AUDI S4 2016 Owner's Manual

..... N
0 ::..:: co ..... ..... /(@) Anti-lock braking system (ABS)
This
warning/i ndicator light monitors the ABS
and the electronic differential lock (EDL) .
The warning/indicator light fIE) (USA models)/
ti] (Canada models) wi ll come on for a few sec­
onds when the ig nition is switched on. The ligh t
w ill go out after an au tomatic check sequence is
comp leted.
There is a malfunction in the ABS when :
-The warning/indicator lig ht does not ill uminate
when you switch the ig nition on .
- The warning/indicator light does not go out af­
ter a few seconds.
- The warning/indicator lig ht ill uminates wh ile
driv ing .
The ESC indicator light a lso ill uminates if the re is
a ma lf u nction in the ABS. The message
Stabiliza­
tion control (ESC ): Fault! See owner's manual
als o appears in the inst rument cluste r display
and a warn ing tone sounds.
The brake system will still respond even with­
out the assistance of the ABS system. See your
authorized Audi dealer as soon as possible to re ­
store full braking performance.
For mo re infor­
mat io n regarding the ABS
c::> pag e 177.
M alfunction in the brake system
If the b rake warning light c::> page 15 and the ABS
warn ing illuminate
together there may be a ma l­
function in the ABS , and there may also be a ma l­
function in the b rake system itse lf
c::> .&. . The ABS
will not work and you will notice a change in braking respon se and performance.
In the event of a malfunction in the brake sys ­
tem
the warn ing/ indicator light 1111 (USA mod­
e ls)/ . (Canada models) in the instrument clus­
ter f lashes
r:::;, page 15 .
Malfunction in the electronic differential
lock (EDL)
The EDL works toget he r with the ABS . The ABS
war ning light w ill come on if there is a ma lf u nc­
tion in the ED L sys tem
c::> page 1 77. See your au ­
t h oriz ed A udi de aler as soon as poss ib le .
Instruments and ind icator lights
A WARNING
- If the fIE) (USA mode ls)/ tl] (Canada mod­
els) warning light does not go out, or if it
comes on while dr iv ing, the A BS system is
not working prop erly. The veh icle can t hen
be s toppe d only wi th the s ta nd ard brake s
(wit hou t A BS). Y ou will no t have the pro te c­
t ion A BS provi des . Cont act your aut hor ized
Au di deale r as soon as possible.
- US A mode ls: I f th e 1111 warning light and
the
9 warn ing ligh t come on togethe r, the
rear w heels could lock up fi rst under hard
braking . Rear wheel lock- up can cause loss
of vehicle contro l and an acc ident. Have yo ur
veh icle repaired immediately by your au ­
thorized A udi dealer or qualified workshop .
Drive s low ly an d avoid sudd en, hard brak e
ap pli catio ns.
- Canada models : If the brake warn ing light
• and t he A BS warning ligh t
tlJ come on
toge ther, th e re a r wh ee ls cou ld loc k up first
un der hard b raking. Rea r whee l lo ck- up can
c a use l oss of ve hicle con trol and a n acci­
dent . Have your ve hicl e repaired immedia te­
ly by your a uthorized Audi dea ler or q uali­
fied workshop. D rive slowly and avoi d sud­
den, ha rd brake applications.
tli I !i: Safety systems
The fl (USA models)/ EI (Canada mode ls) indi­
cator lig ht monitors the safety systems (e.g. a ir ­
bags, pretens ione rs) and illum inates fo r a few
seco nds each time you swi tch the ignition on.
If the
II (USA models) tEI (Canada models) in­
dicator light does not go out, o r if it ill uminates
wh ile you a re dr iv ing, or if it sta rts to b link, t hen
t h ere is a malfunct io n somewhere in the system .
If the ligh t does not illum inate wh en yo u sw itc h
t h e igni tion o n, t his a lso means there is a mal­
funct ion.
A WARNING ~
If yo u have a ma lf u nct ion in the safe ty sys-
tems, contact your authorize d Au di d ealer im ­
mediately. Ot herwise the safety systems may
not wor k properly in an accident .
19

Instruments and indicator lights
(0) Worn brake pads
EiJ Brake pads!
If the warn ing light illum inates, immed iate ly
contact your authorized A ud i dealer o r qualified
wo rkshop to have all brake pads inspected. O n
USA models the wa rni ng lig ht
EiJ comes on to ­
gethe r wi th the war ning l igh t
1111 . Both sets of
b rake pads on an ax le m ust always be rep lace d at
the same time .
