can also select the gears
manually (tiptronic mode) ¢ page 88, Manual
shifting (tiptronic mode).
The S tronic is a dual-clutch transmission. Power
is transferred using two clutches that work inde
pendently from one another. They replace the
torque converter used in conventional automatic
.,.
83
Page 86 of 404

Driving
transmissions and a llow th e vehicle to a ccelerate
without a noticeab le interruption in traction .
Selector lever positions
Applies to: vehicles w ith automatic t ransmissions
F ig. 9 0 Instru ment cl uster : selector leve r po sit ions
•
F ig. 91 Selec tor lever lock
~ 0
0
> a, Ul
The se lected selector leve r pos ition is shown hear
the selector lever ¢
fig. 91 and in the instrument
cluster display ¢
fig. 90.
.,. Swi tch the ign ition on.
.,. In the "P/N " pos itio n, you mus t release t hese
lector lever lock ¢
page 84 .
.,. Move the selecto r lever into the desired posi
tion. The engaged selector lever pos ition is
shown in the shift gate .
Selector lever lock
The selector lever loc k prevents you from se lect
ing a gea r accidenta lly, causing the vehicle to
ro ll.
The se lector lever is locked in the "P" and " N"
po
sitions when the ignition is sw itched on. Yo u
must press the bra ke pedal to select another
po
sition. You must also press the interlock button if
you are moving from the "P" and "N" position.
84
The selector leve r lock on ly functions when the
vehicle is stationary or at speeds be low approxi
mately 1 mph (2 km/h) . At higher speeds, the
l ock is automatically deactivated in the "N" posi
tion.
The selector leve r is not locked when shiftin g
quick ly throug h "N ", for example from "R" to
"DI
S" . This makes it possible to free the veh icle
whe n it is stuck by "rock ing" it. The selector lever
l ock engages if the lever stays in the "N" position
l onger than approximately two seconds when the
brake peda l is not pressed .
Ignition key safety interlock*
Applies to: vehicles with ignition lock
You can only remove the key from t he ignit ion af
ter switching the ignition off if the selector lever
i s in the "P" pos it ion . T he selector lever will be
locked in t he "P" position as long as the key is not
i n the ig nitio n.
P - Park
This selector lever position prevents the vehicle
from ro lling. You ca n only shift into Park when
the veh icle is
stationary ¢,&. .
To sh ift in and out of the "P" se lector lever posi
tion, press the selector lever lock (button in the
selector lever handle)
and press t he brake pedal
at the same t ime .
The selector lever will be locked in the "P" posi
tion if there is a power fa i Lu re
¢ page 90, Se
lector lever emergency release.
R- Rever se
Only s hift into reverse gear when the ve hicle is
stationary and the engine is runn ing at id le
speed ¢.&. .
To se lect the "R" selec to r l ever positio n, press the
selector lever loc k
while pressing the brake ped
a l.
N - Neutral
The tran smission is in idle in th is posi tion .
D /S - Normal position for driving forward
In the "D/S " selector lever position, the transmis-
s ion can be operated e ithe r in the normal "D "
llll>
Page 88 of 404

Driving
- If the vehicle sti ll does not move in the de
sired direction, there is a system malfunc
tion. See an authorized Audi dealer or au
thori zed Audi Service Facility for assistance
to have the system checked.
(D Tips
Plug -in hybrid drive* : the transmission
switches automatically to the normal mode
" D" if the
l.,,f' I button ¢ page 98 is pressed
while i n sport mode "S" .
Driving tips
Applies to: ve hicles with a utomat ic transmissions
F ig . 9 2 Sect io n of the cente r co nso le: se le cto r lever w it h
i nte rlock butto n
Starting the engine
• Select the "P" or "N" selector lever position . At
low temperatu res (be low 14 °F ( -10 °C)), the
engine can only be started when t he se lec to r
l ever is in the "P " posit io n.
Starting from a stop
• Press and hold the brake pedal.
