infotainment AUDI S4 2015 Owners Manual

"' N
0 :,,: co ,...., \!) ..,.,
,...., ..,., ,....,
¢fig. 10. The data from the single-trip mem ­
ory (memory leve l 1) is being displayed if a
D
appears in the display. If a fJ is shown, then
the data from the total-trip memory is being
d isplayed (memory level
2). The fuel pump
nozzle
ii indicate s the efficiency program*
¢page 26 .
Single-trip memory (Trip computer 1)
The single -trip memory stores the trip infor­
mat ion from the time the ignition is turned on
until it is turned off. If the trip is continued
within 2 hours from the time the ignition was
turned off, the new data will be included in
the calculation of the current trip informa­
tion. If the trip is interrupted for
more than 2
hours the memory is reset automatically.
Total-trip memory (Trip computer 2)
Unlike the sing le-trip memory, the total-trip
memory is not reset automatically. This per­
mits you to evaluate your driving data for the
enti re pe riod between manual resets.
Efficiency program*
The effic iency program can help you to use
less fuel ¢
page 26.
Operation
Applies to vehicles: with trip computer
The trip computer is controlled by two
switches on the windshield wiper lever.
Fig. 11 Wind shi eld w iper lever: controls for the t rip
comp uter
Operating
~ To display the trip computer memory leve ls,
press the
I RESE T I button @¢ fig. 11 re-
Driver information display 25
peated ly until the desi red memory level is
show n in the display.
~ To display trip informat ion with in a memory
level, press the top or bottom part of the
function selection switch @.
The trip computer will not operate un less the
ignition is on. When you turn on the ign it ion,
the function that was in use when you last
turned the ignition off will be displayed .
In addition to information about the trip com­
puter (trip computer 1, 2 and the efficiency
program*), information about other systems
can also be shown in the disp lay. To switch the
display between the different information ,
tap the
! RESET I button @briefly.
Resetting values to zero
~ Select a value in the desired tr ip computer
or in the eff iciency program".
~ Press and hold the I RESE T I button @for at
least one second . All values in the selected
trip computer or in the efficiency program*
are reset to zero.
If the data in trip computer
1 are deleted ,
then the values in the efficiency program* w ill
also be reset.
With some vehicle equipment levels, the val­
ues for the single trip or total trip memory
can a lso be reset in the Infotainment system
¢page 25 .
(D Tips
All stored va lues w ill be lost if the vehicle
battery is disconnected.
Basic Settings for the trip computer
App lies to vehicles : wit h trip co mputer
The radio or MM!* operating unit is used for
setting the trip computer's basic settings.
~ Select: Function button !CAR !> Instrument
cluster > On-board computer 1
or On-board
computer 2 . .,.

46 Opening and clo sing
Operation
App lies to vehicles: wit h garage door opene r (H omelink)
,,,,, r ,O :O·,) 11111
®
Fig. 41 Headl iner: co ntro l un it
Requirement : The buttons in the roof headlin­
er must be programmed ¢
page 46 or
¢
page 4 7 and the vehicle must be within
range of the system, such as the garage door
opener .
.. Press the button to open the gar age door.
The LED@ blinks or turns on .
.. Press the button again to close the garage
doo r.
@ Tips
To open or close the garage door, press the
button, but do not hold it for longer than 10 seconds or the ga rage doo r opener
mod ule will switch to programm ing mode .
Programming the buttons (version A)
Applies to vehicles : wit h garage door opene r (Homelink)
You can p rog ram both fixed code and rolling
code systems using this procedure .
Programming or reprogramming buttons
.. Switch the ign ition on .
.,. Press and ho ld the button in the roof head­
li ner ¢
page 46, fig. 41 that you would like
to program for at least 10 seconds. Or
.. Se lect : ICAR lf u nction button>
C a r sys tem s*
control button > Vehicle sett ing s > Garage
door op ene r> Program garage door open ­
er .
If this path is not ava ilable, program the
button as described in version
B ¢ page 47 .
.. Follow the instructions in the MMI.
Erasing button programm ing
T he programmed b uttons cannot be erased
individua lly. They must a ll be erased together .
Reprogram the buttons if necessary.
.,. Select: !CARI function button>
Car sy ste m s*
contro l button > Vehicle settin gs > Garag e
d oo r opener > Clear pr ogram setting s
>
Yes.
Displaying the vers ion /status /country
code
.. Select : !C A RI function button > Ca r syste ms *
cont ro l button > Vehicle setting s > Garage
door opener > Version information .
{!) Tips
-Programming through the MMI* is not
possible with all infotainment systems .
If this is the case , program the buttons
as described in version B ¢
page 47 .
- The required distance betwee n the hand
transmitter and the Homelink module in
the radiator gri lle ¢
page 47, fig. 42
depends on the system that you are pro­
gramming .
- Depe nding on the model of the system,
you may need to release the button o n
the remote control du ring p rog ramming
and press it again . Hold each position
you try fo r at least 15 seconds befo re
t ry ing another p ositi on. Keep the turn
signa ls on your ve hicle in view when do­
ing this .
- Aft er p rog ramm ing the garage door
opener, it may be necessary to synchron ­
ize the motor with the system. Refer to
the manufacturer's instructions .