A WARNING
Driv ing with bad bra kes can ca use a co llision
and ser ious personal in jury.
- If the wa rning light
EiJ and the warning
light
11111 ) w ith the message Brake pads !
comes on in the instrument cl uster display,
i mmediately contact your author ized Audi
dealer or qualified workshop to have all
bra ke pads checked o r rep laced if necessary.
EPC Electronic power control
This warning/indicator light monitors the elec­
tronic power control .
-
The~ warni ng/indicator light (Electronic Powe r
Control) ill uminates when you switch the ign ition
on as a function check.
(D} Tips
If this wa rning/in dicator light ill uminates
wh ile you are driving, then there is a mal func­
tion in the eng ine electron ics. Have the ma l­
function corrected as soon as possib le by yo ur
author ized A udi dealer or a qualified repair fa­
cility .
0 Malfunction Indicator Lamp (MIL)
The Malfunc tion Ind ica tor Lam p (M IL) is part of
the On-Boa rd Di ag nosti c (O BD II) system. The
symbo l
('4 lights up whe n the ignition is swi tch ­
e d on and wi ll turn off after the engine has sta rt·
e d and has sett led at a constant idle speed . This
i n dicates that the MIL is working p roperly.
l ) - : USA mode ls o nly
20
The wa rning lig ht ill uminates w hen the re is a
malfunction in the engine electronic system.
Contact yo ur aut ho rized Aud i dea le r and have the
malfunction corrected.
An impro per ly closed fue l filler cap may also
ca use the MIL light to illuminate ¢
page 200 .
For more info rm ation c::> page 29 .
!?) Engine speed limitation
App lies to vehicles : wi th engine speed limitatio n
lfl Do not exceed max. engine speed of XXXX
rpm
The lfl symbo l illu min ates when the re is an en­
gine co ntro l ma lf u nct ion. The~ indica tor ligh t
in the instrument clus ter also illum ina tes . T he
engine spee d is limited to the s peed displayed in
the d river info rmation system. Keep in mind t hat
the engine speed w ill not exceed the value dis ­
played in the driver information system, for ex­
amp le w hen downshifting.
D rive to your authorized A udi dealer immediate ly
to have the mal function cor rected .
~~. Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your author ­
i zed Audi dealer and have the oil sensor inspect­
ed. Until yo u have this done, chec k the oi l level
each time you refuel just to be on the safe side
¢ page 207.
Bu Tank system
Ii] Please refuel
If the indicato r light turns on for the first time
and t he message appea rs, the re are about
2.1- 2.4 gallons (7 • 9 lite rs) of fuel left in the
ta nk. Time to refuel¢
page 200 .
Ii] Fuel tank system malfunct ion! Contact deal -
er ..,.

..... N
0 ::..:: co ..... ..... If the indicator light turns on and this message
appears, there is a malfunction in the tank sys­
tem.
Drive to your authorized Audi dealer immediately
to have the malfunction corrected.
Ci:> Windshield washer flu id level
ra, Please refill washer fluid
If the symbol illuminates, add windshield washer
fluid to the washer system and also to the head­
light washer system*
I:!) page 216.
~ Windshield wipers
El Windshield wiper defective
There is a malfunction with the windshield wip­
ers.
Drive to your authorized Audi dealer immediately
to have the malfunction corrected.
~/ }D 10$ Defective light bulb warning
If the r.:I indicator light turns on, a bulb has
failed. The message indicates the location of the
bulb.
- If the Im indicator light also turns on, then a
fog light has failed. The position of the indica­
tor light corresponds with the location on the
v eh icl e.
- If the II indicator light also turns on, then a
rear fog* light has failed. The position of the in­
dicator light corresponds with the location on
th e vehicle.
This warning can also occur if the light switch is
in an unengaged position between two symbols.
Vehicle lights: System fault!
If the me ssage appears, there is a malfunction in
the headlights or light switch .
Drive to your authori zed Audi dealer immediately
to have the malfunction cor rected.
Instruments and indicator lights
A WARNING
- Light bulbs are pressurized and could ex­
plode while they are being changed causing
serious personal injury .
-
-Work with due care when handling the high­
voltage section of gas discharge (xenon)
lights* . Failure to do so could result in death
or serious injury.