• Press and hold the interlock button in these
lector lever handle, se lect the des ired sele ctor
lever posit io n such as "D" ¢
page 84 and re
lease the loc k bu tton.
• Wait a moment unti l the transmission shifts.
Yo u w ill not ice a slight movement when the
gear engages.
• Release the brake pedal and press the accelera
tor
pedal ¢,&. .
Various convenience functions are avai lab le for
starting on hills ¢
page 83.
86
Stopping temporarily
• Keep the vehicle st ationary using the bra kin g
peda l, for examp le a t traffic ligh ts.
• Do not press the acce le rato r pedal when doing
this.
• To prevent the vehicle from rolling when you start driving, set the pa rking brake when stop
ping on steep
hills ¢.&. and ¢(Q).
• The parking brake will release a utomat ica lly
and the vehicle will start moving once yo u press
the acce le rato r pedal. Requirement: the d riv
er's doo r mus t be closed.
Stopping/parking
If the selector lever is not in the "P" pos ition
whe n you open the d river's door, the vehicle
could roll. In vehicles with a conven ience key *,
the message :
Shift to P, otherwise vehicle can
roll away. Door s do not lock if lever is not in P
appe ars . A wa rning tone wi ll also sound.
• Press and hold the brake peda l¢ ,&. .
• Set t he par king brake.
• Select the "P" se lector lever posi tion .
Un der certai n circumstances, (such as dr iving in
the mo unta ins or towi ng a trailer), it may be use
ful to switch temporar ily to the m an ual shift pro
gr am in or der to ad ju st t he gears to the driv ing
cond it ions by hand ¢
page 88.
When parking on a level surface, s imp ly place the
se le ct or lever i n the "P" pos ition. On inclines, a c
tivate the par king b rake first and then move the
se lector lever to the "P " posit ion ¢
page 81. Thi s
prevents the locking mechanism from being
l oaded too heavily and will make it easier to
move the selector lever out of the "P" position.
A WARNING
- The vehicle can roll even whe n the engi ne is
sw itched off .
- Unintended vehicle movement can lead to
serio us injuries.
- Never leave your veh icle with the engine
r u nning while in gear. If you must leave
your veh icle when the eng ine is r unning, set
t he par king brake and move the se lecto r lev
er to the "P " posi tion .
Page 89 of 404

u. 00 .-< N l' N .-< 0 N > 00
-Power is still transferred to the wheels
when the engine is running at idle. To pre
vent the vehicle from "creeping", you must keep your foot on the brake when the en
gine is running and the selector lever is in
the "D", "S" or "R" position or "tiptronic"
mode is selected.
- Do not inadvertently press the accelerator
peda l when the vehicle is stopped if a gear is
engaged. Otherwise the risk of an accident
increases because the vehicle will start to
move immediately, even if the parking brake
is set.
- To reduce the risk of an accident, do not
press the acce lerator pedal when changing
the selector lever position while the vehicle is stationary and the engine is running.
- Never engage the "R" or "P" selector leve l
positions while driving. It could cause a
crash.
- Before driving down a steep slope, reduce
your speed and shift into a lower gear with
"ti ptron i c".
- Do not ride the brakes or press the brake
pedal too often or too long when driving
downhill. Constant braking causes the
brakes to overheat and substantially re
duces braking performance, increases brak
ing distance or causes complete failure of
the brake system.
- If you must stop on an incline, always hold
the vehicle in p lace with the foot brake or
park ing brake to prevent it from rolling
back.
- Never hold the veh icle on an incline with a
sl ip ping clutch. The clutch opens automati
cally when it becomes too hot from the
overload. The
ml indicator light turns on
and a message appears
¢ page 89 when
the clutch is over loaded .
{LlJ) Note
- When stopping on an incline, do not try to
ho ld the vehicle in place by pressing the ac
ce lerator pedal while a driving gear is se
l ected. This can cause the automatic trans
mission to overheat and can damage it. Set
Driving
the parking brake or press the brake pedal
to prevent the vehicle from rolling.