@ Tips
Have the bulb replaced or the connection re­
paired by your authorized Audi Service depart ­
ment.
i,0 Headlight range control
Applies to vehicles: with headlight range control
B Headlight range control defective !
If the symbol B illuminates, the dynamic head­
light range control is no longer working properly .
Have the system checked and repaired at your au­
thorized Audi dealer.
§0 Adaptive Light
Applies to vehicles: with adaptive light
r!J Audi adaptive light: defective
If the indicator light turns on and this message
appears , there is a malfunction in the adaptive
light system. The headlights still function.
Go to an authorized dealership to have the head ­
lights or the control unit for the adaptive light re­
paired.
@. o Light/rain sensor
Applies to vehicles: with light/rain sensor
II Automatic headlights/ automatic wipers
defective
If the indicator light turns on and this message
appears , the light/rain sensor is not functioning
correctly.
For safety reasons the low beams are turned on
permanently with the switch in
AUTO. However, .,.
21

Instruments and indicator lights
you can continue to turn the lights on and off us ­
ing the light switch . You can still control a ll func­
tions that are independent of the rain sensor
through the w indshield wiper lever.
Contact your author ized Audi dealer as soon as
possible to have the problem corrected.
; Adaptive dampers
Applies to vehicles: with Audi drive select and adaptive damp­
ers
B Su spen sion : S yst em fault!
If the B symbol in the display comes on, there is
a ma lf u nction in the adaptive dampers . P lease go
to an author ized Audi de aler or qu alified work­
shop to have the ma lfunction repaired .
!-: Sport differential
Applies to vehicles: with Audi drive select and sport differen ­
tial
Sport differ ential: Syst em fault!
There is a malfunction with the sport differential.
Drive to your authorized Aud i dea ler immediately
to have the malfunct ion corrected.
Sport differential: Overhe ating
The transmission tempe rature has increased s ig­
n ificant ly due to the sporty driv ing manne r. D rive
i n a less sporty manner until the temperature re­
turns to the normal range and the indicator light
switches of.
A WARNING
Contact your authorized A udi dealer or quali­
fied workshop if the sport differential is faulty
or ma lfunctioning. The repa ir must be per­
formed by trained personnel us ing the correct
oil in order to ensure safety .
~ Ignition lock
II Ignition lock defective
There is a malfunction in the electronic ignition
lock . Please go to an authorized Audi dea ler or
other qualified workshop to have the malfu nction
repaired .
22 ¢
Q Turn
signals
Wheneve r yo u use the left B or the right Ill
turn s ignal , the ind ic a tor light blinks. When you
u se the emergency flashe rs, both indicator ligh ts
f lash.
If one of the tu rn signa l ligh t bulbs bu rn out, the
turn s ignal will b link t wice as fast as no rmal.
Caref ully drive to yo ur a uth o rized Aud i dea ler im­
mediate ly to have the malfunction corrected.

,....,
N
0
""' CX) ,....,
I.Cl U"I ,....,
I.Cl ,....,
Driver information
system
Introduction
The Driver information display inside the instru­
ment cluster provides you, the driver, with im­
portant information.
Fig. 7 Instrument cluster: ce nter display
Fig. 8 Wipe r lever: contro ls for the menu display
Center display
With the ignition on, the display in th e Driver In­
formation System shows the following informa­
tion :
- CD* inserted or Radio* station set
- Outs ide temperature*: At temperatures below
41 °f (+S
0
(), a snowflake symbol appears in
front of the temperature display¢ ,1,. .
- Warning if one of the doors, front lid or engine
compartment lid is not closed.
Additional functions
You can open the following functions in the Driv­
er Information System display by pressing the
I RESETI button¢ fig. 8 one or more t imes :
Digital speedometer*
Tire pressure monitoring*
¢pag e235
Driver in forma tion system
Trip computer* ¢page24
Efficiency program* ¢page26
Service interval display ¢page28
Speed warning ¢page Bl
Gearshift selector posit ions Au -i=>page 91
tomatic transm ission
Adaptive cruise control*
¢ page 98
Auto Check Control
Some functions and vehicle components are
scanned for their operating status when you
switch the ignition on and while you are driving. Malfunctions or required service procedures are
signaled audibly and indicated by red and yellow
illum inated symbols and reminders in the dis­
play.
A WARNING
--
- Never rely exclus ively on the outside tem­
pe rature display to determine if a road sur­
face is icy or not. Keep in m ind that road
surfaces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperat ure above 41 °f (+S °C).