- Allowing the vehicle to roll when the engine
is stopped while the selector lever is in the
"N" position will damage the automatic
transmission, because it is not lubricated
under those circumstances
¢ page 3 78,
Towing with a tow truck.
- The transmission can overheat and be dam
aged under certain driving and traffic condi
tions such as frequent starts, creeping for a
long time, or stop-and-go traffic. When the
ml or. indicator light turns on, stop the
vehicle at the next opportunity and let the
transmission cool¢
page 89.
(D Tips
For safety reasons, the park ing brake only re
l eases automatically when the driver's door is
closed.
Hill descent control
App lies to : vehicles wi th automatic transmiss ions
The hill descent control system assists the driver
when driving down hills.
Hill descent control is act ivated when the selec
tor lever is in the "D" or "S" posit ion and you
press the b rake pedal. The transmission auto
matically se lects a gear that is suitab le for the
hill. Hill descent contro l tries to ma inta in the
speed achieved at the time of braking, within
physical and technica l limitations. If may still be
necessary to adjust the speed with the brakes.
Because hill descent control cannot shift down
farther than 3rd gear, it may be necessary to
shift into tiptronic mode in very steep areas . In
th is case, shift into 2nd or 1st gear in t iptronic
mode to use the engine's braking force to rel ieve
the brakes.
Hill descent control switches
off once the hill lev
els out or you press the accelerator pedal.
On vehicles with a cruise control system*
¢ page 120, hill descent control is also activated
when the speed is set .
.,,.
87
Page 90 of 404

Driving
& WARNING
Hill descent control cannot overcome phys ical
limitations, so it may not be able to maintain
a constant speed under all condit ions. Always
be ready to apply the brakes .
Manual shifting (tiptronic mode)
Applies to: vehicles with automatic transmissions
The tiptronic mode allows the driver to shift the
gears manually.
F ig. 9 3 Center conso le : shifting manually w ith the se lector
l ever
F ig . 94 Steering wheel: shifting manual ly w it h the s hift
paddles*
Shifting with the selector lever
You can sh ift into tiptro nic mode while stationary
a nd while driv ing.
• To s hift into tiptronic mode, p ush the selector
lever from the "D/S" position to the right in the
t ip tr onic sh ift gate . Once the transmission has
swi tched modes, t he se lec tor lever posi tion
M
is shown in the instrumen t clus ter display
¢ page 84, fig. 90. For example, M4 means the
fo urth gear is engaged.
• To shift up a gear, tap the se lector lever for
ward
0 ¢ fig. 93 .
88
• To shift down a gear, tap the selecto r lever
backward
0 -
Shifting with the shift paddles*
You can operate the s hift paddles in the "D/S" or
" M " (tiptro nic shift ga te) se lec tor lever posi tions.
• To shift up one gear, tap the shift paddle 0
¢fig . 94.
• To shift down a gear, tap the 0 shift paddle.
• Applies to: RS models: to select the lowest/
highest possi ble gear, press and hold the sh if t
paddle
0 10 .
If the shift paddles a re tapped wh ile in the "D/S"
selector lever position, a utomat ic mode sw itches
off briefly . To swit ch from manually shift ing bac k
to automatic shifting immediate ly, tap t he shift
padd le
0 ¢ fig . 94 for 1 second .
To keep sh ift ing using the shift padd les, move
the selec to r l ever to the right o ut o f th e "D/S" po
sition into the tiptronic shift gate .
The tra nsmission a utomatically sh ifts up or dow n
before cr itical engine speed is reac hed.
Applies to: RS models: when accelerating, the
transm iss ion does
not au tomatically shift to the
next gear short ly before the maxim um permitted
engine RP M is re ached. Shift to the next highest
gear at the right time.
The tra nsmission on ly allows manual shifting
whe n the engine speed is w ith in the perm itted
r a nge.