- Always remember, even if the "snowflake"
symbol (ice warning) does not appear in the
display, black ice could be on the road.
- Always reduce your speed and dr ive with
specia l care in cold weather conditions when
the chance of encountering icy road surfaces
increases.
(j) Tips
If the vehicle is stationary, or if you are driv­
ing at a very low speed, the temperature
shown in the disp lay might be slightly higher
than the actual outside temperature. This is
caused by the heat being radiated from the
engine.
23

Driver information system
Trip computer
Introduction
Applies to vehicles: with trip computer
The trip computer gives you information on cur­
rent and average fuel mileage, average speed ,
fuel range and driving tim e.
F ig. 9 Tri p computer display: Average fuel mileage
~ 9 a: co a,
The fo llow ing information is cont in uously evalu ­
ated by the trip comp uter and can be displayed
sequent ia lly in the instrument cl uster display:
Fuel range
T he est ima ted c ruising range in miles ( km) ap­
pears in the d isp lay. Thi s tells you how far your
veh icle w ill be able to t ravel o n the cu rrent tank
of fuel and with the same driv ing style . The dis­
p lay changes in increments of 5 miles (10 km).
T he cruising r ange is calc ulated based on the fuel
consumption for the last 18 m iles (30 km). If you
drive conse rvatively, the cruis ing range will in­
crease.
Average fuel mileage
T he aver age f uel economy in MPG (l/ 100 km)
since you last cleared the memo ry appears in this
disp lay . You ca n use this display to a djust your
d riving technique to achieve a desired mi leage .
Current fuel mileage
T he inst antaneo us f ue l cons umption in miles per
g all on ( l/ 10 0 km) i s show n in th is display . Yo u
can use t his disp lay to ad just yo ur driv ing tech ni­
que to ach ieve a desi red mileage .
Fue l cons umption is re cal culat ed a t inte rv a ls of
33 y ards (30 meters). T his d isp lay sw itches to
24
gallons/hour (liters/ho ur) when the vehicle is not
moving .
Average speed
The average s peed in mp h (km/h) s in ce you last
re se t t he memory ap pears in t he di sp lay.
Elapsed time
The length of time that yo u have been drivi ng
s ince you last reset the me mory a ppears in this
display .
Distance
The distance th at has been covered since the last
time the memory was cleared appears in the dis­
play .
(D Tips
- Fu el consumptions (ave rage and cur rent),
range and speed are d isp layed in metric
units on Canadian mod els.
- All stored values will be lost if the vehicle
battery is disconnected.
Memories
Applies to vehicles: with trip computer
The trip computer is equipped with two fully au ­
tomatic memories as well as an efficiency pro­
gram* .
Fig. 1 0 Trip compute r display: mem ory level 1
"' 0 .,, 0 ci: co a,
Yo u c an swit ch between the t rip compu ter 1 a nd
2 and the efficiency pro gram * by pressing the
I RESET I butto n® ~ page 25, fig. 11 .
You can tell w hich memory level is currently a c­
tive by the number o r th e sig n in t he display
~fig. 10. The da ta from the single -trip memory
(memory level 1) is bei ng d isplayed if a
D ..,.

..... N
0 ::..:: co ..... ..... appears in the display. If a fJ is shown, then the
data from the tota l-trip memory is being dis­
p layed (memory level 2). The fuel pump nozzle
ii indicates the efficiency program*
¢page 26.
Single-trip memory (Trip computer 1)
The single-trip memory stores the trip informa­
tion from the time the ignition is turned on until
it is turned off.
If the trip is continued within 2
hours
from the time the ignition was turned off,
the new data w ill be included in the calculat ion of
the current tr ip inf ormat ion . If the trip is inter ­
rupted fo r
more than 2 hours the memory is re­
set automat ica lly.
Total-trip memory (Trip computer 2)
Unlike the single-trip memory, the total-trip
memory is not reset automatically. This permits
you to evaluate your driving data for the entire period between manual resets.
Efficiency program*
The efficiency program can help you to use less
fuel¢
page 26.
Operation
App lies to vehicles: with trip computer
The trip computer is controlled by two switches
on the windshield wiper lever.
F ig. 11 W indsh ield w iper lever: controls for t he tr ip com·
puter
Operating
• To display the trip computer memory levels,
press the
I RESET ! button@¢ fig. 11 repeated­
ly until the desired memory level is shown in
the display.
Driver information system
• To display trip information within a memory
level, press the top or bottom part of the func­
tion se lection switch @.
T he trip computer will not ope rate un less the ig­
nition is on. When you turn on the ignition, the
function that was in use when you last turned the
ignition off will be disp layed.
In addition to information about the trip comput­
er (trip computer 1, 2 and the efficiency pro­
gram*), information about other systems can a l­
so be shown in the display. To sw itch the display
between the different information, tap the
I RESET I button @ briefly.
Resetting values to zero
• Select a value in the desired trip computer or in
the efficiency program *.
• Press and hold the
I RESET ! button @for at
least one second . All values in the selected trip
computer or in the efficiency program* are re­
set to zero.
If the data in trip computer 1 are de leted, then
the va lues in the efficiency program* will a lso be
reset.
With some vehicle equipment levels, the values
for the single trip or total trip memory can also
be reset in the Infotainment system
¢ page 25.
(0 Tips
All stored values will be lost if the vehicle bat­
tery is disconnected.
Basic Settings for the trip computer
Applies to vehicles: with trip computer
The radio or MMI* operating unit is used for set ­
ting the trip computer 's basic settings.
• Select: Function button !CAR !> Instrument
cluster
> On-board computer 1 or On-board
computer 2.
The values in the sing le-trip or the total-trip
memory can a ll be reset to zero at the same time
under
Reset in the menu. .,..
25

Driver information system
In addition, you can determine what information
from the trip computer should be shown in the instrument cluster disp lay . If one of the pieces of
driver information is turned
Off , that driver infor­
mation will not be shown in the display. The in­
formation will continue to be calculated by the
tr ip computer and can be turned back
On at any
time .
(D Tips
-This function is not available on all veh icles.
- The driving information in the efficiency
program is also reset to zero with the sin­
gle-trip memory .
Gearshift Indicator
Appl ies to ve hicles: w ith manu al transmiss ion an d ge arshi ft
i n di cato r
This indicator can help conserve fuel.
Fig. 12 Display: Gearshift indicator
In order to become familiar with the gearshift in­
d ictor, at firs t just drive the way you are used to.
If the current gear - and the driving situation -is
not the best one for conserving fuel, then the in­
d icator will display the recommended gear. The
display shows the current gear and the gear that
is recommended
c>fig. 12.
-Upshifting The display will light up to the right
of the gear currently selected if it is recom­
mending a higher gear.
-Downshifting: The display will light up to the
left of the gear current ly selected if it is recom­
mending a lower gear.
Sometimes the indicator will recommend skip­
ping a gear (3
> 5).
26
If there is no gearshift recommendation, then
just drive in the appropriate gear for conserving
fuel.
(D Note
This indicator can help you conserve fuel. This
indicator is not meant to show you which gear
you should a lways be in in all driving situa­
tions. Somet imes, in situations such as pass­
i ng, driving through mountains or when tow­
i ng a tra iler, there won't be any gearshift rec­
ommendat ion.
@ Tips
The display does not light up when the clutch
pedal is be ing depressed .
Efficiency program
Description
Applies to vehicles : wi th trip co mpute r with eff ic ie n cy pro­
gram
Fig. 13 Disp lay: efficiency program
.. PressthelRESETlbutton @c>poge25, fig.11
repeatedly until the efficiency program appears
in the display .
The efficiency program can help you to use less
fuel. It evaluates driving information in reference
to fuel consumpt ion and shows other equipment
i nfluencing consumption as well as shift recom­
mendat ions. Fuel economy messages
c>
page 28 provide tips for efficient driv ing.
The eff ic iency program uses distance and con­
sumption data from trip computer
1. If the data
are deleted in the efficiency program, those val­
ues are also reset in trip computer
1.

,....,
N
0
""' CX) ,....,
I.Cl U"I ,....,
I.Cl ,....,
Enhanced shift indicator
Applies to vehicles: with manual transmiss ion and tr ip com­
p uter with eff iciency program
F ig. 14 Display: enhanced s hift i ndicator
• In the efficiency program, press the function
selection switch¢
page 25, fig. 11@ repeat­
edly until the enhanced shift indicator appears
in the display.
The efficiency program also has an enhanced
shift ind icator. This enhanced shift indicator fol­
lows the same concept as the "standard" shift in­
dicator¢
page 26. The selected and the recom­
mended gears are highlighted in colors like a
traffic light .