Kick-down
Applies to: vehicles with automatic transmissions
Kick-down enables maximum acceleration.
When you p ress the accelerator pedal down be
yo nd the res istance point (called kick-down), the
automat ic transmission downshifts into a lower
gear, depending on vehicle s peed and engine
RPM .
It shifts up into the next higher gear once
t h e maximum specified engine RPM is reached .
Applies to: RS models: in tipt ronic mode, the
transm iss ion does
not automa tic ally shift down
i nto a lower ge ar. If yo u m ust accelera te, for ex
ample to pass a vehi cle, you mus t sh ift manually .
..,.
Page 91 of 404

u. co ... N l' N
A WARNING
Please note that the wheels could spin on
slick or slippery roads when kick-down is ac
tive .
Launch control program
App lies to: ve hicles with S tro nic tra nsm issio n an d La unch
Co ntrol P rogram
-
The launch control program provides the best
possible acceleration when starting from a stop .
Requirement: the eng ine must be at operating
temperature and t he steer ing whee l must not be
turned.
.,. Deact ivate l) the S tart/Stop system*
~ page 81. The L ED in the ~ button turns on .
.,. Wi th the engine runn ing, p ress the I.!, O FF ! but
ton briefly one time . The
11 indicator light
turns on and the message
Stabili zation control
( ESC ): s port. W arning! Rest ricted st a bilit y
ap
pears in the instrument cluster display.
.,. Pull the selector lever back out of the "D/S" po
s it ion br iefly to select the S pos it ion, or press it
toward the right into the t iptronic pos ition or
select the
Dynamic d riving mode in d rive se
lect* ~ page 140.
.,. Press t he b rake peda l firmly with you r left foot
and hold it all the way down for at least one
second .
.,. At the same time, press the gas pedal a ll the
way down with your right foot unt il the engine
reaches and stays at a high RPM level.
.,. Remove your left foot from the brake pedal
within five
seconds ~,&. .
A WARNING
-Always adapt yo ur driv ing to the traffic flow.
- Only use Launch Control when road and traf-
fic cond itions allow it and other dr ivers will
not be endangered or impacted by you r driv
ing and the vehicle 's accele ration.
- Please note tha t the drive whee ls can sp in
and the vehicle can break away when sport
8 l ) It is n ot poss ib le to deac tiv ate t he system wit h all ve rs io n s N &j of th e tran sm iss ion.
Driving
mode is switched on, especially when the
road is slippery.
- Once the vehicle has started moving, press
the !.!> OFF I button briefly to turn the sport
mode off.
(D Tips
- The transmission temperat ure may increase
significant ly after using the launch control
program. If that happens, the program may
not be ava ilable for a few minutes. It will be
availab le aga in after a cool-down period.
- When accelerating using the launch contro l
program, all vehicle parts are subject to
heavy loads . This can lead to increased
wear .
Transmission malfunction
Applies to: vehicles wit h automatic transmissions
• Transmis sion : malfunction! Pl eas e s top ve
hicle and shift to P
There is a malfunction in the transmission . Park
the vehicle securely and do not cont inue driv ing .
See an author ized Audi dealer or author ized Audi
Se rvice Facility for assistance .
• Transmission o verhe ating! Plea se stop th e
vehicle!
The transmission is too hot and can become dam
aged. Stop and let the transmiss ion cool w ith the
engine running (at idle) i n the "P" selector lever
pos ition . T hen the ind icator light and the mes
sage turn off, d rive to an authorized Aud i dealer
o r auth o rized Aud i Serv ice Facility immediately to
have t he malfunct ion cor rected . If the indicato r
light and the driver message do not turn off, do
not continue driving . See an authorized Audi
dealer or authorized Audi Service Facility for as
s istance.
[O] Tran smission: malfunction! You can contin-
u e dri ving. See owne r's manual
.,.
89
Page 92 of 404

Driving
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunct ion corrected .