The color of the circle indicates if the most suita­ b le gear is engaged or if you should shift up or
down.
Green circle w ithout or No gear or the most
with a gear suitable gear is engag-
ed
Yellow circle¢
fig. 14 Shift up or down one
gear
Red circle Shift up two gears
(D Note
This enhanced shift indicator can help you
conserve fuel. It is not designed to recom­
mend the correct gear in all dr iving situa­
tions . Only the dr iver can decide which gear is
correct in certain dr iving situations such as
when passing another veh icle, dr iving on hill s
or towing a trailer.
Driver in forma tion system
(D Tips
-The enhanced shift indicator display is dif­
ferent in vehicles with a monochrome dis­
play.
- The "standard" shift indicator* disappears
when the enhanced shift indicator is dis­
played.
Other equipment
Applies to vehicles: with trip computer with eff ic ie n cy pro­
gram
Fig. 15 Display : other equ ipment
• In the effic iency program, press the funct ion
select ion switch ¢
page 25, fig. 11 @ repeat­
ed ly until the other equipment appears in the
disp lay.
Other equipment that is currently affecting fuel
consumption is listed in the eff ic iency program.
T he display shows up to three other items of
equipment @. T he equipment using the most
fuel is listed first. If more than three items using
fuel are switched on, the equipment that is cur­ rently using the most fuel is displayed.
A scale @also shows the current total consump­
tion of all other equipment .
27

Driver information s ystem
Fuel economy messages
Applies to vehicles: with trip computer with efficiency pro­
gram
F ig. 16 D isplay: fuel eco nomy message
Fue l economy messages are displayed when fue l
consumption is inc reased by certain conditions. If
you follow these fuel economy messages, you can reduce your vehicle's consumption of fuel. The
messages appear automatically and are only dis ­
p layed in the eff iciency program . The fuel econo­
my messages turn off automat ica lly afte r ace r­
tain period of t ime.
"' To turn a fuel economy message off immed i­
ate ly after it appears , press t he I R ESE T I button
¢ page 25, fig. 11 @ , or
"' Press t he f unct ion sele ct io n sw itch
~ page 2 5,
fig. 11
® ·
(D Tips
- Once you have t urned a fue l economy mes­
sage off, it will on ly appea r again after you
turn the ig nition on ag ain.
- T he fuel economy messages a re not d is­
p layed in every ins tance, but rather in in ter­
v al s over a per io d of t ime.
Service interval display
The service interval display reminds you when
your next service is due .
The schedule for the next oil change o r inspec­
tion is calc ulated a utomatically and displayed ac ­
cord ingly. The display works in two stages:
28
Service reminder
3 0 days before the next service is due , a servi ce
r eminder appears in the display when you turn on
the ignition .
After abou t
5 seconds the display swit ches bac k
to normal. The dist ance a nd time rem aining are
u pda ted each time the ignit ion is turned on unt il
the date due for service is reached.
Service due
Whe n the d ue date for se rvice is rea ched, the
message
Service due! appears in the inst rument
cl uster immed iate ly after you tu rn o n the igni­
tion . Add itiona lly, a warn ing tone sounds. A fter
about
5 seconds the display switches back to nor­
mal.
Calling up the service schedules
I f or w hen an oil change o r inspec tion is due, can
be shown in the radio or MMI * display by se lect­
i ng the service interval display in the car menu.
Se lect
I CAR I fu nction button > Se rvice interval
display
or ! CAR I function button > Car systems *
control button > Ser vicing & checks .
Resetting the s ervice interval display
Yo ur a utho rized Aud i dea ler will rese t the corre­
sponding service schedu le after performing the
approp riate service on your vehicle . You also have
the possibility to reset t he oi l change schedule
after having pe rformed an oil change accord ing
to Audi specifications. Select
I CA R I fu nction but­
ton
> Service interval display > Re set oil change
interval
or ICA RI fu nction button > Car systems *
control button > Servicing & check s > Reset oil
change interval.
(D Note
- Only reset the oil c hange display when you
h ave completed an o il change.
- If you disconnect the battery term inals, no
calcu lations can be made for the se rvice in­
te rv al display dur ing th is time and no se rv ­
i c e rem inder will appear. Remembe r th at
ob serv ing the pro per serv ice intervals is vi-
ta lly im po rt an t to extending the life o f your .,.