[i1 Transmission: malfunction! You can contin
ue driving with limited function. No reverse
gear
There is a system malfunction in the transm is
sion. The transmission is switching to emergency
mode. This mode only shifts into certain gears or
will no longer shift at all. The engine may stall.
You cannot engage the reverse gear. Drive to an
authorized Audi dealer or author ized Audi Service
Facility immediately to have the malfunction cor
rected .
[i1 Transmission: malfunction! You can contin
ue driving in
D until engine is off
Drive the vehicle away from movi ng traffic and
park. See an authorized Audi dealer or authorized
Aud i Serv ice Facility for assistance.
[i1 Transmission: too hot . Please adapt driving
style
The transmission tempe rature has increased s ig
n ificant ly. Dr ive very cautiously or take a break
from driving unt il the temperature returns to the
normal range and the indicator light turns off.
[O] Transmis sion: please press brake pedal and
select gear again
If the transmission malfu nctions because the
temperature is too high, a message appears
when the transmission is cooled .
90
Selector lever emergency release
Applies to : vehicles wi th automatic transmissions
If the vehicle's power supply fails, the selector
lever can be released in an emergency .
Fig. 95 Selector leve r: remov ing the shifter boot
Fig. 96 Selector lever: using the emergency release to
move out of the Pa rk posit ion
To maneuver or tow the vehicle, the emergency
release must be used to move the selector lever
from the P position .
The emergency release mechanism is located in
the right area under the selector lever shift gate .
Using the emergency release can be complicated .
We recommend contacting an authorized Audi
dealer or authorized Aud i Service Facility for as
s is tance, if necessary.
The screwdr iver from the vehicle tool kit located
i n the luggage compartment is needed to for the
emergency re lease
c::> page 360 . Use the flat side
of the reversible screwdriver blade.
Removing the shifter boot
.,. Set the park ing brake(®) ¢.& to secure your
veh icle from rolling. If this is not possible, se
cure your vehicle from rolling using another
method .
.,. Switch the ignit ion off.
Page 96 of 404

e-tron
for the high voltage battery can lead to seri
ous damage and/or a decrease of the capacity
void coverage under the New Vehicle Limited
Warranty.
Starting/driving the vehicle
A pp lies to: ve hicles w ith plug- in hybrid drive
The vehicle is started and stopped with the
IS TAR T ENGINE STOP I button . Please also read
the information under
Q page 76, Starting the
engine.
Establishing drive ready mode
See Q .& in Introduction on page 92.
Requirement: a charging cable must not be con
nected to the vehicle
Qpage 115 and the selec
tor lever must be in the "P" or
"N" position.
- Press the brake peda l.
- Press th e
I START ENGINE STOPI button .
When the veh icle enters drive ready mode, the
status message
e-tron READY appears briefly in
the instrument cluster display and the needle in
the powe r meter points to
READY Q page 95.
Driving
The vehicle starts with the electr ic motor after
establishing the dr ive ready mode and if the con
ditions for electric drive mode have been met
Qpage98.
The cond itions to drive are essentially the same
as for the automat ic transmission
Q page 83 .
You and your passengers should anticipate the
possibility of a sporty acceleration.
Ending drive ready mode
- Place the selector lever in the P position.
- Switch the ign ition off with the
I START ENGINE STOP ! button.
Vehicle sound1>
The vehicle generates an electronic engine sound
so that you r vehicle can be heard from the out
side when in electr ic drive mode. The veh icle
l) Not available in all markets.
94
sound automatically fades out at higher speeds
when the sounds from the tires and wind start in
creasing .
Switching the ignition on/off
You can switch the ignition on without establish
in g drive ready mode.
- To switch the ign ition on or off, press the
!START ENGINE STOPI button. Do not press the
brake pedal while do ing this.
When the ignition is switched on, the needle
stays pointed at
OFF CD Q page 95, fig. 98 or
OFF is displayed CD~ page 95, fig. 98.
No indicator lights stay turned on when the igni
tion is switched off.
Ignition is switched off automatically
To prevent the vehicle battery from draining, the
i gnition will switch off automatically under the
follow ing cond it ions:
- The vehicle has already been driven.
- The vehicle is stationary.
- The gasoline engine is not runn ing.
- The driver's door is opened.
- The driver's safety belt is unbuckled .
- The brake pedal is not pressed.
In this case, the activated low beam is replaced
by the parking light. The message
Side marker
lights will switch off automatically in 30 mi
nutes. See owner 's manual
appears in the instru
ment cluster display . The parking lights will
switch off after approximately 30 minutes or
when you lock the veh icle.
If the gasoline engine was not stopped, the mo
tor continues running and the ignition does not
automat ically switch off
Q & .
A WARNING
To reduce the risk of poisoning, never allow
the engine to run in confined spaces .
-
Page 100 of 404

e-tr on
~ To switch between the short -term and long
term memory, turn the left thumbwhee l on the
multifunction steering whee l.
Setting plug-in hybrid drive modes
Applies to: vehicles with plug-in hybrid drive
You con select between one electric mode and
two hybrid modes .
Fig . 1 01 Center console: but ton c:=!i'
~ Press the 14• 1 button repeatedly until the de
s ired dr ive mode is d isplayed in the instrument
cluster/Infota inment system display .
You can change modes when the vehicle is sta
tionary or while driving . If the veh icle operat ing
conditions will not allow you to set the mode
manually , the last act ive mode is se lected.
The active mode is displayed the first t ime the
14' 1
button is pressed .
,cf,V e-tron mod e: E V -EV mode is electric driv ing
only . EV mode is active at the beginning of every
tr ip depend ing on the operating condition of the
veh icle . T he LED in the
14"1 button turns on .
The. indicator light also appea rs in the instru
ment cluste r. T he gasoline eng ine rema ins
t urned off, as long as the cond it io n s for electr ic
driving are
met ¢ page 98, Conditions for elec
tric driving.
~ e- tron m ode : H ybrid -the electr ic motor and
t he gasoline engine wo rk efficien tly toge ther in
hybrid mode . The high -vo ltage battery will be
used to the fullest extent when t his mode is
switched on. This mode is best suited for long
d istances .
.. ~ e -t ro n mode: Batt ery Hold -the electric mo
tor and the gasoline engine work together in Bat -
98
tery Hold mode, so that the high -voltage battery
charge level is maintained as much as possib le .
(D Tips
- Applies to: Battery Hold mode: th e h igh
vo ltage battery charge level can sti ll de
crease depending on the driving behavior.
- If you select the sport driving mode "S"
when in EV mode, the Battery Ho ld mode is
automatically selected.
- If the
14"1 ¢ page 98 button is pressed w hile
in sport driving mode "S", the transmission
switches automatica lly to normal mode "D".
- When temperatures are below approxi
mate ly
14 °F ( -10 °C), the vehicle heat out
put in EV mode is reduced in order to attain
higher ranges. If the windows fog up or a
hig her heat output is desired, switch on the
Hybrid or Battery Hold mode .
Conditions for electric driving
Applies to: vehicles with plug-in hybrid drive
The EV mode ca n only be switched o n if the fol
l ow ing condit ions are met:
- The charge level of the high-voltage battery
must be sufficient .
- The temperature of the high-voltage battery
must be adequate (outside temperatures not
below approx imately
14°F / -10°( and not
above
1 04°F / 40°C)
- The speed must not be h igher than approxi -
mate ly
80 mph (130 km/h) .
- Kick -down must not be activated .
- The sport drive mode "S " must not be selected .
EV mode is switched off if one or more of the
conditions are not met. The gasoline engine wi ll
start automatically. The
l!'§'J indi cator light turns
on as a message in the instrument cluster. The
LED in the
14" 1 butto n and the . indicator light
turn off .
E lectric drive mode will not contin ue automati -
cally. React ivate the EV
mode ¢ page 98. Ill-